‘Sweet grape’ tomato post harvest packaging

ABSTRACT This paper aims at evaluating the shelf life of mini tomatoes (Lycopersicum esculentum Mill.) cultivar ‘Sweet Grape’, grown in hydroponics, and stored under environmental and refrigerated conditions inside different packages. We adopted a completely randomized design, in which treatments were combinations of storage conditions: environment (e) and refrigerated (r) with packaging: polyvinyl chloride film (PVC); low-density polyethylene (LDPE); biofilm of tomato fruit of Solanum lycocarpum A.St.-Hil (lobeira) (TFB); cassava starch biofilm (CSB); carnauba wax (Copernicia prunifera) (CW), and without packaging - control (C). Physicochemical and sensory tests were carried out at the beginning (day zero), and at 8, 19, and 33 days of storage (DS). Fruit stored inside PVCr, LDPEe, LDPEr, and CWr had an acceptable shelf life of 33 days. The use of cassava and tomato starches were not effective in controlling fruit fresh weight loss. ‘Sweet Grape’ tomato postharvest conservation was enhanced under refrigerated conditions. The sensory evaluation results revealed that CWr treatment most pleased appraisers, while PCV had the highest rejection rate.

Influence of chitosan addition on quality properties of vacuum-packaged pork sausages

The aim of the study was to evaluate the influence of the chitosan addition on the quality of vacuum packaged pork sausages. A variant of the product was elaborated with 1% (w/w) of chitosan in lactic acid solution at 1% (v/v) and it was compared to a control. Sausages were mechanically stuffed and manually conformed and vacuum packaged. Sausages were stored at 4 °C and microbiological evaluations, pH measurements, texture profile analysis and sensorial evaluation were performed. The chitosan addition in the formulation of the sausages did not reduce the microbiological counts. The pH values obtained in all samples were similar, which suggests that the chitosan addition did not influence the pH values of sausages. The added chitosan did not affect significantly (p < 0.05) the results of the texture profile analysis and sensorial attributes and therefore, the overall acceptance of the sausages.

Microstructural changes of frozen strawberries submitted to pre-treatments with additives and vacuum impregnation

Strawberries were submitted to freezing after pre-treatments with hydrocolloid and calcium salts (pectin and calcium chloride) at different concentrations, in the attempt to establish a correlation of the effects of these substances and their processing, on the physical and microstructural characteristics of fruits after thawing. Strawberry halves were submitted to impregnation with controlled vacuum pressure of 84.4, 50.5 and 16.6 kPa; comprising pectin at concentrations of 0, 1.5 and 3%; with the addition of calcium chloride at concentrations of 0, 3 and 6%; and glucose at 20%, for 4 hours. Measurements were made of the total soluble solid contents, cellular fluid loss, texture and viscosity of the solution, before and after the freezing/thawing. Images of the tissue cuts during the freezing, in function of time, were taken in an optic microscope coupled to a cold-stage and controlled temperature system, where the reduction of the cellular area was quantified using an image analyzing software. The pectin concentration had an influence on and demonstrated a potential for protection of the frozen tissue samples. The photomicrographs showed that the loss of cellular fluid occurs during the growth of ice formed in the intercellular spaces and it is retarded through treatments with high pectin concentrations.

Identification of fatty foods with contamination possibilities by plasticizers when stored in PVC film packaging

Poly-(vinyl chloride) (PVC) requires the addition of plasticizers - additives that give flexibility and malleability for its processing into flexible film. The most used ones are: di-(2-ethylhexyl) adipate (DEHA) and di-(2-ethylhexyl) phthalate (DEHP). Toxic effects of DEHP have been observed by several authors. Phthalates are being replaced by alternative substances in PVC flexible products, because of their possible toxicological effects. DEHA is a substitute for phthalates widely used as a plasticizer in PVC materials for involving food. Some authors have shown that the exposure to DEHA also induces toxicity. A cross-sectional study was performed to identify which fatty foods carry the possibility of contamination by DEHP and DEHA. Eighteen different foods with at least 3% (m/m) fat and the possibility of being wrapped in plastic film were determined. This study suggested that all foods were subject to contamination by DEHP and DEHA in those conditions - in decreasing consumption order of 96 to 22% in the convenience sample. New guidelines on the limits of DEHA and DEHP established by the Brazilian legislation, as additives in PVC film for packaging fatty food, are still relevant to ensure human health.

