Chemical characteristics and Kraft pulping of tension wood from Eucalyptus globulus labill

Tension (TW) and opposite wood (OW) of Eucalyptus globulus trees were analyzed for its chemical characteristics and Kraft pulp production. Lignin content was 16% lower and contained 32% more syringyl units in TW than in OW. The increase in syringyl units favoured the formation of β-O-4 bonds that was also higher in TW than in OW (84% vs. 64%, respectively). The effect of these wood features was evaluated in the production of Kraft pulps from both types of wood. At kappa number 16, Kraft pulps obtained from TW demanded less active alkali in delignification and presented slightly higher or similar pulp yield than pulps made with OW. Fiber length, coarseness and intrinsic viscosity were also higher in tension than in opposite pulps. When pulps where refined to 30°SR, TW pulps needed 18% more revolutions in the PFI mill to achieve the same beating degree than OW pulps. Strength properties (tensile, tear and burst indexes) were slightly higher or similar in tension as compared with opposite wood pulps. After an OD0(EO)D1 bleaching sequence, both pulps achieved up to 89% ISO brightness. Bleached pulps from TW presented higher viscosity and low amount of hexenuronic acids than pulps from OW. Results showed that TW presented high xylans and low lignin content that caused a decrease in alkali consumption, increase pulp strength properties and similar bleaching performance as compared with pulps from OW.

Performance of small wind turbines: simulation of electricity supply to loads connected to the public or isolated grid

ABSTRACT The successful in the implementation of wind turbines depends on several factors, including: the wind resource at the installation site, the equipment used, project acquisition and operational costs. In this paper, the production of electricity from two small wind turbines was compared through simulation using the computer software HOMER - a national model of 6kW and an imported one of 5kW. The wind resources in three different cities were considered: Campinas (SP/BR), Cubatão (São Paulo/BR) and Roscoe (Texas/ USA). A wind power system connected to the grid and a wind isolated system - batteries were evaluated. The results showed that the energy cost ($/kWh) is strongly dependent on the windmill characteristics and local wind resource. Regarding the isolated wind system – batteries, the full supply guarantee to the simulated electrical load is only achieved with a battery bank with many units and high number of wind turbines, due to the intermittency of wind power.

Performance of dairy heifers raised on Xaraés palissadgrass (Brachiaria brizantha cv. Xaraés) pasture supplemented with two types of mineral mixture

The effects of selective (e.g. mineral supplement formulated on the basis of nutritional and clinical examination of the herd) or commercial mineral supplementation of crossbred dairy heifers (Holstein-Mantiqueira), on daily weight gain (DWG), body condition score (BCS), age at first mating (AFM) and the intake of mineral mixture (IMM) managed on Xaraés palissadgrass pasture (Brachiaria brizantha cv. Xaraés) were evaluated from February 2006 to March 2008. Structural characteristics, forage allowance and nutritional value of Xaraés palissadgrass were also evaluated. The structural variables of pasture, allowances and nutritive value of forage, besides the DWG were only affected (p<0.05) by season, with highest results for spring and summer. Throughout the experimental period (730 days), no sign of mineral deficiency was detected in heifers that ingested the selective supplement. The DWG and AFM were not influenced by the mineral mixture offered (0.52 and 0.33 kg/day during the spring/summer and in fall/winter for DWG, respectively, and 813 days of AFM). The IMM was higher for commercial mineral mixture than for selective (61.6 and 51.0g/day respectively). The BCS was slightly higher for selective (3.17) than for the commercial (3.02) mineral mixture. Thus, the selective mineral supplement was a strategy to prevent mineral deficiency in this herd and resulted in similar performance at lower costs (e.g. due to less IMM) of crossbred heifers when compared with the commercial mineral supplementation.

Performance evaluation of 3D computer vision techniques

This work presents the implementation and comparison of three different techniques of three-dimensional computer vision as follows: • Stereo vision - correlation between two 2D images • Sensorial fusion - use of different sensors: camera 2D + ultrasound sensor (1D); • Structured light The computer vision techniques herein presented took into consideration the following characteristics: • Computational effort ( elapsed time for obtain the 3D information); • Influence of environmental conditions (noise due to a non uniform lighting, overlighting and shades); • The cost of the infrastructure for each technique; • Analysis of uncertainties, precision and accuracy. The option of using the Matlab software, version 5.1, for algorithm implementation of the three techniques was due to the simplicity of their commands, programming and debugging. Besides, this software is well known and used by the academic community, allowing the results of this work to be obtained and verified. Examples of three-dimensional vision applied to robotic assembling tasks ("pick-and-place") are presented.

The use of film coating on the performance of treated corn seed

The main objective of seed coating technology using polymers is to improve the physical, physiological and sanitary characteristics of seed performance. The objectives of the present study were to determine: the plantability of corn seeds treated with insecticide, fungicide and graphite, covered with a film coating; the dust retention on treated corn seeds; and the leaching of applied products on corn seeds covered by a film coating. Seed plantability was determined by counting the skips and double seeds; dust was determined by using fiberglass paper in mg.100 g-1 of seeds; and the leaching was determined by collecting the material leached in a 10 cm layer of sand after irrigation. The following conclusions were made: seeds covered with film coating effectively reduce skips and double seeds; film coating effectively reduces the formation of dust from the seeds; film coated seeds minimize the leaching of the insecticide applied in seed treatment; and there are differences in effectiveness related to film coating type and dosage.