Performance evaluation of hydrocyclone filter for microirrigation

In this study a hydrocyclone filter of 20 cm was selected and its performance was evaluated by studying the variation of discharge, pressure drop, influent concentration, and filtration efficiency with elapsed time of operation. The filter was tested with clean water to determine clean pressure drop and later it was tested with four concentrations of solid suspension, viz. 300; 600; 900 and 1,200 mg L-1. In the concentration of 300 mg L-1, the variation of pressure drop was low. But for the other concentrations of solid suspension, the variation was significant. The maximum pressure drops obtained were 41.19, 45.11, 50.01 and 52.95 kPa at 350, 390, 280 and 190 minutes of elapsed time, respectively. The maximum efficiency of solid suspension was 30.3, 32.96, 43.89 and 52.5% where as the minimum efficiencies were 9.91, 9.93, 9.62 and 9.9%, respectively. The hydrociclone tested presented inefficiency to filter small particles as clay. The initial removal efficiency of higher concentration was bigger than for lower concentration but, the final efficiency are almost the same irrespective of the concentration of solid suspension. The present tested hydrocyclone could be used as a pre-filter microirrigation to prevent emitter clogging.

Efficiency of pneumatic and horizontal perforated disk meter mechanism in corn no-tillage seeders in soil with different mobilization reports

This work objectified to evaluate the efficiency of two meter mechanism of corn seeds when submitted to different forward speed and soil management system during the non-tillage seeding. It was used a factorial design in randomized blocks. The factors whose effects were examined were related to the seeders with pneumatic and horizontal disk meter mechanisms for the distribution of the seeds, to the set tractor-seeder forward speeds (4.4; 8.0 and 9.8 km h-1), and to the soil management system considering the corn no-tillage seeding over minimum tillage with chisel plow and the no-tillage system for the seeding of oat culture (Avena strigosa Schreb). It was verified that the forward speed didn't influence the initial and final stands of plants but it interfered in the regularity of longitudinal distribution of plants. The smallest speed provided the largest percentile of normal spacing between plants. The pneumatic meter mechanism presented better performance than the horizontal disk perforated in the longitudinal distribution of plants. About corn productivity aspect it's indifferent the recommendation of use for pneumatic and perforated horizontal disk meter mechanism of seeds.

Evaluation of five sugar cane planters

Brazil is the world biggest producer of sugar cane with an area of 7x10(6) hectares. Mainly the system used for planting is the semi-mechanized one, which consists in opening the furrows with a machine, manually allocating the fractioned stalks and then covering the furrows done by the machines. The great amount of human labor used in the semi-mechanized system is becoming harder to find and also more expensive, indicating the need of a fully mechanized operation. Currently in Brazil these agriculture machines industries offers six different types of fully mechanized sugar cane planters (two types of whole stalks for planting and four using mechanized harvested stalks known as billets). All of them plant in two furrows simultaneously in 1.5 m row spacing. This study analyzed five different machines and the following variables: Working Speed (km h-1); Effective Capacity (ha h-1), Drawbar Force (kgf), Draw Bar Power (in HP), Fuel Consumption (L h-1) and Costs (US$ ha-1) comparing them with the semi-mechanized system. This research also characterized the stalks for planting as viable gems number (%), non viable gems number (%) and billet length (m). And lastly the mechanized planting system is cheaper than the conventional one and none of the machines has an adequate mechanism for placing the right amount of sugar cane seed.

Obstruction of drippers as a result of application of moisturized whitewash in irrigation water

Plug dynamics of non compensate drip tubes were evaluated, by the precipitation of moisturized whitewash [Ca(OH)2], which is used in the fertigation for the bulb pH control of the trademarks Azud, Amanco, Naandan, Netafim, Petroisa, Queen Gil, with flow rate varying between 0.4 to 3.0 L h-1 usually used in the country. For this matter, increasing doses of Ca(OH)² were applied in the irrigation water, from 0.01 g L-1 to 1.84 g L-1. The flow rate of each drip tube was measured in intervals of time initially of 7 days, later of 15 days of system operation, totaling a time of 100 days of operation, corresponding to nine applications or 432 hours. The coefficient of variation (CV), and relative rate flow (Qr) were evaluated. The results pointed differences among the evaluated emitter regarding the occurrence of the clogging, and the models G2 and G5 presented the smallest levels of flow rate variation comparing to the models G6, G7 and G9.

