Effect of Sequential Cold Shocks on Survival and Molting Rate in Triatoma infestans Klug

The survival and molting incidence in Triatoma infestans, a vector of Chagas disease, were investigated following sequential shocks at 0ºC in fifth instar nymphs under moderate fasting and full nutritional conditions. The shocks were separated by intervals of 8 h and 24 h at 30ºC. The results indicated that in terms of insect survival, T. infestans is tolerant to a single cold shock at 0ºC even for 12 h, or to sequential cold shocks, regardless of the nutritional state of the specimens. In terms of molting rate, fasting enhanced the tolerance to sequential cold shocks, but did not exceed the tolerance acquired by fully-nourished specimens, except when cold shocks were separated by an 8 h interval at 30ºC. The protective action elicited by fasting was assumed to be additive to that induced by a single mild cold shock or sequential cold shocks. The cold-tolerance response of T. infestans may have favoured its survival in areas of South America with low temperatures, even considering that this species is predominantly associated with human habitats.

Changes in nuclear phenotype frequencies following sequential cold shocks in Triatoma infestans (Hemiptera, Reduviidae)

The nuclear phenotypes of Malpighian tubule cells in fifth instar nymphs of Triatoma infestans, one of the most important vectors of Chagas disease, were studied following sequential shocks at 0ºC, separated by intervals of 8 h and 24 h at 30ºC, under conditions of moderate fasting and full nourishment. The insects pertained to colonies reared in the laboratory and originated from domestic specimens collected in the Brazilian states of São Paulo (north) and Minas Gerais (south). Since nuclear phenotypes in this species are affected by single cold shocks, it was expected that these phenotypes could also be changed by sequential shocks. Nuclear phenotypes indicative of mechanisms of cell survival (nuclear fusion and heterochromatin decondensation) and cell death (apoptosis and necrosis) were observed concomitantly in all the conditions tested. Nuclear fusion and heterochromatin decondensation were not found relevant for the presumed acquisition of the cold-hardening response in T. infestans. The decreased frequency of apoptosis and necrosis following sequential cold shocks including under fasting conditions, indicated that tolerance to sequential cold shocks occurred in T. infestans of the mentioned origin.

Effect of sequential heat and cold shocks on nuclear phenotypes of the blood-sucking insect, Panstrongylus megistus (Burmeister) (Hemiptera, Reduviidae)

Thermal shocks induce changes in the nuclear phenotypes that correspond to survival (heterochromatin decondensation, nuclear fusion) or death (apoptosis, necrosis) responses in the Malpighian tubules of Panstrongylus megistus. Since thermal tolerance increased survival and molting rate in this species following sequential shocks, we investigated whether changes in nuclear phenotypes accompanied the insect survival response to sequential thermal shocks. Fifth instar nymphs were subjected to a single heat (35 or 40°C, 1 h) or cold (5 or 0°C, 1 h) shock and then subjected to a second shock for 12 h at 40 or 0°C, respectively, after 8, 18, 24 and 72 h at 28°C (control temperature). As with specimen survival, sequential heat and cold shocks induced changes in frequency of the mentioned nuclear phenotypes although their patterns differed. The heat shock tolerance involved decrease in apoptosis simultaneous to increase in cell survival responses. Sequential cold shocks did not involve cell/nuclear fusion and even elicited increase in necrosis with advancing time after shocks. The temperatures of 40 and 0ºC were more effective than the temperatures of 35 and 5ºC in eliciting the heat and cold shock tolerances, respectively, as shown by cytological analysis of the nuclear phenotypes. It is concluded that different sequential thermal shocks can trigger different mechanisms of cellular protection against stress in P. megistus, favoring the insect to adapt to various ecotopes.

