An Hp-Adaptive Hierarchical Formulation for the Boundary Element Method Applied to Elasticity in Two Dimensions

This paper presents an HP-Adaptive Procedure with Hierarchical formulation for the Boundary Element Method in 2-D Elasticity problems. Firstly, H, P and HP formulations are defined. Then, the hierarchical concept, which allows a substantial reduction in the dimension of equation system, is introduced. The error estimator used is based on the residual computation over each node inside an element. Finally, the HP strategy is defined and applied to two examples.

Control of Structures with Cubic and Quadratic Non-Linearities with Time Delay Consideration

This paper studies the effect of time delay on the active non-linear control of dynamically loaded flexible structures. The behavior of non-linear systems under state feedback control, considering a fixed time delay for the control force, is investigated. A control method based on non-linear optimal control, using a tensorial formulation and state feedback control is used. The state equations and the control forces are expressed in polynomial form and a performance index, quadratic in both state vector and control forces, is used. General polynomial representations of the non-linear control law are obtained and implemented for control algorithms up to the fifth order. This methodology is applied to systems with quadratic and cubic non-linearities. Strongly non-linear systems are tested and the effectiveness of the control system including a delay for the application of control forces is discussed. Numerical results indicate that the adopted control algorithm can be efficient for non-linear systems, chiefly in the presence of strong non-linearities but increasing time delay reduces the efficiency of the control system. Numerical results emphasize the importance of considering time delay in the project of active structural control systems.

Obtention and characterization of gluten-free baked products

This work had as objective the development of gluten-free breads and muffins using rice flour and maize and cassava starches. From seven samples resulting from a Simplex-Centroid design, the sensory and instrumental analyses of specific volume, elasticity, and firmness were performed. For the sensory analysis, the optimized formulation contained 50% of rice flour and 50% of cassava starch, and for the instrumental evaluation, the optimal simultaneous point for the three conducted analyses were 20% of rice flour, 30% of cassava starch, and 50% of maize starch. A comparative analysis of specific volume, elasticity, firmness, and triangular test was performed with pre-baked, baked, and frozen bread. Physicochemical, nutritional, and microbiological analyses were performed for both bread and muffin according to the Brazilian legislation.

Fat reduction in the formulation of frankfurter sausages using inulin and pectin

The aim of this study was to evaluate the influence of different concentrations of inulin and pectin as fat substitutes on the chemical composition, texture, and sensory acceptance of frankfurter sausages. Six treatments were evaluated to test fat replacement: control (T0); low fat control (T1); low fat with 15% inulin (T2); low fat with 30% inulin (T3); low fat with 7.5% inulin and 7.5% pectin (T4); and low fat with 15% inulin and 15% pectin (T5). The addition of fibers increased the yield (T3 and T5; 98.96%), and the color parameters were slightly reduced (T3). Moisture (61.14%) and ashes (6.96%) of sausages with inulin and pectin were higher (T5), while shear force, hardness, fracturability, gumminess, and chewiness (T3 and T5) were slightly lower than those of the control. The addition of inulin (T2) increased the sensory acceptance of the sausages (5.75). Fat can be replaced with inulin and pectin in frankfurter sausages to produce healthy and functional products.

Application of extruded broken bean flour for formulation of gluten-free cake blends

The aim of this study was to determine the physical and microbiological characteristics of extruded broken beans flour, in addition to developing mixtures for gluten-free cake with these flours, evaluating their technological and sensory quality. Gluten-free formulations were prepared with 45%, 60% and 75% of extruded broken beans. All analyzes of the flours and mixtures for cakes were performed according to standard techniques found in the literature. Sensory analyzes of cakes applied the 9-point structured hedonic scale. Results were submitted to variance analysis and comparison of means test (Tukey, p<0.05). The use of extruded broken beans improved the water absorbed and water solubility index of the mixtures for gluten-free cake, and for the lower viscosity and retrogradation when compared to the standard formulation. All cakes were accepted (rate ≥ 7) for all the analyzed attributes. From the technological and sensory standpoints, the development of gluten-free cake mixtures is feasible with up to 75% of extruded broken beans.