Water application uniformity and fertigation in a dripping irrigation set

The purpose of this study was to evaluate the uniformity of distribution coefficient (UDC) and coefficient of variation (CV) of a familiar set of irrigation, classifying it the ASAE standard. The irrigation and fertigation are determined by two methods the KELLER & KARMELI and DENÍCULI . The two experiments were subjected to varying pressures: 12, 14, 16 and 18 kPa, in a completely randomized design of twenty samples composed of flows with three replications. Urea, potassium chloride (KCl) and ammonium phosphate (MAP) were the elements used for fertigation. The system consisted of a 200 L tank, which supplied another container of 30 L, it was moved vertically to control the pressure. The data was statistically compared between treatments for each methodology. In fertigation the best pressure was 16 kPa and was classified as "excellent" for UDC (91.03%) and "marginal" for C.V. (7.47%). For the irrigation treatment, the best pressure was 16 kPa rated "excellent" for UDC (91.2%) and "marginal" for C.V. (7.68%). The DENÍCULI et al. (1980) methodology proved more reliable for the evaluation of drip systems. It was observed that this set has good uniformity of distribution, but with great variability in flows.

Comparison of metering mechanisms of corn seed

It was compared the performance of the metering mechanism of corn seeds (Zea mays) in direct seeding in an area of ​​200 ha, a property in Piraí do Sul, State of Paraná - PR, in Brazil. It was seeded 4 maize hybrids, 50 ha of each, with seeds of different sieves. The experiment was conducted in a randomized block design (RBD), with 3 treatments and 9 repetitions for each corn hybrid. The treatments were the pneumatic seed of metering mechanisms, horizontal perforated disc with and without ramp®. The plots were 40 m² and were distributed at the early, middle and late sowing. The variables analyzed in each corn hybrid were initial population, faulty spacing, multiple spacing, acceptable spacing, and yield components. As there were no significant differences in the variables, it was concluded that the quality of seeding with different systems of distribution was similar in the different sieves of distributed corn seeds.

Irrigation management in pruned coffee tree crop

It was evaluated the effect of irrigation management on the production characteristics of coffee cultivar Acaiá MG-1474, planted in spacing of 3.00 m x 0.60 m, pruned in 2004, and irrigated by drip since the planting, in 1997. The experimental designed used was of randomized blocks with five treatments and four replications. The treatments consisted of irrigation management strategies, applying or not applying controlled moisture deficit in layer of 0 to 0.4m, in dry seasons of the year: A = no irrigation (control), B = irrigation during all year considering the factor of water availability in the soil (f) equal to 0.75, C = irrigation during all year considering f = 0.25, D = irrigation during all year, but in January /February /March /July /October /November /December with f = 0.25 and April /May /June /August /September with f = 0.75, E = irrigation only during April /May /June /August /September with f = 0.25. From July /2005 to June /2007 the applied water depth was defined based on Class A pan evaporation (ECA) and the period from July/2007 to June/2008 based on readings of matric potential of soil obtained from Watermark® sensors. Each plot consisted of three rows with ten plants per row, considering as useful plot five plants of center line. The results indicated that the E irrigation management was the most suitable for technical reasons.