Ripening and quality of 'Laetitia' plums following harvest and cold storage as affected by inhibition of ethylene action

The inhibition of ethylene action by 1-methylcyclopropene (1-MCP) extends shelf and storage life of many climacteric fruits. However, 1-MCP appears to have limited effects on stone fruit depending on specie and cultivar. The effects of 1-MCP on ripening and quality of 'Laetitia' plums were determined during ripening at 23ºC following harvest and cold storage. Japanese plums (Prunus salicina, cv. Laetitia) were harvested at mature pre-climacteric stage, cooled to 2ºC within 36 hours of harvest and then treated with 0, 0.05, 0.10, 0.50 or 1.00 muL L-1 of 1-MCP at 1°C for 24 hours. Following treatment, fruits were either held at 23ºC for 16 days or stored at 1ºC for 50 days. Fruits were removed from cold storage at 10-day intervals and allowed to ripe at 23°C for five days. A delay of climacteric respiration and ethylene production by 1-MCP treatment during ripening following harvest and cold storage was associated to a slow rate of fruit softening. 1-MCP treatment also delayed the loss of titratable acidity and changes of flesh and skin color, whereas it had little or no effect on soluble solids content. 1-MCP effects were concentration- and storage duration-dependent and, generally, a saturation fruit response to 1-MCP occurred between 0.5 and 1.0 muL L-1. During ripening, 1-MCP treated fruits attained quality similar to that of controls. Results indicated that 1-MCP treatment may extend shelf life (23ºC) and storage life (1ºC) of 'Laetitia' plums by approximately six and 20 days, respectively.

Emergence, longevity and fecundity of Trissolcus basalis and Telenomus podisi after cold storage in the pupal stage

Pupae of Trissolcus basalis (Wollaston) and Telenomus podisi Ashmead (Hymenoptera: Scelionidae) were stored at 12ºC and 15ºC for 120-210 days, after different periods of parasitism at 18ºC in order to evaluate adult emergence, longevity and ovipositional capacity. There was no emergence of adults at 12ºC. The rate of emergence of parasitoids transferred to 15ºC at the beginning of the pupal stage was 1.5% and 26.3%, for T. basalis and T. podisi respectively, whereas those parasitoids transferred one day before the expected date of emergence at 18ºC showed 86.4% of emergence for T. basalis and 59.9% for T. podisi. Mean adult longevity was also significantly lower when pupae were transferred to 15ºC at the beginning of the pupal stage. Females emerged after storage and maintained for 120 to 210 days at 15ºC parasitized host eggs after transference to 25ºC; however, fecundity of T. podisi was reduced in about 80% after cold storage.

Organic and total mercury determination in sediments by cold vapor atomic absorption spectrometry: methodology validation and uncertainty measurements

The purpose of the present study was to validate a method for organic Hg determination in sediment. The procedure for organic Hg was adapted from literature, where the organomercurial compounds were extracted with dichloromethane in acid medium and subsequent destruction of organic compounds by bromine chloride. Total Hg was performed according to 3051A USEPA methodology. Mercury quantification for both methodologies was then performed by CVAAS. Methodology validation was verified by analyzing certified reference materials for total Hg and methylmercury. The uncertainties for both methodologies were calculated. The quantification limit of 3.3 µg kg-1 was found for organic Hg by CVAAS.

Isomerization-cracking of n-octane on catalysts based on heteropolyacid H3Pw12O40 and heteropolyacid supported on zirconia and promoted with Pt and Cs

Isomerization - cracking of n-octane was studied using H3PW12O40 (HPA) and HPA supported on zirconia and promoted with Pt and Cs. The addition of Pt and Cs to the supported HPA did not modify the Keggin structure. The Pt addition to the supported HPA did not substantially modify the total acidity; however, the Brönsted acidity increased significantly. Cs increased the total acidity and Brönsted acidity. A linear relation was observed between the n-C8 total conversion and Brönsted acidity. The most adequate catalysts for performing isomerization and cracking to yield high research octane number (RON) are those with higher values of Brönsted acidity.

Parameter optimization of AC rectangular wave outputs for aluminum cold wire GTAW

The objective of this work was to optimize the parameter setup for GTAW of aluminum using an AC rectangular wave output and continuous feeding. A series of welds was carried-out in an industrial joint, with variation of the negative and positive current amplitude, the negative and positive duration time, the travel speed and the feeding speed. Another series was carried out to investigate the isolate effect of the negative duration time and travel speed. Bead geometry aspects were assessed, such as reinforcement, penetration, incomplete fusion and joint wall bridging. The results showed that currents at both polarities are remarkably more significant than the respective duration times. It was also shown that there is a straight relationship between welding speed and feeding speed and this relationship must be followed for obtaining sound beads. A very short positive duration time is enough for arc stability achievement and when the negative duration time is longer than 5 ms its effect on geometry appears. The possibility of optimizing the parameter selection, despite the high inter-correlation amongst them, was demonstrate through a computer program. An approach to reduce the number of variables in this process is also presented.

