Synergistic and antimicrobial properties of commercial turmeric (Curcuma longa) essential oil against pathogenic bacteria

Several studies have shown the antimicrobial and antioxidant properties of turmeric (Curcuma longa), widely used in food industry as a colorant, among other functions. The aim of this study was to determine the antioxidant and antimicrobial properties of turmeric essential oil against pathogenic bacteria and to study the influence of the addition of ascorbic acid on the prevention of polyphenols oxidation. The commercial turmeric essential oil alone did not show bactericidal activity against the microorganisms studied, Listeria monocytogenes and Salmonella typhimurium, but when combined with ascorbic acid, it showed significant antibacterial activity. The highest antimicrobial activity of turmeric essential oil against Salmonella typhimurium was 15.0 ± 1.41 mm at the concentration of 2.30 mg.mL-1 of essential oil and 2.0 mg.mL-1 of ascorbic acid. With regard to Listeria monocytogenes, the largest zone of inhibition (13.7 ± 0.58 mm) was obtained at the same concentrations. The essential oil showed antioxidant activity of EC50 = 2094.172 µg.mL-1 for the DPPH radical scavenging method and 29% under the concentration of 1.667 mg.mL-1 for the β-carotene bleaching method.

Evaluation of the use of PetrifilmTM EB count plates for the enumeration of Enterobacteriaceae in poultry samples

A test that is rapid, simple, accurate, not expensive, gives rapid results, and is sensitive enough to detect low levels of microorganisms would be the most suitable for food industry routine laboratories, or even for a public health laboratories. A ready-to-use alternative, commercially available method is the PetrifilmTM EB method. The aim of this study was to evaluate whether there is a statistically significant difference between the conventional methods based on Violet Red Bile Glucose Agar and the alternative 3M TM Petrifilm (EB) method for the enumeration of Enterobacteriaceae in poultry carcasses. This study also assessed whether the alternative method showed ability to produce results that were directly proportional to the concentration of the target (approximately 270 colony-forming unit.mL-1). A total of 120 poultry carcasses samples showed a significant difference (p < 0.05) between the populations obtained by the two methods, and the conventional method showed low proportionality between the dilutions. On the other hand, the PetrifilmTM EB quantification system showed the capacity to produce results that are proportional to the concentration of the analyte in samples in the concentration range from 1 to 256 colony-forming unit.mL-1.

Evaluation of the efficacy of commercial sanitizers against adhered and planktonic cells of Listeria monocytogenes and Salmonella spp.

Antimicrobial activities of two commercial disinfectants, alone or combined with heat, against three Salmonella strains and three Listeria monocytogenes strains were studied. The efficacy of disinfectants against planktonic bacteria and bacteria attached to three food contact industrial surfaces (stainless steel, polytetraflourethylene, and rubber) was investigated. The tests were conducted using the sanitizer (quaternary ammonium compounds, and alquyldiethylenediamineglycine and di-alquyldiamineethylglycine) concentrations recommended by the manufacturers, and concentrations twice and four times higher than those values. The recommended concentrations were not effective to kill bacteria, especially when they were attached to surfaces. Concentrations of disinfectants twice and four times higher than those recommended were needed to fully eliminate planktonic bacteria. These same sanitizer concentrations were not sufficient to remove attached bacteria. To remove them from the surfaces, a treatment with recommended concentrations in combination with heat was needed. Our results indicate that these two pathogenic bacteria could survive common sanitation programs used in the food industry.

Proximate and mineral composition of industrialized biscuits

The aim of this study was to analyze the proximate and mineral composition of 21 types of biscuits. All biscuits showed high fat contents, significantly different (P < 0.05) from those described on the labels, except for three brands. Insoluble fiber fractions were predominant in the analyzed samples. Among the 21 biscuits analyzed, 16 showed food label values 20% higher than those allowed by law, according to RDC 360, for fat, protein, total fiber, calcium, and sodium levels. This difference reached 273% for the sodium content. The calcium content was included only on the label of three samples analyzed, and the values described were significantly lower than those obtained analytically. Considering that biscuits are consumed by people of all age groups and of different socioeconomic levels, the results can contribute to the plans for health policies, such as surveillance of nutritional labeling, ensuring the reliability of the information provided by the food industry and enabling the identification of the relationship between dietary factors and the occurrence of non-transmissible chronic diseases.