Guava Jam packaging determinant attributes in consumer buying decision

Using packaging and labels to lure consumers and to communicate product benefits directly on the shelf is a competitive advantage factor in the food industry sector. The label is especially effective since besides supplying basic details, such as weight, ingredients, and instructions in compliance with governmental regulations, it attracts consumers' attention and the desire to buy and which often becomes synonymous to the brand name. The objective of this study was to obtain detailed information on consumers' attitudes, opinions, behavior, and concepts regarding guava jam packaging using the focus group technique. The results showed that label color and design, packaging type and information, and brand name and price are determinant attributes in the consumers' decision to buy guava jam.

Influence of packaging and potassium sorbate on the physical, physicochemical and microbiological alterations of guava preserves

The elaboration of preserves through fruit processing is a promising alternative for their conservation. Such processing provides pleasant flavor due to the increase of sweetness and allows good conservation of the product for a prolonged time. Seeking quality and higher durability of fruit preserves, the purpose of this work was to evaluate the interference of potassium sorbate addition, and polypropylene, metallic and cellophane film packaging on the quality of guava (Psidium guajava L.) preserves during storage, through the physical, physiochemical and microbiological characteristics. The physical, physiochemical and microbiological analyses showed that the different types of packaging did not interfere in the stability of the guava preserves until the 5th month of storage - time being the factor that most influences the quality of the preserves when stored under temperature and humidity of 19.6 °C and 76.2%, respectively. The potassium sorbate caused an increase of the soluble solid levels and a decrease of the water activity. Regardless of the treatment, the preserves remained microbiologically stable during storage.

Integration of cooking and vacuum cooling of carrots in a same vessel

Cooked vegetables are commonly used in the preparation of ready-to-eat foods. The integration of cooking and cooling of carrots and vacuum cooling in a single vessel is described in this paper. The combination of different methods of cooking and vacuum cooling was investigated. Integrated processes of cooking and vacuum cooling in a same vessel enabled obtaining cooked and cooled carrots at the final temperature of 10 ºC, which is adequate for preparing ready-to-eat foods safely. When cooking and cooling steps were performed with the samples immersed in boiling water, the effective weight loss was approximately 3.6%. When the cooking step was performed with the samples in boiling water or steamed, and the vacuum cooling was applied after draining the boiling water, water loss ranged between 15 and 20%, which caused changes in the product texture. This problem can be solved with rehydration using a small amount of sterile cold water. The instrumental textural properties of carrots samples rehydrated at both vacuum and atmospheric conditions were very similar. Therefore, the integrated process of cooking and vacuum cooling of carrots in a single vessel is a feasible alternative for processing such kind of foods.

Effect of an edible crosslinked coating and two types of packaging on antioxidant capacity of castilla blackberries

In order to increase the shelf life and maintain the quality and stability of the biological compounds with antioxidant activity present in Castilla blackberry fruits, a sodium alginate-based edible crosslinked coating was applied, and the fruits were packed in two different plastic containers and stored under refrigeration (3 ± 1 °C). Total antioxidant capacity and its relationship to physicochemical variables such as pH, Brix, and acidity were evaluated in six treatments: uncoated blackberry stored in a macroperforated container (T1) and thermosealed container (T2), without crosslinked coating in a macroperforated container (T3) and thermosealed container (T4), with crosslinked coating (calcium ions) packed in macroperforated container (T5) and thermosealed container (T6). The results indicated that factors such as gas permeability in the coatings, the packaging used, and physicochemical parameters significantly affected the fruit total antioxidant capacity, with the highest level in T1 (0.22 µgEAA/ml) at the end of the essay, which is related to the lowest levels of pH and direct exposure to air. On the other hand, the lowest value was obtained in T6 (0.16 µgEAA/ml) due to the crosslinked coating, packaging in the thermosealed container, and higher pH value. Variations in acidity, Brix, and pH indicate the presence of degenerative processes in the crosslinked coating treatments, which limited the physicochemical changes.