Fracture modes and acoustic emission characteristics of hydrogen-assisted cracking in high-strength low-alloy steel weldment

The aim of the present paper is to study the relationship between the fracture modes in hydrogen-assisted cracking (HAC) in microalloied steel and the emission of acoustic signals during the fracturing process. For this reason, a flux-cored arc weld (FCAW) was used in a high-strength low-alloy steel. The consumable used were the commercially available AWS E120T5-K4 and had a diameter of 1.6 mm. Two different shielding gases were used (CO2 and CO2+5% H2) to obtain complete phenomenon characterization. The implant test was applied with three levels of restriction stresses. An acoustic emission measurement system (AEMS) was coupled to the implant test apparatus. The output signal from the acoustic emission sensor was passed through an electronic amplifier and processed by a root mean square (RMS) voltage converter. Fracture surfaces were examined by scanning electron microscopy (SEM) and image analysis. Fracture modes were related with the intensity, the energy and the number of the peaks of the acoustic emission signal. The shielding gas CO2+5% H2 proved to be very useful in the experiments. Basically, three different fracture modes were identified in terms of fracture appearance: microvoid coalescence (MVC), intergranular (IG) and quasi-cleavage (QC). The results show that each mode of fracture presents a characteristic acoustic signal.

Application of the finite element method in cold forging processes

The demand for more efficient manufacturing processes has been increasing in the last few years. The cold forging process is presented as a possible solution, because it allows the production of parts with a good surface finish and with good mechanical properties. Nevertheless, the cold forming sequence design is very empirical and it is based on the designer experience. The computational modeling of each forming process stage by the finite element method can make the sequence design faster and more efficient, decreasing the use of conventional "trial and error" methods. In this study, the application of a commercial general finite element software - ANSYS - has been applied to model a forming operation. Models have been developed to simulate the ring compression test and to simulate a basic forming operation (upsetting) that is applied in most of the cold forging parts sequences. The simulated upsetting operation is one stage of the automotive starter parts manufacturing process. Experiments have been done to obtain the stress-strain material curve, the material flow during the simulated stage, and the required forming force. These experiments provided results used as numerical model input data and as validation of model results. The comparison between experiments and numerical results confirms the developed methodology potential on die filling prediction.

Pressure-assisted cold denaturation of hen egg white lysozyme: the influence of co-solvents probed by hydrogen exchange nuclear magnetic resonance

COSY proton nuclear magnetic resonance was used to measure the exchange rates of amide protons of hen egg white lysozyme (HEWL) in the pressure-assisted cold-denatured state and in the heat-denatured state. After dissolving lysozyme in deuterium oxide buffer, labile protons exchange for deuterons in such a way that exposed protons are substituted rapidly, whereas "protected" protons within structured parts of the protein are substituted slowly. The exchange rates k obs were determined for HEWL under heat treatment (80ºC) and under high pressure conditions at low temperature (3.75 kbar, -13ºC). Moreover, the influence of co-solvents (sorbitol, urea) on the exchange rate was examined under pressure-assisted cold denaturation conditions, and the corresponding protection factors, P, were determined. The exchange kinetics upon heat treatment was found to be a two-step process with initial slow exchange followed by a fast one, showing residual protection in the slow-exchange state and P-factors in the random-coil-like range for the final temperature-denatured state. Addition of sorbitol (500 mM) led to an increase of P-factors for the pressure-assisted cold denatured state, but not for the heat-denatured state. The presence of 2 M urea resulted in a drastic decrease of the P-factors of the pressure-assisted cold denatured state. For both types of co-solvents, the effect they exert appears to be cooperative, i.e., no particular regions within the protein can be identified with significantly diverse changes of P-factors.