Changes in the physicochemical and microbiological properties of frozen araça pulp during storage

Araça belongs to the Myrtaceae family and is popularly known as araçá-comum, araçá-azedo, or araçá-do-campo. Frozen fruit pulp is of great importance for the food industry, which can produce it at the time of harvest, store it, and use it according to the demand of the consumer market and/or as an ingredient in the formulation of products such as yogurt, candies, and ice creams among others. The aim of this study was to evaluate the physical, chemical, and microbiological stability of frozen araça pulp during 12 months of frozen storage. It was observed that the levels of moisture (90.55-88.75%), ash (0.34-0.26%) total soluble sugars (7.11-6.62%), sucrose (3.55-1.39%), soluble pectin (0.24-0.23%), total pectin (0.5-0.46%), pH (3.82-2.31%), organic acids (698.12-122.25 µg.g-1 citric acid), and phenolic compounds (6.22-0.00 mg GAE.100 g-1) decreased during storage, whereas the levels of protein (0.61-0.83%), lipids (0.14-0.38%), total carbohydrates (8.36-9.78%), calorific value (37.14-45.86 kcal.100 g-1), reducing sugars (3.51-5.21%), soluble solids (5.17-6.0%), total antioxidant capacity (6.89-35.13%), and color parameters (L*49.75-50.67; a*0.79-1.82 and b*22.5-25.19) increased over the one-year storage period. According to the chemical and microbiological parameters assessed, the product can be stored for 12 months without loss of quality with addition of citric acid as a preservative.

Use of the spray chilling method to deliver hydrophobic components: physical characterization of microparticles

Food industry has been developing products to meet the demands of increasing number of consumers who are concerned with their health and who seek food products that satisfy their needs. Therefore, the development of processed foods that contain functional components has become important for this industry. Microencapsulation can be used to reduce the effects of processing on functional components and preserve their bioactivity. The present study investigated the production of lipid microparticles containing phytosterols by spray chilling. The matrices comprised mixtures of stearic acid and hydrogenated vegetable fat, and the ratio of the matrix components to phytosterols was defined by an experimental design using the mean diameters of the microparticles as the response variable. The melting point of the matrices ranged from 44.5 and 53.4 ºC. The process yield was melting point dependent; the particles that exhibited lower melting point had greater losses than those with higher melting point. The microparticles' mean diameters ranged from 13.8 and 32.2 µm and were influenced by the amount of phytosterols and stearic acid. The microparticles exhibited spherical shape and typical polydispersity of atomized products. From a technological and practical (handling, yield, and agglomeration) points of view, lipid microparticles with higher melting point proved promising as phytosterol carriers.

Influence of spray drying operating conditions on microencapsulated rosemary essential oil properties

Spray drying is an important method used by the food industry in the production of microencapsulated flavors to improve handling and dispersion properties. The objective of this study was to evaluate the influence of the process conditions on the properties of rosemary essential oil microencapsulated by spray drying using gum Arabic as encapsulant. The effects of the wall material concentration (10-30%), inlet air temperature (135-195 ºC), and feed flow rate (0.5-1.0 L.h-1) on the moisture content, hygroscopicity, wettability, solubility, bulk and tapped densities, particle density, flowability, and cohesiveness were evaluated using a 2³ central composite rotational experimental design. Moisture content, hygroscopicity and wettability were significantly affected by the three factors analyzed. Bulk density was positively influenced by the wall material concentration and negatively by the inlet air temperature. Particle density was influenced by the wall material concentration and the inlet air temperature variables, both in a negative manner. As for the solubility, tapped density, flowability, and cohesiveness, the models did not fit the data well. The results indicated that moderate wall material concentration (24%), low inlet air temperature (135 ºC), and moderate feed flow rate (0.7 L.h-1) are the best spray drying conditions.

Whole and crushed nutlets of chia (Salvia hispanica) from Mexico as a source of functional gums

The objective of this study was to characterize the chemical and functional properties of Mexican chia (Salvia hispanica) gums extracted from defatted whole and crushed nutlets using the Soxhlet and SFE-CO2 methods. Chia gums have interesting chemical and functional properties for the food industry. The oil and gum yields were in the range of 1.98-16.42% and 5.81-12.60%, respectively. The defatting procedure did not affect significantly the oil and gum extraction; the nutlet type (whole or crushed) was the only parameter influencing the yield. The proximate composition and the protein and fiber contents of chia gum were evaluated. Low contents of protein and fiber and high NFE levels were found in whole nutlet gums. The functional properties of chia gum extracted from whole and crushed nutlets with the Soxhlet and SFE-COs methods showed the following ranges of water absorption capacity of 62.64 to 143.66 g/g, water adsorption capacity of 0.69 to 1.35 g/g, and water and oil holding capacity of 100 to 149.28 g/g and19.5 to 40.4 g/g, respectively. The rheological behavior exhibited by the gums was pseudoplastic or shear thinning. From a functional perspective, chia gum is an important food component due its emulsifier and stabilizer potentials.

