Auger-type granular fertylizer distributor: matemathical model and dynamic simulation

The objective of this study was to model mathematically and to simulate the dynamic behavior of an auger-type fertilizer applicator (AFA) in order to use the variable-rate application (VRA) and reduce the coefficient of variation (CV) of the application, proposing an angular speed controller θ' for the motor drive shaft. The input model was θ' and the response was the fertilizer mass flow, due to the construction, density of fertilizer, fill factor and the end position of the auger. The model was used to simulate a control system in open loop, with an electric drive for AFA using an armature voltage (V A) controller. By introducing a sinusoidal excitation signal in V A with amplitude and delay phase optimized and varying θ' during an operation cycle, it is obtained a reduction of 29.8% in the CV (constant V A) to 11.4%. The development of the mathematical model was a first step towards the introduction of electric drive systems and closed loop control for the implementation of AFA with low CV in VRA.

Modeling and simulation of forced-air cooling of strawberries using variable convective coefficient

In the forced-air cooling process of fruits occurs, besides the convective heat transfer, the mass transfer by evaporation. The energy need in the evaporation is taken from fruit that has its temperature lowered. In this study it has been proposed the use of empirical correlations for calculating the convective heat transfer coefficient as a function of surface temperature of the strawberry during the cooling process. The aim of this variation of the convective coefficient is to compensate the effect of evaporation in the heat transfer process. Linear and exponential correlations are tested, both with two adjustable parameters. The simulations are performed using experimental conditions reported in the literature for the cooling of strawberries. The results confirm the suitability of the proposed methodology.

Substrate with Organosuper® for cucumber seedlings formation in protected environments and polystyrene trays

Culture environments, trays and doses of organic compost were evaluated in the formation of cucumber seedlings (Cucumis sativus L.). Five environmental conditions were tested: (A1) a greenhouse with height of 2.5 m, covered with polyethylene film, (A2) nursery with height of 2.5 m, monofilament fabric, 50% shading, (A3) nursery with height of 2.5 m, heat-reflective screen, 50% shading, (A4) nursery with a height of 1.8 m, covered with coconut tree straw and (A5) greenhouse with height of 4.0 m, covered with polyethylene film, with zenith opening and thermo-reflective cloth under the plastic. Trays of 72 (R1) and 128 (R2) cells were filled with 93% soil and 7% organic compound (S1), 86% soil and 14% organic compound (S2) and 79% soil and 21% organic compound (S3). It was used a randomized design in split-split-plot scheme, with five replicates (environments x trays x substrates). The greenhouses provide the best environments for the formation of cucumber seedlings. A tray of 72 cells is the best container, promoting more vigorous seedlings in substrate with soil and 7 or 14% organic compound.

Formation of beetroot seedlings in different protected environments, substrates and containers in Aquidauana region, State of Mato Grosso do Sul, Brazil

This study with beetroot seedlings, cultivar Top Tall Early Wonder, was carried out at the State University of Mato Grosso do Sul (UEMS/Aquidauana), from October to November 2008. Three environments of cultivation were used: greenhouse; nursery with monofilament screen of 50 % of shading; and nursery with aluminized thermal reflective screen of 50% of shading. In these environments, three polystyrene trays of 72, 128 and 200 cells, filled with four substrates, were tested: soil; Plantmax®; coconut fiber and vermiculite. There were no replication environments and then each one was considered an experiment alone. For each environment, it was adopted a completely randomized design in factorial scheme 3x4 (three trays x four substrates), with four replications, performing individual analysis of variance and joint analysis of experiments for environment comparisons. The monofilament screen is the best environment for seedlings produced in tray of 72 cells, and the greenhouse was the best environment for seedlings produced in trays of 128 cells. The best seedlings were formed in the tray of 72 cells. Vermiculite was the best substrate.

