Assessment of growth and yield performance of rubber tree clones of the IAC 500 series

The objective of this work was to evaluate the performance of 15 clones of the IAC 500 series of Hevea brasiliensis, developed at Instituto Agronômico (IAC), over a 12-year period, in the northwest region of São Paulo State, Brazil. The 15 new clones evaluated are primary clones obtained from selected ortets within half-sib progenies. The clone RRIM 600, of Malaysian origin, was used as the control. Dry rubber yield performance over a four-year period, mean girth at the tenth year, girth increment before and during tapping, thermal properties of the natural rubber produced and other characters of the laticiferous system were evaluated. Forty percent of the clones were superior in comparison to the control for yield. Clone IAC 500 recorded the highest yield (66.81 g per tree per tapping) over four years of tapping, followed by IAC 502 (62.37 g per tree per tapping), whereas the control recorded 48.71 g per tree per tapping. All selected clones were vigorous in growth. The natural rubber from this IAC clones showed thermal stability up to 300ºC. No differences were observed in the thermal behavior of rubber among the IAC series and the RRIM 600 clones. The clones IAC 500, IAC 501, IAC 502, IAC 503 and IAC 506 are the more promising for small-scale plantations, due to growth and yield potential.

Translocation of cyanogenic glycosides in rubber tree crown clones resistant to South American leaf blight

The objective of this work was to assess the possible transport of cyanogenic glycosides from leaves of rubber tree crown clones (Hevea spp.) resistant to South American leaf blight to the trunk of the panel clones in which they are grafted. The cyanogenic potential (HCNp) of the crown clones was determined in the trunk bark, at different distances from the cambium, and its gradient was evaluated along the trunk. The correlation between the HCNp of the crown leaves and that of the trunk bark was also evaluated. HCNp determined in leaves showed a wide range variation in the species studied as crown clones, with the lowest values registered in H. nitida clones, and the highest ones in H. rigidifolia. In the trunk bark, the tissue layer nearer the cambium showed higher HCNp values. A positive basipetal gradient was observed along the trunk, i.e., there was an increase in HCNp from the apex toward the base. Although the grafted crowns influence the cyanogenic potential of the trunk bark of panel clones, the absence of correlation between the HCNp of the leaves and trunk bark indicates that the crown is not the main source of the cyanogenic glycosides found in the trunk.

Genetic diversity of cultivated accessions and wild species of rubber tree using EST‑SSR markers

The objective of this work was to evaluate the efficiency of EST‑SSR markers in the assessment of the genetic diversity of rubber tree genotypes (Hevea brasiliensis) and to verify the transferability of these markers for wild species of Hevea. Forty‑five rubber tree accessions from the Instituto Agronômico (Campinas, SP, Brazil) and six wild species were used. Information provided by modified Roger's genetic distance were used to analyze EST‑SSR data. UPGMA clustering divided the samples into two major groups with high genetic differentiation, while the software Structure distributed the 51 clones into eight groups. A parallel could be established between both clustering analyses. The 30 polymorphic EST‑SSRs showed from two to ten alleles and were efficient in amplifying the six wild species. Functional EST‑SSR microsatellites are efficient in evaluating the genetic diversity among rubber tree clones and can be used to translate the genetic differences among cultivars and to fingerprint closely related materials. The accessions from the Instituto Agronômico show high genetic diversity. The EST‑SSR markers, developed from Hevea brasiliensis, show transferability and are able to amplify other species of Hevea.

Genetic parameters and estimated genetic gains in young rubber tree progenies

The objective of this work was to assess the genetic parameters and to estimate genetic gains in young rubber tree progenies. The experiments were carried out during three years, in a randomized block design, with six replicates and ten plants per plot, in three representative Hevea crop regions of the state of São Paulo, Brazil. Twenty-two progenies were evaluated, from three to five years old, for rubber yield and annual girth growth. Genetic gain was estimated with the multi-effect index (MEI). Selection by progenies means provided greater estimated genetic gain than selection based on individuals, since heritability values of progeny means were greater than the ones of individual heritability, for both evaluated variables, in all the assessment years. The selection of the three best progenies for rubber yield provided a selection gain of 1.28 g per plant. The genetic gains estimated with MEI using data from early assessments (from 3 to 5-year-old) were generally high for annual girth growth and rubber yield. The high genetic gains for annual girth growth in the first year of assessment indicate that progenies can be selected at the beginning of the breeding program. Population effective size was consistent with the three progenies selected, showing that they were not related and that the population genetic variability is ensured. Early selection with the genetic gains estimated by MEI can be made on rubber tree progenies.