Composition and color stability of anthocyanin-based extract from purple sweet potato

AbstractPurple sweet potato (PSP) can provide products with attractive color besides nutritious benefits in food processing. So, the compositions and color stability of an aqueous anthocyanin-based PSP extract were investigated in order to promote its wide use in food industry. PSP anthocyanins were extracted with water, and nine individual anthocyanins (48.72 ug mL–1 in total, 24.36 mg/100 g fresh PSP in yield) were found by HPLC analysis. The PSP extract also contained 17.11 mg mL–1 of protein, 0.44 mg mL–1 of dietary fiber, 2.82 mg mL–1 of reducing sugars, 4.02 ug mL–1 of Se, 54.21 ug mL–1 of Ca and 60.83 ug mL–1 of Mg. Changes in color and stability of the PSP extract, as affected by pH, heat, light and extraction process, were further evaluated. Results indicated that PSP anthocyanins had good stability at pH 2.0-6.0, while the color of PSP extract kept stable during 30 days of storage at 20 °C in dark. Both UV and fluorescent exposure weakened the color stability of PSP extract and UV showed a more drastic effect in comparison. A steaming pretreatment of fresh PSP is beneficial to the color stability.

Chemical quality parameters and bioactive compound content of brazilian berries

There is a growing consumer demand for higher healthy foods such as berries which are a rich source of phenolic compounds. The current work evaluated blackberry cultivars: Cherokee, Tupy and Xavante; raspberry cultivars: Heritage, Fallgold and Black; and the hybrid Boysenberry. All berries were grown under homogenous subtropical conditions in Brazil. Black raspberry, Cherokee and Tupy blackberry cultivars showed the highest ratio between soluble solid contents and titratable acidity, and Fallgold and Heritage raspberry showed the highest titratable acidity. Total phenolic content ranged from 2.03 to 5.33 g kg–1 fresh weight and total anthocyanin content registered values from 0.41 to 1.81 g kg–1 fresh weight. The most common phenolic acids were gallic, p-coumaric and ellagic, and for anthocyanins: cyanidin-3-glucoside and malvinidin-3-glucoside. Antioxidant capacity ranged from 14.13 to 21.51 mol equivalent trolox kg–1 fresh weight. Black raspberry, all blackberry cultivars and the Boysenberry hybrid are appropriate to be consumed fresh, while Fallgold and Heritage raspberries are recommended to the food industry. Due to their phenolic richness and antioxidant properties, these fruits are of great interest to the fresh fruit market and to pharmaceutical industries. These results could help breeders and growers when planning the cultivar selection according to their foreseeable destination.

Study on creation of an indocalamus leaf flavor

Abstract Flavors represent a small but significant segment of food industry. Sensory characteristics play an important role in the process of consumer acceptance and preference. Indocalamus leaf takes on a pleasant odor and indocalamus leaf flavor can be used in many products. However, indocalamus leaf flavor formula has not been reported. Therefore, developing an indocalamus leaf flavor is of significant interests. Note is a distinct flavor or odor characteristic. This paper concentrates on preparation and creation of indocalamus leaf flavor according to the notes of indocalamus leaf. The notes were obtained by smelling indocalamus leaf, and the results showed that the notes of indocalamus leaf flavor can be classified as: green-leafy note, sweet note, beany note, aldehydic note, waxy note, woody note, roast note, creamy note, and nutty note. According to the notes of indocalamus leaf odor, a typical indocalamus leaf flavor formula was obtained. The indocalamus leaf flavor blended is pleasant, harmonious, and has characteristics of indocalamus leaf odor.

Alternatives to reduce sodium in processed foods and the potential of high pressure technology

Abstract In most industrialized countries, the sodium intake exceeds the nutritional recommendations. In this sense the search for healthier foods has led the food industry to review their formulations in relation to food components such as salt, which is associated with increased risk of chronic diseases. As a result, different strategies for reducing salt levels in processed foods have been investigated. Among the technological options available, the high-pressure processing has stood out by presenting intrinsic technological advantages that can contribute to optimization of food formulations with low / reduced sodium contents. This review provides a brief overview of the key strategies and use of high pressure in the development of reduced-salt products.

