Biofouling e biodeterioração química de argamassa de cimento portland em reservatório de usina hidroelétrica

Last decade Brazilian rivers experimented progressive biofouling of Limnoperna fortunei communities and Cordylophora caspia hydroids. The microhabitat is so favorable that in around 1.5 years L. fortunei increased from 0.39 to nearby 149,000 units/m². Ten Portland cement mortar samples were produced with 1: 3.5: 0.4 dosages and installed for 1 year at Salto Caxias Brazilian Power Plant reservoir in 0.5 m and 1.0 m deep to investigate the biofouling influence on hydraulic civil structures. SEM, EDS, visual investigation and XRF results indicate none direct chemical interrelationships between L. fortunei and the mortar samples. However C. caspia diminished the mortar surface resistance and caused cement paste leaching.

Uso das técnicas de infravermelho e de ressonância magnética nuclear na caracterização da reação ácido-base de um cimento odontológico experimental

Glass ionomer cements (GICs) are products of the acid-base setting reaction between an finely fluoro-alumino silicate glass powder and poly(acrylic acid) in aqueous solution. The sol gel method is an adequate route of preparation of the glasses used to obtain the GICs. The objective of this paper was to compare two powders: a commercial and an experimental and to investigate the structural changes during hardening of the cements by FTIR and Al MAS NMR. These analyses showed that the experimental glass powder reacted with organic acid to form the GICs and it is a promising material to manufacture dental cements.

Síntese e caracterização de nanopartículas de óxido de ferro suportadas em matriz carbonácea: remoção do corante orgânico azul de metileno em água

In this work were prepared composites of iron oxide and carbonaceous materials in two different weight proportions (Carbon/Fe 1/1 and 1/2). The physico-chemical properties of the composites were determined by temperature programmed reduction (TPR), adsorption/dessorption of N2, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and pulse titration H2. The XRD and XPS analysis showed a cubic iron oxide phase, identified as maghemite, formed over the carbon surface. The particle size of maghemite showed to be within 10-30 nm. Carbon/Fe 1/2 was the most active in MB removal kinetics and ESI-MS studies showed that MB removal by both composites leads to oxidized intermediates.

Especiação de cromo em cimentos e derivados de cimento brasileiros

A method for determination of Cr(III) and Cr(VI) in cement and cement-related materials was studied. Molecular absorption spectrophotometry based on 1,5-diphenylcarbazide as chromogenic reagent was used for determination of Cr(VI) after alkaline extraction. The total chromium concentration was determined using flame atomic absorption spectrometry (FAAS) after complete sample decomposition by fusion. The quantification of Cr(III) was accomplished by subtracting the Cr(VI) concentration from the total chromium concentration. The concentration of Cr(III) in the samples ranged from 10.9 to 88.0 mg kg-1, whereas only in few samples the Cr(VI) concentration was higher than the value established by the European Community to this type of sample [2 mg kg-1 Cr(VI)].

Avaliação do uso de poli(tereftalato de etileno) (PET) como matriz de imobilização de cinzas de incineradores

Industrial hazardous wastes must receive appropriate treatment to ensure a safe disposal to humans and environment. One of the techniques adopted for this purpose is the stabilization/solidification in polymer matrices. This paper evaluated the use of recycled polyethylene terephthalate as an incorporation matrix of incinerator ash. The polymer and the ash were submitted to an extrusion process in different percentages. The final product was evaluated through thermal and leaching tests and the leachate extracts constituents were determinated by atomic absorption spectrophotometry. The results showed a reduction in the release of substances up to 99% by mass for the conditions used.

Desempenho da matriz híbrida SiO2-quitosana na imobilização da lipase microbiana de Candida rugosa

Lipase from Candida rugosa was immobilized by covalent attachment on hybrid SiO2-chitosan obtained by sol-gel technique. A comparative study between free and immobilized lipase was provided in terms of pH, temperature, kinetic parameters and thermal stability on the olive oil hydrolysis. The pH and temperature for maximum activity shifted from 7.0 and 45 ºC for the free lipase to 7.5 and wide range of temperature (40-50 ºC) after immobilization. Kinetics parameters were found to obey Michaelis-Menten equation and K M values indicated that immobilization process reduced the affinity of enzyme-substrate; however Kd values revealed an increase of thermal stability of lipase.

Aplicação de métodos quimiométricos na caracterização de charutos utilizando extração por dispersão da matriz em fase sólida e análise por cromatografia gasosa acoplada à espectrometria de massas

In this work, the organic compounds of cigar samples from different brands were analyzed. The compound extraction was made using the matrix solid-phase dispersion (MSPD) technique, followed by gas chromatography and identification by mass spectrometry (GC-MS) and standards, when available. Thirty eight organic compounds were found in seven different brands. Finally, with the objective of characterizing and discriminating the cigar samples, multivariate statistical analyses were applied to data, e.g.; principal component analysis (PCA) and hierarchical cluster analysis (HCA). With such analyses, it was possible to discriminate three main groups of three quality levels.