Microclimate and development of 'Conilon' coffee intercropped with rubber trees

The objective of this work was to evaluate the influence of intercropping 'Conilon' coffee (Coffea canephora) with rubber trees on coffee tree microclimate, nutrition, growth, and yield. Rubber trees were planted in two double rows 33 m apart, with 4x2.3 m spacing between plants. Treatments consisted of the distances from the coffee plants to the rubber trees: 3, 6, 9, 12, and 15 m. Measurements of atmospheric variables (temperature, irradiance, and relative humidity), leaf nutrient concentration, internode length of plagiotropic and orthotropic branches, individual leaf area, chlorophyll content, and yield were performed. Intercropping promotes changes in the microclimatic conditions of coffee plants close to rubber trees, with reduction of temperature and irradiance level and increase in air relative humidity. The proximity of the coffee tree to the rubber trees promotes the elongation of the plagiotropic and orthotropic branches and increases the individual leaf area; however, it does not affect leaf concentrations of N, K, Mg, Fe, Zn, and B in 'Conilon' coffee and does not have a negative impact on yield.

Estudo comparativo entre bobinas de corpo e superfície na mamografia por ressonância magnética de próteses de silicone

Ressonância magnética de mamas de pacientes com próteses mamárias de silicone foi realizada utilizando-se parâmetros técnicos predeterminados, comparando-se bobina de superfície dedicada às mamas e bobina de corpo no mesmo grupo. Foram comparadas 43 próteses mamárias do tipo gel de silicone em 24 pacientes. Observou-se que a relação sinal-ruído obtida pela bobina de superfície foi maior que a obtida pela bobina de corpo. Dobras do elastômero foram identificadas com igual resolução pelas bobinas de superfície e de corpo em cerca de 82% à direita e 95% à esquerda. Apenas em cerca de 5% dos casos as dobras foram visibilizadas utilizando-se exclusivamente a bobina de superfície específica para mamas. Demonstrou-se que o sinal do "linguine" encontrado nas próteses é visto pelos dois métodos praticamente igual. Houve apenas um caso em que o sinal do "linguine" foi visto pela bobina de superfície e não pela bobina de corpo. Evidenciou-se também que boceladuras ou deformidade de contornos podem ser avaliadas com alta concordância, utilizando-se tanto a bobina de superfície quanto a bobina de corpo. Concluiu-se que, embora a qualidade da imagem seja melhor com o uso da bobina de superfície, próteses mamárias também poderão ser avaliadas pela bobina de corpo na ausência de uma bobina específica para mamas, com o mesmo resultado diagnóstico.

Desenvolvimento de sistemas líquido-cristalinos empregando silicone fluido de co-polímero glicol e poliéter funcional siloxano

For the construction of the phase diagrams, the method of the aqueous titration was used. There were prepared 5 ternary diagrams, varying the surfactant and the oil phase. The liquid-crystalline phases were identified by polarized light microscopy. The formulations prepared with silicon glycol copolymer, polyether functional siloxane (PFS) and water (S1) and with diisopropyl adipate, PFS and water (S4) presented liquid-crystalline phases with lamellar arrangement. Moreover, after 15 days in hot oven (37 ºC), the formulations presented hexagonal arrangement, evidencing the influence of the temperature in the organization of the system.

Líquidos iônicos como plastificantes em blendas de borracha nitrílica/polianilina

Two imidazolium-based ionic liquids (C4MIMTf2N and C4MIMBF4) were used to verify their influence on polyaniline (PANI) and nitrile rubber (NBR)/PANI blend properties and the vulcanization process. High conductivity values were observed for PANI-C4MIMTf2N samples and no interference was found for the C4MIMBF4 samples. These materials were added to NBR by mechanical mixing. Based on the torque results, the presence of C4MIMBF4 does not protect the vulcanization reaction of NBR with PANI as performed by C4MIMTf2N. The highest conductivity value was obtained with 7 wt. % of PANI-DSBA-C4MIMTf2N (10-6 S/cm). This result is attributed to the more effective interaction of PANI and NBR phases promoted by the ionic liquid.

