Chemical characteristics and Kraft pulping of tension wood from Eucalyptus globulus labill

Tension (TW) and opposite wood (OW) of Eucalyptus globulus trees were analyzed for its chemical characteristics and Kraft pulp production. Lignin content was 16% lower and contained 32% more syringyl units in TW than in OW. The increase in syringyl units favoured the formation of β-O-4 bonds that was also higher in TW than in OW (84% vs. 64%, respectively). The effect of these wood features was evaluated in the production of Kraft pulps from both types of wood. At kappa number 16, Kraft pulps obtained from TW demanded less active alkali in delignification and presented slightly higher or similar pulp yield than pulps made with OW. Fiber length, coarseness and intrinsic viscosity were also higher in tension than in opposite pulps. When pulps where refined to 30°SR, TW pulps needed 18% more revolutions in the PFI mill to achieve the same beating degree than OW pulps. Strength properties (tensile, tear and burst indexes) were slightly higher or similar in tension as compared with opposite wood pulps. After an OD0(EO)D1 bleaching sequence, both pulps achieved up to 89% ISO brightness. Bleached pulps from TW presented higher viscosity and low amount of hexenuronic acids than pulps from OW. Results showed that TW presented high xylans and low lignin content that caused a decrease in alkali consumption, increase pulp strength properties and similar bleaching performance as compared with pulps from OW.

Extractives and energetic properties of wood and charcoal

Charcoal production stands out as a raw material for the production of renewable energy. To assess wood quality in energy terms, studies have focused more on the holocellulose and lignin content than on the role of extractives. The objective of this study was to evaluate the relationship between the extractive content in cold water, in dichloromethane and total on energy properties of wood and charcoal, from six trees species. The extractives were removed with different solvents to be recorded and gross calorific value of wood was determined. The wood was carbonized at 1.67°C/min heating rate until maximum of 450°C and residence time of 30 min. The extractive content was correlated with the gravimetric yield, apparent relative density, ash, volatile matter, fixed carbon and gross calorific value of charcoal. The removal of total extractives and extractives soluble in dichloromethane reduced the gross calorific value of wood of most species evaluated. The extractives removed in cold water did not correlate with the parameters of carbonization. The extractives content in dichloromethane correlated with volatile matter, fixed carbon and gross calorific value. Total extractive content correlated with gravimetric yield, apparent relative density and gross calorific value of charcoal.

COMPARISON BETWEEN WOOD DRYING DEFECT SCORES: SPECIMEN TESTING X ANALYSIS OF KILN-DRIED BOARDS

It is important to develop drying technologies for Eucalyptus grandis lumber, which is one of the most planted species of this genus in Brazil and plays an important role as raw material for the wood industry. The general aim of this work was to assess the conventional kiln drying of juvenile wood of three clones of Eucalyptus grandis. The specific aims were to compare the behavior between: i) drying defects indicated by tests with wood specimens and conventional kiln-dried boards; and ii) physical properties and the drying quality. Five 11-year-old trees of each clone were felled, and only flatsawn boards of the first log were used. Basic density and total shrinkage were determined, and the drying test with wood specimens at 100 °C was carried out. Kiln drying of boards was performed, and initial and final moisture content, moisture gradient in thickness, drying stresses and drying defects were assessed. The defect scoring method was used to verify the behavior between the defects detected by specimen testing and the defects detected in kiln-dried boards. As main results, the drying schedule was too severe for the wood, resulting in a high level of boards with defects. The behavior between the defects in the drying test with specimens and the defects of kiln-dried boards was different, there was no correspondence, according to the defect scoring method.

RELATIONSHIP BETWEEN CLIMATE VARIABLES, TRUNK GROWTH RATE AND WOOD DENSITY OF Eucalyptus grandis W. Mill ex Maiden TREES

ABSTRACT Climatic conditions stimulates the cambial activity of plants, and cause significant changes in trunk diameter growth and wood characteristics. The objective of this study was to evaluate the influence of climate variables in the diameter growth rate of the stem and the wood density of Eucalyptus grandis trees in different classes of the basal area. A total of 25 Eucalyptus trees at 22 months of age were selected according to the basal area distribution. Dendrometer bands were installed at the height of 1.30 meters (DBH) to monitor the diameter growth every 14 days, for 26 months. After measuring growth, the trees were felled and wood discs were removed at the DBH level to determine the radial density profile through x-ray microdensitometry and then re-scale the average values every 14 days. Climatic variables for the monitoring period were obtained and grouped every 14 days. The effect of the climate variables was determined by maximum and minimum growth periods in assessing trunk growth. These growth periods were related with precipitation, average temperature and relative air humidity. The re-scaled wood density values, calculated using the radial growth of the tree trunks measured accurately with steel dendrometers, enabled the determination of the relationship of small changes in wood density and the effect of the climatic variations and growth rate of eucalyptus tree trunks. A high sensitivity of the wood density to variation in precipitation levels was found.