Coffea arabica (cv Catuaí) production and bean size under different population arrangements and soil water availability

The purpose of this research was to evaluate the effect of drip irrigation under different population arrangements on the phytometric features, coffee productivity and bean size classification according to sieve retention. The experiment with Coffea arabica L. cv Catuaí was carried out in Mococa, São Paulo, Brazil. The experimental design was a 6 x 2 factorial scheme in randomized blocks, with four replications. The six densities of plantation were E1 (1.60 x 0.50 m); E2 (1.60 x 0.75 m); E3 (1.60 x 1.00 m); E4 (3.20 x 0.50 m); E5 (3.20 x 0.75 m) and E6 (3.20 x 1.00 m), which were divided according to the availability of water (irrigated - I - or non-irrigated - NI - groups). Data were submitted to analysis of variance and averages compared by Tukey test at 1 and 5% of probability. Descriptive analysis of coffee beans according to sieve classification was performed. Irrigation promoted an increase in plant height, crown diameter and production of processed coffee when compared with the NI group. Interaction between population arrangement and irrigation was observed, with an increase in production and crown diameter as the spacing was decreased. Therefore, irrigation provided significant increase in coffee bean size.

Longitudinal distribution of bean seeds in horizontal plate meter operating with one or two seed outlets

This study aimed to evaluate the effect of horizontal plate meter with oblong holes operating with one or two seed outlets at different speeds over the accuracy of longitudinal distribution of common bean seeds (Phaseolus vulgaris L.). The experiment was performed in laboratory using the meter with one and two seed outlet points in relation to ten tangential disk plate speeds (0.03 to 0.30 m s-1). It was used a complete randomized design with four replications, summing up 80 experimental treatments. Tangential speed quantitative factor was estimated through a 2nd order polynomial regression. There was no significant difference in the behavior of the seed meter operating with one or two outlets in the metering of bean seeds in all tested speeds, with percentage of single seeds spacing over 60% in tangential speeds below of 0.24 m s-1.

Modalities for soil preparation and gypsum application in ultisol: stem productivity of sugarcane

The study was conducted in an area of expansion of sugarcane at Vale do Paraná factory in Suzanápolis city - São Paulo (SP), in Brazil, in the northwestern region of the State of São Paulo. It was used the sugarcane variety RB92-5345, 1.5m of spacing between rows, in an Ultisol. The study aimed to evaluate the productivity of sugarcane and first ratoon and some soil chemical attributes in function of soil tillage and application or not of gypsum. The experimental design was randomized blocks with six treatments, in a factorial 3x2 and six replicates, the main treatments were soil tillage with three equipments, moldboard plow, chisel plow, and heavy harrow, and two secondary treatments with application of 1 t ha-1of gypsum and no gypsum. After each harvest of cane, the soil was characterized as to its fertility indicators in layers of 0.0-0.15; 0.15-0.30 and 0.30-0.45m. Differences in values of soil chemical attributes due to the methods of preparation occurred in the sugarcane did not last until the harvest of the 1st ratoon cane, and also did not influence the crop productivity. The gypsum application resulted in higher values ​​of total recoverable sugar (TRS) and the productivity of tons of stems per hectare (TSH) to sugarcane and 1st ratoon cane, respectively, confirming the initial hypothesis.

Quality of peanut mechanical sowing in function of seeding density and size of the seeds

ABSTRACTPeanut crop (Arachis hypogaeaL.) mechanization has been improved over the years; however there are drawbacks that affect the quality of operations. Thus, this article’s objectives were to evaluate the operational performance of the mechanized sowing of peanut crop according to seeding densities (10, 14, and 18 seeds m-1) and seed sizes (21 and 23 mm). It was observed that the seeds of 23 mm had shorter average number of days to emergence and a higher percentage of emergences, occurring the opposite to the seeding density of 18 seeds m-1. The higher the seeding density, the largest was the plant stand, whereas the 23 mm seed obtained the best results and the same with the seeding density of 14 seeds m-1 that had a higher percentage of normal spacing. The densities of 14 and 18 seeds m-1 reflected in higher yields, being always superior to the 23 mm seeds.