Convective, vacuum and microwave drying kinetics of mallow leaves and comparison of color and ascorbic acid values of three drying methods

Mallow leaves (Malva sylvestris L.) with initial moisture of 5.02±0.003 on dry basis (82.5% on wet basis) were dried using three different drying methods, microwave, convective and vacuum. The leaves that weigh 75 g each were dried until their moisture fell down to 0.10±0.005 on dry basis (approximately 9% on wet basis). The following drying levels were used in each of the drying processes: 6.67, 8.67, 10, 11.33 W g-1 microwave power density; 50, 75, 100 and 125 °C for convective drying; and 3, 7 kPa at 50 and 75 °C for vacuum drying. Drying periods ranged from 6-10, 26-150 and 38-130 min. for microwave, convective and vacuum drying, respectively. Effective moisture diffisuvities ranged from 2.04403 10-10-3.63996 10-12 m2 s-1, 1.70182 10-11-1.10084 10-10 m2 s-1 and 1.85599 10-11-5.94559 10-10 m2 s-1 for microwave, convective and vacuum drying, respectively. According to ascorbic acid content and color parameters, the best microwave power density was found 10 W g-1 with a drying period of 6.5 min.

Forced-air, vacuum, and hydro precooling of cauliflower (Brassica oleracea L. var. botrytis cv. Freemont): part I. determination of precooling parameters

The aim of the present study was to precool cauliflower using forced-air, vacuum and high and low flow hydro cooling methods. The weight of the precooled cauliflower heads (5000±5 g) was measured before they were placed in standard plastic crates. Cauliflower heads, whose initial temperature was 23.5 ± 0.5 ºC, were cooled until the temperature reached at 1 ºC. During the precooling process, time-dependent temperature and energy consumption were measured, and during vacuum precooling, the decreasing pressure values were recorded, and a curve of time-dependent pressure decrease (vacuum) was built. The most suitable cooling method to precool cauliflower in terms of cooling time and energy consumption was vacuum, followed by the high and low flow hydro and forced-air precooling methods, respectively. The highest weight loss was observed in the vacuum precooling method, followed by the forced-air method. However, there was an increase in the weight of the cauliflower heads in the high and low flow hydro precooling method. The best colour and hardness values were found in the vacuum precooling method. Among all methods tested, the most suitable method to precool cauliflower in terms of cooling and quality parameters was the vacuum precooling method.

Forced-air, vacuum, and hydro precooling of cauliflower (Brassica oleracea L. var. botrytis cv. Freemont): Part II. Determination of quality parameters during storage

Cauliflower heads, which were precooled using four different methods including vacuum, forced-air, and high and low flow hydro precooling, were stored under controlled atmosphere and room conditions. Controlled atmosphere conditions (CA) were as follows: 1°C temperature, 90 ± 5% relative humidity, and 0:21 [(%CO2:%O2) – (0:21) control] atmosphere composition. Room conditions (RC) were: 22±1°C temperature and 55-60% humidity. Various quality parameters of the cauliflower heads were assessed during storage (days 0, 7, 14, 21, 28, and 35) under controlled atmosphere and room conditions (days 0, 5, and 10). During storage, weight loss, deterioration rate, overall sensory quality score, hardness, and colour (L, a, b, C and α) were evaluated. In the present study, the strength and quality parameters of cauliflower under CA and RC conditions were obtained. Vacuum precooling was found to be most suitable method before cauliflower was submitted to cold storage and sent to market. Furthermore, the storage of cauliflower without precooling resulted in a significant decrease in quality parameters.

Storage of Tabebuia caraiba (Mart.) Bureau seeds in different packaging and temperatures

Tabebuia caraiba (Mart.) Bureau, commonly known as Silver Trumpet Tree is a forestal species, belonging to Bignoniaceae family, which can be utilized as medicinal plant or in landscaping of urban and rural areas; besides producing large mechanical resistance wood. Despite its wide use and ecological importance, basic studies on storages of their seeds are scarce. This way, the objective of this study was to determine the most adequate packaging and the best temperatures, for storing seeds of T. caraiba. For this, seeds were stored in two types of packaging: Kraft paper bags and transparent polyethylene bags; which were then stored during 150 days under three different environments: laboratory normal environment (25±2 °C); cold chamber (8±2 °C); and refrigerator (6±2 °C). After periods of 0, 30, 60, 90, 120, and 150 days, seed moisture content, percentage of emergence, emergence speed index, and seedling length were evaluated. Seeds of T. caraiba kept in packaging of paper and polyethylene bags and stored at laboratory environmental condition, have lost more quickly their vigor along the storage period. For storage, it is recommended the maintenance of T. caraiba seeds in polyethylene bags into cold chamber; and/or polyethylene bags or Kraft paper bags into refrigerator.