Utilização do acetato de celulose produzido a partir da celulose extraída do caroço de manga como matriz para produção de sistemas microparticulados

Cellulose acetate produced from mango seed fibers cellulose was used as a matrix for preparation of microparticles empty and load with acetaminophen (Paracetamol) in order to evaluate the incorporation of an active agent during the formation of microparticles. The microparticles are characterized by Fourier Transformed Infrared spectroscopy (FTIR), Differential Scanning Calorimetry (DSC) and Scanning Electron Microscopy (SEM). The incorporation of paracetamol can be confirmed by the change in value of glass transition temperature (Tg). The formation of microparticles spherical was observed by SEM and showed an average diameter of 1.010 and 0.950 mm for empty and load microparticles respectively.

Efeito da adição de serragem de couro tratada quimicamente nas propriedades do cimento Portland

The sheave leather was subjected to chemical treatment in an attempt to immobilize chromium ion in a matrix of cement. Cementitious pastes were obtained by adding different proportions of waste treated solutions (5 and 10% compared to the cement mass) and the pH and setting time (hardening) were measured. Aiming to check the leather influence in Portland cement pastes, the phases formation were observed by X-ray diffraction (XRD). The results showed that the pretreatment was effective for the waste dissolution and the pH of treated waste chemical solutions did not influence significantly the characteristics of cement paste, with a slight increase in setting time results.

Determinação espectrofotométrica de cloreto em cimento após preparo de amostra por piroidrólise

A method based on pyrohydrolysis was proposed for cement sample preparation and further chloride determination by spectrophotometry using flow injection analysis. Analytical parameters were evaluated and, under the selected conditions, the calibration curve was linear in the range of 0.2 to 10.0 µg mL-1 with r2 = 0.998. The limit of detection was5 µg g-1 of chloride and the relative standard deviation was less than 7%. The proposed pyrohydrolysis method is relatively simple and can be used for sample preparation for further spectrophotometric determination of low concentrations of chloride in cement.

Acúmulo de cargas elétricas em propelente sólido compósito com matriz de polibutadieno líquido hidroxilado

Composite solid propellants prepared with HTPB prepolymer - Hydroxyl Terminated Polybutadiene, AP - Ammonium Perchlorate as oxidizer and aluminum particles as an additive metal, have characteristics of high electrical resistivity. The loading process of the polymer matrix did not obtain homogeneity, resulting in clusters, mainly of metal particles. The effect of clustering in the composite was studied and observed experimentally, and this effect was one of the factors explaining the phenomenon of electrical charging of the composite. This electrical potential, when discharged abruptly, can generate an electric spark with sufficient energy for sustained ignition of a solid rocket motor.

Obtenção e caracterização de matriz apropriada para sistemas de liberação prolongada: estudos de liberação dos herbicidas atrazina e diuron

This study aimed to produce and characterize a novel material from fish scales and chitosan for use as a medium for the extended release of herbicides. The mechanism of release for the herbicides atrazine and diuron was influenced by diffusion and swelling according to the power law kinetic model. The atrazine release time was seven days, while that of diuron was four days. The results of this study will contribute to the development of environmental matrices for herbicide release systems.

OBTENÇÃO DE COMPÓSITOS HÍBRIDOS BASEADOS EM HIDROGÉIS E CIMENTO PORTLAND

In this study, a novel hybrid composite based on biodegradable hydrogel and Portland cement with promising technological properties was reported. In the first step, a full 23 with central point factorial design was utilized to obtain the enhanced polyacrylamide-carboxymethylcellulose hydrogel compositions. A mathematical model was devised, indicating that the 3 main variables were significant and the AAm and MBAAm variables positively contributed to the mode and showing that the CMC variable had the opposite contribution. In the second step, these compositions were mixed with Portland cement to obtain the hybrid composites. The presence of cement improved the mechanical properties of polymeric matrices, and electronic microscopic micrographics revealed that the hydrogels were well adhered to the cement phase and no phase separation between hydrogel and cement was detected. Finally, using the energy dispersive X-ray technique, the elements Na, Mg, Al, Si, S, K, Ca and Fe were detected in the polymeric matrix, consistent with the hybrid composite formation.

Utilização de um eletrodo de grafite recoberto com PbO2 incorporado em matriz de PVC como eletrodo indicador em titulações coulométricas

A aplicação de um eletrodo sensível a íons H3O+, obtido pelo recobrimento de um eletrodo de grafite com uma membrana polimérica contendo PbO2 incorporado em uma matriz de PVC (PbO2-PVC), como eletrodo indicador em titulações coulométricas de neutralização, foi investigada. As leituras dos potenciais foram feitas usando o eletrodo indicador de PbO2-PVC e para comparação dos resultados foi usado um eletrodo de vidro combinado (EVC). As curvas de titulação monitoradas com o eletrodo de PbO2-PVC apresentaram características semelhantes àquelas monitoradas com o EVC e os tempos de equivalência obtidos foram concordantes a um nível de confiança de 95%. O eletrodo de PbO2-PVC apresentou resposta linear no intervalo de pH 2 a 12 com inclinação de Nernst de -57,6 ± 0,1 mV/pH (r= 0,9998), sendo o tempo de resposta deste eletrodo bem menor do que aquele obtido com o EVC. O eletrodo de PbO2-PVC é de fácil construção, possui baixo custo e tempo de vida útil superior a 4 meses, equivalente a (pelo menos 1200 determinações por membrana polimérica).