Production of baruzeiro seedling in different protected environments and substrates

The high seedlings quality is essential for deployment of homogeneous orchards. This study evaluated the baruzeiro (Dipteryx alata Vog) seedlings formation on different substrates within protected environments. It was used substrates with100% of cattle manure; 100% of cassava stems; 100% of vermiculite; 50% of cattle manure + 50% of cassava stems; 50% of cattle manure + 50% of vermiculite; 50% of cassava stems + 50% of vermiculite; and + ⅓ of cattle manure + ⅓ of cassava stems + ⅓ of vermiculite. These substrates were tested in protected areas: greenhouse; black shade net of 50% shading; and aluminized thermo-reflective screen of 50% shading. A completely randomized experimental design with five replicates of four plants was adopted. Initially, data were submitted to analysis of individual variance of the substrates, in each environment of cultivation, then performing the evaluation of the residual mean square and the analysis of these environments together for comparison. The best substrate for baruzeiro seedlings was pure vermiculite. The substrates with 100% of manure and the substrate with 33.33% of the mixed studied materials can be used for seedlings formation. The environment with screen can be indicated for the production of baruzeiro seedlings, since it gave vigor to the seedlings.

Production of tomato seedlings using different substrates and trays in three protected environments

The seedlings production is an essential part for vegetables production. Thus, this study aimed to evaluate the environment, the substrates and the containers in the development of tomato seedlings, cv. Santa crus Kada Gigante, in Aquidauana -MS, Brazil region, from October to November, 2008. Polystyrene trays with 72; 128 and 200 cells, filled with four substrates (soil; Plantmax®; coconut fiber and vermiculite) were tested in three protected environments (greenhouse; screened with Sombrite® and screened with Aluminet®). The experimental design was completely randomized, factorial scheme 3x4 (three trays x four substrates), with four replications, being analyzed individual variance analysis and joint analysis for the environments. The environment with screens (Sombrite® and Aluminet®), the trays with 72 cells and the vermiculite produced better results.

Simulation of the energy performance of maize production integrated to pig farming

The study evaluated the energy performance of pig farming integrated with maize production in mechanized no-tillage system. In this proposed conception of integration, the swine excrement is used as fertilizers in the maize crop. The system was designed involving the activities associated to the pig management and maize production (soil management, cultivation and harvest). A one-year period of analysis was considered, enabling the production of three batches of pigs and two crops of maize. To evaluate the energy performance, three indicators were created: energy efficiency, use of non-renewable resources efficiency and cost of non-renewable energy to produce protein. The energy inputs are composed by the inputs and infrastructure used by the breeding of pigs and maize production, as well as the solar energy incident on the agroecosystem. The energy outputs are represented by the products (finished pigs and maize). The results obtained in the simulation indicates that the integration improves the energy performance of pig farms, with an increase in the energy efficiency (186%) as well as in the use of the non-renewable energy resources efficiency (352%), while reducing the cost of non-renewable energy to produce protein (‑58%).

Experimental evaluation of the performance of a wireless sensor network in agricultural environments

The aim of this study was to perform an experimental study to evaluate the proper operation distance between the nodes of a wireless sensor network available on the market for different agricultural crops (maize, physic nut, eucalyptus). The experimental data of the network performance offers to farmers and researchers information that might be useful to the sizing and project of the wireless sensor networks in similar situations to those studied. The evaluation showed that the separation of the nodes depends on the type of culture and it is a critical factor to ensure the feasibility of using WSN. In the configuration used, sending packets every 2 seconds, the battery life was about four days. Therefore, the autonomy may be increased with a longer interval of time between sending packets.