Sensory profile of 'Douradão' peaches cold stored under controlled atmosphere

The sensory quality of 'Douradão' peaches cold stored in three different conditions of controlled atmosphere (CA1, CA2, CA3 and Control) was studied. After 14, 21 and 28 days of cold storage, samples were withdrawn from CA and kept for 4 days in ambient air for ripening. The sensory profile of the peaches and the descriptive terminology were developed by methodology based on the Quantitative Descriptive Analysis (QDA). The panelists consensually defined the sensory descriptors, their respective reference materials and the descriptive evaluation ballot. Fourteen panelists were selected based on their discrimination capacity and reproducibility. Seven descriptors were generated showing similarities and differences between samples. The data were analyzed by ANOVA, Tukey test and Principal Component Analysis (PCA). Results showed significant differences in the sensory profiles of the peaches. The PCA showed that CA2 and CA3 treatments were more characterized by the fresh peach flavor, fresh peach appearance, juiciness and flesh firmness, and were effective in keeping the good quality of the 'Douradão' peaches during the 28 days of cold storage. The Control and CA1 treatments were characterized by the mealiness and were ineffective for quality maintenance of the fruits during cold storage.

Determination of presence and quantification of cadmium, lead and copper in Nile tilapia (Oreochromis niloticus) fillets obtained from three cold storage plants in the state of Parana, Brazil

Pisciculture is an economic activity that is steadily growing in the state of Parana, Brazil, and Nile tilapia (Oreochromis niloticus) is one of the widely cultivated species in this state. Tilapia is not only a very nutritious food, but also an important indicator of environmental contamination. This study aimed to verify contamination by cadmium, copper and lead in tilapia fillets, and to compare the found values to international legislations. Were collected 135 samples of tilapia fillets, between July 2006 and May 2007, in three fish stores located in regions west and north of Paraná State. Samples of tilapia fillet were analyzed in relation to the presence of cadmiun, lead and copper, using atomic absorption spectrophotometry. Lead has not been detected in the analyses. Cadmium has been detected in three samples, on concentrations of 0.012 µg.g-1, 0.011 µg.g-1 and 0.014 µg.g-1. Copper has been detected in all fillets, and the average concentration of each cold storage plant was of 0.122 µg.g-1, 0.106 µg.g-1 and 0.153 µg.g-1. The concentrations found in this study are within the limits allowed by both the European and the Australian legislations.

Determination of some quality properties of marinated sea bream (Sparus Aurata L., 1758) during cold storage

In this study, it was aimed to determine the effect of sea bream (Sparus aurata) marinated some quality properties during cold storage. The fillets of fish were immersed into brine including 3.5% acetic acid 11% salt in the ratio of 1: 1.5 (fish: marinate brine) for marination process. After the process of ripening, samples were grouped into two and packed in plastic containers; one being plain (in sunflower oil) and the other being sauced (sauced prepared with sunflower oil). During storage, sensory, crude protein, lipid, dry matter and crude ash, TBA, TVB-N, TMA-N and peroxide analyses were done periodically. According to results of 200 days of storage, TVB-N values of sea bream marinates packaged as plain and sauced were 15.86/14.89 mg/100g, TBA 7.06/7.99 mg MA/kg, TMA-N 2.97/3.12, mg/100g, the value of peroxide was 7.23/7.45 meq/kg respectively. According to chemical and sensory analyses results obtained in the study; it was concluded that sea bream marinates packaged as plain and sauced can be stored in +4 °C for 200 days.

Microbiological and sensory evaluation of Jambu (Acmella oleracea L.) dried by cold air circulation

Abstract The aim of this study was to evaluate the microbiological and sensory quality of the Jambu (Acmella oleracea L.) in natura and dried by cold air, and the determination of its drying curve. The microbiological analysis were performed to Salmonella spp, the coagulase-positive Staphylococcus, and coliforms in the both Jambu samples, at 45 °C. Tacacá, the typical food dish of Pará state, Brazil, has showed good consumer global acceptance in the sensory evaluation of Jambu in natura (score of 8.00 ± 1.46) and dried (score of 8.67 ± 0.66). Both samples, Jambu in natura and dried by cold air, were by the current legislation regarding the microbiological aspects, this is the absence of Salmonella spp, coagulase-positive Staphylococcus <1×101 CFU/g, and coliforms <3 MPN/g, at 45 °C. Thus, considering sensory and health aspects, the commercialization of dried Jambu becomes viable, facilitating its transportation and handling, as well as for reducing its vegetable mass.