Pathogenicity of Pratylenchus brachyurus to rubber rootstocks

The pathogenicity of Pratylenchus brachyurusto rubber (Hevea brasiliensis) rootstocks was studied in two experiments: 1) opencross seedlings of 'Tjir 1' x 'Tjir 16' were inoculated with zero, 7,700 or 23,100 nematodes per plant; 2) illegitimate seedlings of 'GT 1', 'RRIM 527' and 'RRIM 600' were inoculated with zero or 12,800 nematodes per plant. After 195 (1st experiment) or 105 days after inoculation (2nd experiment), P. brachyurusdid not affect the relative growth percentage in terms of plant height in both experiments but significantly diminished the stem diameter percentage and increased the stomatal resistance of 'GT 1' , 'RRIM 527' and 'RRIM 600'.

Optimization of invertase assay conditions in rubber tree plants (Hevea brasiliensis Muell. Arg.)

The objective of this work was to define the optimal conditions for invertase assay, seeking to determine the ideal parameters for the different isoenzymes of leaf and bark tissues in adult rubber trees. Assays of varying pH, sucrose concentration and temperature of the reaction medium were conducted for the two investigated isoenzymes. The results pointed out the existence of two different pH related isoforms for the two analyzed tissues, with an isoenzyme being more active at pH 5,5 and the other at neutral/alkaline pH. Leaf blade isoenzymes presented similar values for substrate concentration, whereas the bark isoenzyme presented maximum values below those previously reported. The assays at different temperatures presented similar values for leaf isoenzymes, though they have differed significantly among the obtained values.

Measurement and simulation of solar radiation availability in relation to the growth of coffee plants in an agroforestry system with rubber trees

Solar radiation is an important factor for plant growth, being its availability to understory crops strongly modified by trees in an Agroforestry System (AFS). Coffee trees (Coffea arabica - cv. Obatã IAC 1669-20) were planted at a 3.4 x 0.9 m spacing inside and aside rows of monocrops of 12 year-old rubber trees (Hevea spp.), in Piracicaba-SP, Brazil (22º42'30" S, 47º38'00" W - altitude: 546m). One-year-old coffee plants exposed to 25; 30; 35; 40; 45; 80; 90; 95 and 100% of the total solar radiation were evaluated according to its biophysical parameters of solar radiation interception and capture. The Goudriaan (1977) adapted by Bernardes et al. (1998) model for radiation attenuation fit well to the measured data. Coffee plants tolerate a decrease in solar radiation availability to 50% without undergoing a reduction on growth and LAI, which was approximately 2m².m-2 under this condition. Further reductions on the availability of solar radiation caused a reduction in LAI (1.5m².m-2), thus poor land cover and solar radiation interception, resulting in growth reduction.

Coffee water use in agroforestry system with rubber trees

Water uptake and use by plants are essentially energy processes that can be largely modified by percentage of soil cover, plant type; foliage area and its distribution; phenological stage and several environmental factors. Coffee trees (Coffea arabica - cv. Obatã IAC 1669-20) in Agrforestry System (AFS) spaced 3.4x0.9m apart, were planted inside and along rows of 12- year-old rubber trees (Hevea spp.) in Piracicaba-SP, Brazil (22 42'30" S, 47 38'00" W - altitude: 546m). Sap flow of one-year-old coffee plants exposed to 35; 45; 80; 95 and 100% of total solar radiation was estimated by the heat balance technique (Dynamax Inc.). Coffee plants under shade showed greater water loss per unit of incident irradiance. On the other hand, plants in monocrop (full sun) had the least water loss per unit of incident irradiance. For the evaluated positions average water use was (gH2O.m-2Leaf area.MJ-1): 64.71; 67.75; 25.89; 33.54; 27.11 in Dec./2002 and 97.14; 72.50; 40.70; 32.78; 26.13 in Feb./2003. This fact may be attributed to the higher stomata sensitivity of the coffee plants under more illuminated conditions, thus plants under full sun presented the highest water use efficiency. Express transpiration by leaf mass can be a means to access plant adaptation to the various environments, which is inaccessible when the approach is made by leaf area.