Influence of the use of acids and films in post-harvest lychee conservation

Lychee (Litchi chinensis Sonn.) has a high commercial value; however, it has a short shelf-life because of its rapid pericarp browning. The objective of this study was to evaluate the shelf-life of 'Bengal' lychee fruits stored after treatment with hydrochloric acid and citric acid, associated with cassava starch and plastic packaging. Uniformly red pericarp fruits were submitted to treatments: 1-(immersion in citric acid 100 mM for 5 minutes + cassava starch 30 g L-1 for 5 minutes), 2-(immersion in hydrochloric acid 1 M for 2 minutes + starch cassava 30 g L-1 for 5 minutes), 3-(immersion in citric acid 100 mM for 5 minutes + polyvinyl chloride film (PVC, 14 µm thick)) and 4-(immersion in hydrochloric acid 1 M for 2 minutes + PVC film). During 20 days, the fruits were evaluated for mass loss, pericarp color, pH, soluble solids and titratable acidity, vitamin C of the pulp and pericarp and activities of polyphenol oxidase and peroxidase of the pericarp. The treatment with hydrochloric acid associated with PVC was the most effective in maintaining the red color of the pericarp for a period of 20 days and best preservation of the fruit. The cassava starch associated with citric acid, and hydrochloric acid did not reduce the mass loss and did not prevent the browning of lychee fruit pericarp.

Chemical treatment of papaya seeds aiming at long-term storage and control of damping off

Damping off is a nursery disease of great economic importance in papaya and seed treatment may be an effective measure to control. The aim of this work was to evaluate the quality of papaya seeds treated with fungicides and stored under two environmental and packaging conditions. Additionally, the efficiency of fungicide treatments in the control of damping-off caused by Rhizoctonia solani was evaluated. Papaya seeds were treated with the fungicides Captan, Tolylfluanid and the mixture Tolylfluanid + Captan (all commercial wettable powder formulations). Seeds of the control group were not treated. The seeds were stored for nine months in two conditions: packed in aluminum coated paper and kept at 7 ± 1ºC and in permeable kraft paper and kept in non-controlled environment. At the beginning of the storage and every three months the seed quality (germination and vigor tests), emergence rate index, height, dry mass and damping of plants in pre and post-emergence (in contaminated substrate and mycelia-free substrate) were analyzed. Both storage conditions as well as the fungicide treatments preserved the germination and seed vigor. In the infested substrate, seedling emergence was favored by fungicides, but in post-emergence, fungicides alone did not control the damping off caused by R. solani. Symptoms of damping off were not observed in the clean substrate. The results showed that the fungicide treatments may be used to pretreat papaya seed for long-term storage and commercialization.

Comparison of serum hepatitis B virus replication markers in patients with chronic hepatitis B: studies on HBeAg/Anti-HBe system, viral dna polymerase and HBV-DNA

The detection of HBV-DNA in serum by molecular hybridization is the most sensitive and specific marker of replication and infectivity of hepatitis B virus and currently is proposed as a routine diagnostic technique in the follow-up of HBV - related diseases. Comparing different techniques already described, we found that direct spotting of serum samples on nitrocellulose membranes under vacuum filtration, followed by denaturing and neutralizing washes is more practical, simple, sensible and reproducible. DNA polymerase assay using phosphonoformic acid as specific viral inhibitor has shown 86.8% of concordance with HBV-DNA detection, and so, it is an useful alternative in the follow-up of hepatitis B chronic patients. We found 19.2% HBeAg positive samples with no other markers of viral replication and no anti-HBe positive sample had detectable HBV-DNA. Discordance between the 2 systems have been extensively described, and we confirm this for the first time in our country. Molecular biological techniques are essential to determine the replication status of chronic hepatitis B patients.