NATURAL DURABILITY OF Eucalyptus dunnii Maiden, Eucalyptus robusta Sm., Eucalyptus tereticornis Sm. AND Hovenia dulcis Thunb. WOOD IN FIELD AND FOREST ENVIRONMENT

AB STRACT This study aimed at evaluating the natural durability of Eucalyptus dunnii, Eucalyptus robusta, Eucalyptus tereticornis and Hovenia dulcis woods submitted to a deterioration test in two environments, field and forest. The test samples were buried until half of their length (150 mm). Evaluations were carried out each 45 days, totalizing a 405-day period, with three-repetition withdrawal of each species for environment, totalizing nine samples from each environment, making up 24 test samples for evaluation. After percentage calculations of mass loss and resistance degree classification, the deterioration index was adopted for decomposition evaluation and fungal decay potential determination of test samples. The study has been carried out in completely randomized design (CRD), evaluated through analysis of variance (ANOVA) with subsequent comparison of means by Turkey' s test, in a 5%-level of probability of error, along with regression analysis. Eucalyptus tereticornis wood presented lesser mass loss in both environments. Hovenia dulcis presented lesser deterioration probability in both environments. Forest environment test samples presented greater mass loss percentages and lesser deterioration index.

Mapping of summer crops in the State of Paraná, Brazil, through the 10-day spot vegetation NDVI composites

The search for low subjectivity area estimates has increased the use of remote sensing for agricultural monitoring and crop yield prediction, leading to more flexibility in data acquisition and lower costs comparing to traditional methods such as census and surveys. Low spatial resolution satellite images with higher frequency in image acquisition have shown to be adequate for cropland mapping and monitoring in large areas. The main goal of this study was to map the Summer crops in the State of Paraná, Brazil, using 10-day composition of NDVI SPOT Vegetation data for 2005/2006, 2006/2007 and 2007/2008 cropping seasons. For this, a supervised digital classification method with Parallelepiped algorithm in multitemporal RGB image composites was used, in order to generate masks of Summer cultures for each 10-day composition. Accuracy assessment was performed using Kappa index, overall accuracy and Willmott's concordance index, resulting in good levels of accuracy. This methodology allowed the accomplishment, with free and low resolution data, of the mapping of Summer cultures at State level.

The influence of the season of the year and of dilution on the development of swine manure and wood shaves co-composting

The objective of this research was to study the influence of factors related to the proper management of pig manure (lower dilution) and the season of the year in the progress of the co-composting of pig manure with wood shavings and in the final quality of the compost resulting from the treatments. In the first experiment, two types of swine manure were used: a diluted one (2% Dry Matter - DM), typical from the management usually used in Brazil, and a more concentrated one (6% DM). The manures were incorporated into the wood shavings (6L:1kg) over the course of four weeks. The development of composting was accompanied by monitoring of temperatures inside the piles and the emission of CO2 and CH4 gases during 65 days, including the period of incorporation. The results showed that the diluted manure does not provide the minimum conditions for starting the process. After the incorporation period, any biomass heating was observed and neither the aerobic or anaerobic respiration of the microorganisms, resulting in a compost with low quality. In the second experiment, which evaluated composting in winter and summer during 85 days, it was found that the heat exchange with the environment influences the temperature generated within the piles. The lower temperatures significantly reduced the methanogenesis on the biomass.

Characterization and use of swine deep bedding ashes in cementitious composites

The deep bedding is a swine alternative production, especially in the finishing phase, whose byproduct can be recycled, reducing the environmental impact. The objectives of this study were to characterize the ash coming from the controlled burning of the swine deep bedding (SDBA) based on rice husk, and to evaluate their performance in composites as a partial substitute for Portland cement (PC). To measure the differences between SDBA and rice husk ash (RHA) as a reference, we have characterized: particle size distribution, real specific density, x-ray diffraction, electrical conductivity, scanning electron microscopy, chemical analysis and loss on ignition. Samples were prepared for two experimental series: control, and another one with the partial replacement of 30% of SDBA in relation to the mass of the Portland cement. According to the results obtained for physical and mechanical characterization, the composites with SDBA can be used as a constructive element in the rural construction.

Is professional recognition in plastic surgery related to activity in research

OBJECTIVE: To evaluate the relation of medical research, with the participation of prominent plastic surgeon in Congress.METHODS: We reviewed the scientific programs of the last 3 Brazilian Congress of Surgery, were selected 21 Brazilian plástic surgeons invited to serve as panelists or speakers in roundtable sessions in the last 3 congresses (Group 1). We randomly selected and paired by other members (associates) of the Brazilian Society of Plastic Surgery, with no participation in congress as speaker (Group 2). We conducted a search for articles published in journals indexed in Medline, Lilacs and SciELO for all doctors selected during the entire academic career and the last 5 years from March 2007 until March 2012. We assessed the research activity through the simple counting of the number of publications in indexed journals for each professional. The number of publications groups was compared.RESULTS: articles produced throughout career: Group 1- 639 articles (average of 30.42 items each). Group 2- 79 articles (mean 3.95 articles each). Difference between medias: p <0.001.CONCLUSION: The results demonstrate that the Brazilian Society of Plastic Surgery seeking professionals with a greater number of publications and journals of higher impact. This approach encourages new members to pursue a higher qualification, and give security to congressmen, they can rely on the existence of a technical criterion in the choice of speakers.