A importância do anel de silicone na derivação gástrica em Y-de-ROUX para o tratamento da obesidade

OBJETIVO: Analisaram prospectivamente pacientes obesos submetidos à derivação gástrica em y-de-roux com anel de silicone de diferentes tamanhos. MÉTODO: Os pacientes foram acompanhados durante cinco anos e através de exame endoscópico foram classificados em dois Grupos: anel com diâmetro interno até 10 mm (184 pacientes) e anel com diâmetro interno maior que 10 mm (107pacientes). Foi mensurada a porcentagem de perda do excesso de peso com um, dois e cinco anos de pós-operatório, e comparados os grupos entre si em cada ano da coleta dos dados. RESULTADOS: Houve maior emagrecimento no grupo com anel de diâmetro interno até 10 mm. A análise estatística mostrou que houve significância comparando-se os dois grupos entre si, um, dois e cinco anos após a cirurgia, sendo o emagrecimento sempre maior no grupo com anel de menor diâmetro. Não houve diferença estatisticamente significante ao se comparar outros dados da amostra como idade, sexo e IMC. CONCLUSÃO: A restrição determinada pelo anel aumenta a porcentagem de perda do excesso de peso.

Retalhos tubulares de pele de ratos com dois tipos de cateter de silicone

OBJETIVO: Avaliar o processo inflamatório e a fibrose em retalhos tubulares confeccionados na pele do dorso de ratos Wistar, moldados com cateteres de silicone com diferenças de resistência à compressão diametral. MÉTODO: Vinte ratos Wistar foram submetidos à confecção de três retalhos tubulizados de pele em região dorsal. Um retalho não foi moldado e os outros dois receberam, respectivamente, como molde interno, durante um período de sete dias, cateteres de silicone com diâmetros iguais e diferentes resistências à compressão diametral. Os animais foram divididos em dois grupos e sacrificados, respectivamente, no sétimo e vigésimo primeiro dia após a cirurgia. Realizou-se estudo histopatológico para a avaliação da fibrose e do processo inflamatório. RESULTADOS: Não foram encontradas diferenças significativas quanto à presença de fibrose ou processo inflamatório entre os três grupos estudados. CONCLUSÃO: A presença do cateter de silicone, independente de sua resistência à compressão diametral, não aumentou a intensidade da reação inflamatória e da fibrose nas margens suturadas de retalhos tubulares da pele de ratos Wistar.

Complicações locais após a injeção de silicone líquido industrial: série de casos

OBJETIVO: analisar uma série de casos de pacientes submetidos à injeção de silicone líquido industrial de maneira clandestina e por pessoas não habilitadas. MÉTODOS: análise retrospectiva de prontuários de pacientes atendidos no período de setembro de 2003 a dezembro de 2010. Foram avaliados: sexo, idade, local e volume de silicone injetado, tempo decorrido entre a aplicação e as manifestações clínicas, complicações, tratamento e evolução. Definiu-se como precoce as manifestações ocorridas até 30 dias da injeção e manifestações tardias após este período. RESULTADOS: Foram atendidos 12 pacientes, oito eram do sexo masculino, sendo sete transexuais. O volume injetado variou de 5ml a 2000ml, sendo desconhecido em três casos. Os locais mais frequentemente utilizados para injeção foram a região de coxas e glúteos. Oito casos apresentaram manifestações precoces, com quadros de inflamação e/ou infecção. Foi necessária a realização de desbridamento cirúrgico em cinco casos. Três pacientes com histórico de injeção na região mamária foram submetidas à adenomastectomia. Houve um óbito por quadro de choque séptico refratário. CONCLUSÃO: O uso do silicone líquido industrial deve ser totalmente contraindicado como material de preenchimento e modificação do contorno corporal, podendo apresentar graves complicações e até mesmo óbito.