Evaluation of the antimicrobial activity of pecan nut [Carya illinoinensis (Wangenh) C. Koch] shell aqueous extract on minimally processed lettuce leaves

Abstract Pecan nutshell is a residue from food industry that has potential to be used as biopreservative in foods. The objective of this study was to evaluate the antimicrobial activity of pecan nutshell aqueous extract in vitro and its effectiveness to inhibit spoilage microorganisms on lettuce leaves. The results indicate that the aqueous extract presents inhibitory activity against important foodborne pathogenic bacteria such as Listeria monocytogenes, Salmonella Enteritidis, Staphylococcus aureus, Bacillus cereus, Aeromonas hydrophila and Pseudomonas aeruginosa. Antimicrobial activity was not observed against Corynebacterium fimi, Clostridium perfringens, Escherichia coli, and the phytopathogenic fungi tested. When applied onto lettuce leaves, pecan nutshell extract reduced the counts of mesophilic and psychrotrophic bacteria in 2 and 4 log CFU/g, respectively, during storage of leafy for 5 days at refrigeration temperature (5 °C). The extract was not effective to inhibit yeast on lettuce leaves. Thus, the aqueous extract of pecan shell showed great potential to be used as a natural preservative in foods, acting mainly in the inhibition of spoilage and pathogenic bacteria.

Application of alkaline waste from pulp industry to acid soil with pine

In Brazil extensive areas are covered with pine forests, planted for pulp and paper production. This industry generates solid alkaline waste, such as dregs. The application of this dregs to forest soils is an alternative for soil acidity correction and plant nutrient supply, as well as a solution for its proper disposal. The purpose of this study was to compare the residual effect of surface application of dregs and dolomitic lime on (a) changes in the physical and chemical properties of an acidic soil and (b) pine tree development. The experiment was carried out in 2004 in Bocaina do Sul, Santa Catarina, consisting of the application of increasing dreg and lime rates to a Pinus taeda L. production area, on a Humic Cambisol, in a randomized block design with four replications and 10 x 10 m plots. The treatments consisted of levels of soil acidity amendments corresponding to the recommendations by the SMP method to reach pH 5.5 in the 0-20 cm layer, as follows: no soil amendment; dregs at 5.08 (1/4 SMP), 10.15 (1/2 SMP) and 20.3 Mg ha-1 (1 SMP); and lime at 8.35 (1/2 SMP) and 16.7 Mg ha-1 (1 SMP). Soil layers were sampled in 2010 for analyses of soil chemical and physical properties. The diameter at breast height of the 6.5 year old pine trees was also evaluated. Surface application of dregs improved soil chemical fertility by reducing acidity and increasing base saturation, similar to liming, especially in surface layers. Dregs, comparable to lime, reduced the degree of clay flocculation, but did not affect the soil physical quality. There was no effect of the amendments on increase in pine tree diameter. Thus, the alternative to raise the pH in forest soils to 5.5 with dregs is promising for the forestry sector with a view to dispose of the waste and increase soil fertility.

Characterization of a hydrolyzed oil obtained from fish waste for nutraceutical application

The fish industry generates high volume of waste from fish oil that can have the extraction of its lipids used as nutraceuticals and foods. The objective of this study was to produce unsaturated fatty acids from industrialized fish oil by means of a differentiated hydrolysis process. The samples used were crude fish oil obtained from Campestre industry and characterized through physical-chemical parameters, according to AOCS: acidity, peroxide, saponification, iodine and percentage of free fatty acids and also obtained the fatty acid profile through derivatization method for gas chromatography. The results obtained for the oleochemical indices for refined oil were similar to the data found on the literature. The content of polyunsaturated fatty acids (PUFA) was found of 32,78%, with 9,12% of docosahexaenoic (DHA) and 10,36% of eicosapentaenoic (EPA), regarding monounsaturated fatty acids (MUFA) content was of 30,59% in the hydrolyzed fish oil in relation to refined (20,06%). Thus, it can be concluded that the hydrolysis process used for oils from fish-waste was satisfactory on the production of absolute yield of lipids in the process and significant preservation on the percentages of EPA and DHA, interesting on the production of nutraceuticals and nutrition of aquatic animals, including shrimp in captivity.