Volume of polyethylene bags for development of papaya seedlings in protected environments

The objective of this study was to test container of polyethylene bags and protected environments on the papaya seedlings production, from May to August of 2008, in Aquidauana state of Mato Grosso do Sul (MS), Brazil. Five bags of polyethylene were used: 7.5 cm x 11.5 cm, 205.9 cm³; 8.4 cm x 10.6 cm, 238.1cm³; 10.0 cm x 16.5 cm, 525.2 cm³; 12.0 cm x 12.0 cm, 550.0 cm³ and 15.0 cm x 21.5 cm, 1539.8 cm³. These containers were placed in three protected environments: greenhouse; screened nursery with Sombrite® and screened nursery with Aluminet®. Because there is no replication of growing environment, each one was considered an experiment. For each cultivation environment, it was adopted a completely randomized design with eight replications of two plants each. Initially, data were submitted to analysis of individual variance of the container (for each cultivation environment), then performing the evaluation of the residual mean squares and the combined analysis of these environments for comparison of protected environments. The greenhouse and nursery with thermal reflector screen produced the best seedlings. The bags of 15.0 x 21.5 cm produced the best papaya seedlings. The Dickson Quality Index pointed the nursery with screen of thermal reflector as the environment that produced the most vigorous seedlings, when using the best container.

Coffee seedlings in different substrates and protected environments

The production of high-quality seedlings is a critical factor for successful implementation of a determined crop in the field. In order to evaluate the production of coffee seedlings, experiments were conducted with different substrates and in different protected environments. Treatments consisted of evaluation of the following substrates: 50% cattle manure + 50% commercial substrate, 50% cattle manure + 50% vermiculite, 50% commercial substrate + 50% vermiculite, 1/3 cattle manure + 1/3 commercial substrate + 1/3 vermiculite, 50% cattle manure + 50% sand, 1/3 sand + 1/3 cattle manure + 1/3 commercial substrate and 50% commercial substrate + 50% sand. These substrates were tested in different protected environments: agricultural greenhouse, mesh screen with 50% shading, aluminized screen with 50% shading, black screen with 30% shading, black screen with 70% shading, nursery with a buriti straw roof and full sunlight. In each environment, the experiments were conducted in a completely randomized design with five replicates of four plants each followed by joint analysis. The substrates containing 50% cattle manure associated with vermiculite or the commercial substrate may be indicated for production of coffee seedlings. Screened environments with 30, 50 and 70% shading resulted in the highest quality seedlings.

Seedlings of Acrocomia aculeata in diferent substrates and protected environments

The seedling production stage is the key to achieve uniformity in tree breeding stage. This study evaluated "bocaiúva" (Acrocomia aculeata) seedling formation, with pre-germinated seeds in different substrates and protected environments, in the University of Mato Grosso do Sul State, Aquidauana, MS. As substrates, we used 100% cattle manure (M), 100% cassava branches (CB), 100% vermiculite (V), 50% cattle manure + 50% cassava branches, 50 % cattle manure + 50% vermiculite, 50% cassava branches + 50% vermiculite and ⅓ cattle manure + ⅓ cassava branches + ⅓ vermiculite. These substrates were tested in a greenhouse covered with 150 µm low density polyethylene (LDPE) film under thermo-reflective screen with 50% shading under film; black screen with 50% shading on the sides; black monofilament screen with 50% shading set on roof and sides; and aluminized thermo- reflective screen with 50% shading set on roof and sides. The completely randomized experimental design with 5 replications of 5 plants each was adopted. Initially, data were submitted to analysis of substrate individual variance in each growing environment, then performing the waste mean square evaluation and their environment joint analysis for comparison. The best growing environment is the thermo-reflective screen compared to LDPE greenhouse and black screen set. All substrates containing manure are recommended for bocaiúva seedlings formation. The pure cassava branch is not indicated for seedling, even using chemical fertilizer.