Plastic surgery in chest wall reconstruction: relevant aspects - case series

Objective: to discuss the participation of Plastic Surgery in the reconstruction of the chest wall, highlighting relevant aspects of interdisciplinaryness. Methods: we analyzed charts from 20 patients who underwent extensive resection of the thoracic integument, between 2000 and 2014, recording the indication of resection, the extent and depth of the raw areas, types of reconstructions performed and complications. Results: among the 20 patients, averaging 55 years old, five were males and 15 females. They resections were: one squamous cell carcinoma, two basal cell carcinomas, five chondrosarcomas and 12 breast tumors. The extent of the bloody areas ranged from 4x9 cm to 25x40 cm. In 12 patients the resection included the muscular plane. In the remaining eight, the tumor removal achieved a total wall thickness. For reconstruction we used: one muscular flap associated with skin grafting, nine flaps and ten regional fasciocutaneous flaps. Two patients undergoing reconstruction with fasciocutaneous flaps had partially suffering of the flap, solved with employment of a myocutaneous flap. The other patients displayed no complications with the techniques used, requiring only one surgery. Conclusion: the proper assessment of local tissues and flaps available for reconstruction, in addition to the successful integration of Plastic Surgery with the specialties involved in the treatment, enable extensive resections of the chest wall and reconstructions that provide patient recovery.

Non-linear analysis of laminated metal matrix composites by an integrated micro/macro-mechanical model

The present paper describes an integrated micro/macro mechanical study of the elastic-viscoplastic behavior of unidirectional metal matrix composites (MMC). The micromechanical analysis of the elastic moduli is based on the Composites Cylinder Assemblage model (CCA) with comparisons also draw with a Representative Unit Cell (RUC) technique. These "homogenization" techniques are later incorporated into the Vanishing Fiber Diameter (VFD) model and a new formulation is proposed. The concept of a smeared element procedure is employed in conjunction with two different versions of the Bodner and Partom elastic-viscoplastic constitutive model for the associated macroscopic analysis. The formulations developed are also compared against experimental and analytical results available in the literature.

Modelling of mechanical properties of CRFC composites under flexure loading

Carbon Fibre Reinforced Carbon (CFRC) Composites are increasing their applications due to their high strength and Young’s Modulus at high temperatures in inert atmosphere. Although much work has been done on processing and structure and properties relationship, few studies have addressed the modelling of mechanical properties. This work is divided in two parts. In the first part, a modelling of mechanical properties was carried out for two bi-directional composites using a model based on the Bernoulli-Euler theory for symmetric laminated beams. In the second part, acoustic emission (AE) was used as an auxiliary technique for monitoring the failure process of the composites. Differences in fracture behaviour are reflected in patterns of AE.

Effect of particle morphology on the mechanical and thermo-mechanical behavior of polymer composites

Fiber reinforced polymer composites have been used in many applications, such as in automobile, aerospace and naval industries, due basically to their high strength-to-weight and modulus-to-weight, among other properties. Even though particles are usually not able to lead to the level of reinforcement of fibers, particle reinforced polymer composites have been proposed for many new applications due to their low cost, easy fabrication and isotropic properties. In this work, polymer composites were prepared by incorporating glass particles of different morphologies on poly(aryl sulfones) matrices. Particles with aspect ratios equal to 1, 2.5 and 10 were used. The prepared composites were characterized using electron microscopy and thermal analysis. Mechanical properties of the composites were evaluated using a four-point bending test. The thermo-mechanical behavior of the obtained composites was also investigated. The results showed that the morphology of the particles alter significantly the mechanical properties of composites. Particles with larger values of aspect ratio led to large elastic modulus but low levels of strain at failure. This result was explained by modeling the thermo-mechanical behavior of the composites using a viscoelastic model. Parameters of the model, obtained from a Cole-Cole type of plot, demonstrated that interactions at the polymer-reinforcing agent interface were higher for composites with large aspect ratio particles. Higher levels of interactions at interfaces can lead to higher degrees of stress transfer and, consequently, to composites with large elastic modulus, as experimentally observed.

Chaos and Unpredictability in the Vibration of an Elasto-Plastic Beam

This contribution discusses the nonlinear dynamics of a pin-ended elasto-plastic beam with both kinematic and isotropic hardening. An iterative numerical procedure based on the operator split technique is developed in order to deal with the nonlinearities in the equations of motion. Free and forced responses for harmonic sinusoidal and square wave excitations are investigated. Numerical simulations present many interesting behaviors such as jump phenomena, sensitivity to initial conditions, chaos and transient chaos. These results indicate that there are practical problems in predicting the response of the beam even when periodic steady state response is expected.