Backpressure effects on the flow-pressure relation of driplines

ABSTRACT For drip irrigation design and management, it is necessary to know the relation between flow and pressure acting on emitters. In the case of subsurface drip irrigation, the backpressure phenomenon may change the hydraulic characteristics of emitters. Thus, this study aimed at determining such relationship between flow and pressure of different driplines in surface and subsurface conditions; aiming to find possible differences in hydraulic behavior. We tested four emitter types; two pressure compensating (D5000 and Hydro PCND) and two non-pressure compensating (TalDrip and Jardiline). Emitter flow rates were attained in atmospheric conditions and submerged in water, in which submergence levels represented backpressure. Assays were performed using inlet pressures of 80, 100, 120, and 150 kPa for the Hydro PCND dripline and 25, 50, 100, and 150 kPa for the other ones; the backpressures were of 0.49, 1.47, 2.45, 4.41 and 6.37 kPa with four replications. The emitters had their proportionality constants and discharge exponents changed in submerged applications, representing backpressure effect. Non-pressure compensating emitters had their discharge exponent decreased, while in pressure compensating ones, it was increased. Backpressure reduced emitter flow rates at all evaluated pressures.

Characterization of Lubricating Oil Using Ultrasound

This paper presents an ultrasonic method to measure small concentrations of water in lubricating oil. It uses an ultrasonic measurement cell composed by a piezoceramic emitter (5 and 10 MHz), and a large aperture PVDF receiver that eliminates diffraction effects. The propagation velocity, attenuation coefficient and density of several samples of water-in-oil emulsion were measured. The concentrations of water of the samples were in the range of 0 to 5% in volume, and the results showed that these low concentrations can be discriminated within a resolution of 0.2% in the studied range, using the measurement of the propagation velocity.

Seed bank from soil of coffee plantations associated with grevillea trees

This study aimed to study the composition and dynamics of seed bank from soil of coffee plantations associated with grevilea trees in the experimental fields of the Southwest Bahia State University, on Vitória da Conquista campus. The experiments were carried out from September 2006 to May 2007. The coffee trees (Coffea arabica) were sown at three x one m spacing, associated with grevillea trees (Grevillea robusta) and maintained at densities of 277, 139, 123, 69, 62 and 31 plants ha-1, under direct sunlight. One hundred grams of soil were taken from each treatment with four repetitions and later identified and counted with a 10x magnifying glass. To determine seedling emergence, four soil samples of 1000 g were collected from each experimental field and transported to the greenhouse. Seedling emergence was observed by counts after 15, 30 and 45 days. The experimental design was randomized blocks of seven treatments (soil from different tree densities) and four replicates; the experimental unit consisted of a plastic tray (0, 30 x 0.22 x 0.06 m) containing 1.000 g of soil. The variables utilized to characterize the bank and its dynamics were: relative frequency, relative density, relative abundance, importance index and species diversity (Shannon-Weaver index).Increased number of monocotyledon seeds and sprouts were verified in the treatments maintained under full sunlight.

Planting density of gliricidia when intercropped with corn for weed control

Reduced use of herbicides that cause environmental pollution problems is of great interest in modern agriculture. Soil mulching with gliricidia (Gliricidia sepium) branches does not have an allelopathic effect on corn, but decreases weed populations. The objective of this study was to evaluate the effects of gliricidia planting density, when grown as an intercrop, on weed control and corn yield parameters. A randomized block design with split-plots and ten replicates was adopted. Corn cultivars AG 1051 and BM 3061 were grown without hoeing, with two hoes (at 24 and 44 days after planting), and intercropped with gliricidia (planted simultaneously with corn, between crop rows, using two seedlings/pit, spaced at 30, 40, or 50 cm). Twenty-one weed species were found in the experimental area. Increased gliricidia planting density reduced weed biomass, but no difference was found between weed biomass in the intercrop and weed biomass in non-hoed corn. Gliricidia intercropped with corn, planted at a row spacing of 30 cm, did not significantly differ from hoed corn in most characteristics considered to evaluate green corn yield, although mean values were smaller. As to the number and weight of marketable green ears, reductions of 5% and 13%, respectively, were observed. Intercropping caused a 17% reduction in grain yield, reducing the losses (36%) observed in non-hoed corn by more than 50%. The highest green ear yield and grain yield values were obtained with two hoeings, while the lowest values were observed for non-hoed corn. The cultivars did not differ regarding green ear yield and grain yield.