Hydrological simulation using SWAT model in headwater basin in Southeast Brazil

Hydrological models are important tools that have been used in water resource planning and management. Thus, the aim of this work was to calibrate and validate in a daily time scale, the SWAT model (Soil and Water Assessment Tool) to the watershed of the Galo creek , located in Espírito Santo State. To conduct the study we used georeferenced maps of relief, soil type and use, in addition to historical daily time series of basin climate and flow. In modeling were used time series corresponding to the periods Jan 1, 1995 to Dec 31, 2000 and Jan 1, 2001 to Dec 20, 2003 for calibration and validation, respectively. Model performance evaluation was done using the Nash-Sutcliffe coefficient (E NS) and the percentage of bias (P BIAS). SWAT evaluation was also done in the simulation of the following hydrological variables: maximum and minimum annual daily flowsand minimum reference flows, Q90 and Q95, based on mean absolute error. E NS and P BIAS were, respectively, 0.65 and 7.2% and 0.70 and 14.1%, for calibration and validation, indicating a satisfactory performance for the model. SWAT adequately simulated minimum annual daily flow and the reference flows, Q90 and Q95; it was not suitable in the simulation of maximum annual daily flows.

Bartlett-Lewis of rectangular pulse modified model: estimate of parameters for simulation of precipitation in sub-hourly duration

The Bartlett-Lewis Rectangular Pulse Modified (BLPRM) model simulates the precipitous slide in the hourly and sub-hourly and has six parameters for each of the twelve months of the year. This study aimed to evaluate the behavior of precipitation series in the duration of 15 min, obtained by simulation using the model BLPRM in situations: (a) where the parameters are estimated from a combination of statistics, creating five different sets; (b) suitability of the model to generate rain. To adjust the parameters were used rain gauge records of Pelotas/RS/Brazil, which statistics were estimated - mean, variance, covariance, autocorrelation coefficient of lag 1, the proportion of dry days in the period considered. The results showed that the parameters related to the time of onset of precipitation (λ) and intensities (μx) were the most stable and the most unstable were ν parameter, related to rain duration. The BLPRM model adequately represented the mean, variance, and proportion of the dry period of the series of precipitation lasting 15 min and, the time dependence of the heights of rain, represented autocorrelation coefficient of the first retardation was statistically less simulated series suitability for the duration of 15 min.

Mathematical simulation parameters for drying of cassava starch pellets

Based on experimental tests, it was obtained the equations for drying, equilibrium moisture content, latent heat of vaporization of water contained in the product and the equation of specific heat of cassava starch pellets, essential parameters for realizing modeling and mathematical simulation of mechanical drying of cassava starch for a new technique proposed, consisting of preformed by pelleting and subsequent artificial drying of starch pellets. Drying tests were conducted in an experimental chamber by varying the air temperature, relative humidity, air velocity and product load. The specific heat of starch was determined by differential scanning calorimetry. The generated equations were validated through regression analysis, finding an appropriate correlation of the data, which indicates that by using these equations, can accurately model and simulate the drying process of cassava starch pellets.

Soursop seedlings: emergence and development under different cultivation environments and substrates – Part I

ABSTRACT Seedling quality is crucial to obtain vigorous plants in the field. This study aims to evaluate the emergence and development of soursop seedlings in different substrates in protected environments. The experiment was conducted at the Mato Grosso do Sul State University and carried out using five protected environments: greenhouse, greenhouse with thermo-reflective screen, nursery with monofilament screen, nursery with thermo-reflective screen, and nursery with palm thatch. The substrates (S) consisted of cattle manure (M), humus (H), cassava branches (C), and vermiculite (V) as in the following ratios: S1 = H + V (1:3), S2 = H + V (1:1), S3 = H + V (3:1), S4 = H + C (1:3), S5 = H + C (1:1), S6 = H + C (3:1), S7 = M + V (1:3), S8 = M + V (1:1), S9 = M + V (3:1), S10 = M + C (1:3), S11 = M + C (1:1), S12 = M + C (3:1), S13 = H + M + V (1:1:1), S14 = H + M + C (1:1:1), and S15 = H + M + V + C (1:1:1:1). For the statistical analysis, each of those environments was considered as an experiment in which was used the completely randomized design; subsequently, it was performed a combined analysis of them. In summary, the greenhouse with thermo-reflective screen and combined substrates with “M + V” promote greater development of the seedlings. High concentrations of “V” or “C” cause no beneficial effect on soursop seedlings.