Energetic efficiency of an agricultural tractor in function of tire inflation pressure

The tire inflation pressure, among other factors, determines the efficiency in which a tractor can exert traction. It was studied the effect of using two tire inflation pressures, 110.4 kPa in the front and rear wheels, 124.2 kPa in the front wheel and 138 kPa in the rear wheels, the energetic efficiency of an agricultural tractor of 147 kW of engine power, in the displacement speed of 6.0 km.h-1, on track with firm surface, with the tractor engine speed of 2000 rpm. For each condition of the tire pressure, the tested tractor was subjected to constant forces in the drawbar of 45 kN and 50 kN, covering 30 meters. It was used a randomized complete block with a 2x2 factorial arrangement (tire pressure and drawbar power) with four replications, totaling 16 experimental units. Data were subjected to analysis of variance, using the Tukey test at 5% probability for comparison averages. The lowest hourly and specific fuel consumption, the lowest slippage of the wheelsets and the highest efficiency in the drawbar was obtained with the tire inflation pressure of 110.4 kPa in the front and rear tires of the tractor, highlighting that lower pressures improve energetic and operational performance of the tractor.

Fragment size of corn silage according to the dry matter and forage harvester adjustments

In Brazil, the best results in milk production are found in the state of Paraná. Such results are reached through genetic selection of the animals and management of their diets, in which whole plant corn silage is widely used. Aiming the silage quality, it was evaluated the influence of dry matter content of the corn culture as forage and the harvester adjustments on the fragment size of whole plant corn silage. The fragment size of two corn hybrids silage (SPEED and 2B688) was evaluated using a 5x3 factorial, with 4 repetitions. The first factor was the harvest time of the plants (105, 108, 112, 118, and 123 days after sowing (DAS)), which determines the forage dry matter (DM) content. The second factor was the harvester adjustments (2, 6.5 and 11mm of theoretical fragment length (TFL)). The DM content did not affect the average fragment size of 2B688. For SPEED, however, the real fragment size decreased as the maturation of plants increased. The conclusion is that the DM content and harvester adjustments can affect the real fragment sizes, according to different plant genotypes. The alterations of the harvester adjustments resulted in different fragment sizes, however, it were different from those indicated by the manufacturer.

Modalities for soil preparation and gypsum application in ultisol: stem productivity of sugarcane

The study was conducted in an area of expansion of sugarcane at Vale do Paraná factory in Suzanápolis city - São Paulo (SP), in Brazil, in the northwestern region of the State of São Paulo. It was used the sugarcane variety RB92-5345, 1.5m of spacing between rows, in an Ultisol. The study aimed to evaluate the productivity of sugarcane and first ratoon and some soil chemical attributes in function of soil tillage and application or not of gypsum. The experimental design was randomized blocks with six treatments, in a factorial 3x2 and six replicates, the main treatments were soil tillage with three equipments, moldboard plow, chisel plow, and heavy harrow, and two secondary treatments with application of 1 t ha-1of gypsum and no gypsum. After each harvest of cane, the soil was characterized as to its fertility indicators in layers of 0.0-0.15; 0.15-0.30 and 0.30-0.45m. Differences in values of soil chemical attributes due to the methods of preparation occurred in the sugarcane did not last until the harvest of the 1st ratoon cane, and also did not influence the crop productivity. The gypsum application resulted in higher values ​​of total recoverable sugar (TRS) and the productivity of tons of stems per hectare (TSH) to sugarcane and 1st ratoon cane, respectively, confirming the initial hypothesis.

Evaluation of the effect of the seed extract of Moringa oleifera Lam over the efficiency of organic filters in wastewater treatment of dairy cattle breeding

This study aimed to evaluate the effect of Moringa oleifera Lam extract on the removal of total solids (TS), total suspended solids (TSS) and chemical oxygen demand (COD), in different filter media for treating wastewater of dairy cattle breeding (DCW). The moringa seed extract was obtained by grinding 50 g of seeds in one liter of distilled water and, after passing the solution through a quantitative paper filter of 25 microns, 60 mL of the extract were added to wastewater from cattle breeding before the filtration process in organic filters made of thin coal, bamboo leaves, eucalyptus leaves, gliricidia branches and sawdust. This was followed by the completely randomized experimental design, adopting a factorial of 5 x 2. Aliquots of filtered effluent were collected and the total solids (TS) concentrations, total suspended solids (TSS) and chemical oxygen demand (COD) were determined. It was found that the increase in the efficiency of removal of COD and total solids can be attributed to the coagulating power of the moringa seed extract, wherein the filter medium with bamboo leaves presented the best performance, showing potential for use as alternative filter material in the primary treatment of DCW.

Broiler breeder hen performance and egg hatchability during rainy season in Brazilian semi-arid region

Henhouse thermal comfort and bird age influence broiler breeder hen productivity; this way, the present research aimed to assess thermal comfort indexes and broiler breeder hen performance during winter in North East semi-arid region from Brazil, using a Cobb Avian 48 broiler strain at the age of 38 and 50 weeks. We measured the following bioclimatic indexes: air temperature and relative humidity, black globe temperature and humidity, CO2 concentration and sound pressure levels at henhouse facility. Data analysis design was complete randomized in a 3 x 3 factorial scheme with three treatments (months) and three replications (week number of collection by month). A number of 25 climatic data were observed. Bioclimatic indexes at the most warm hours throughout the day promoted bird discomfort yet sound pressure and carbon dioxide levels were under the Brazilian standards. Even in thermal comfort zone at some hours, the productivity indexes were in compliance with those recommended by the strain creation guidebook.

Sweet grape mini tomato grown in culture substrates and effluent with nutrient complementation

The objective of this study was to evaluate production of Sweet Grape mini tomato (Lycopersicum esculentum Mill.) using culture substrates and nutrient solution sewage effluent, applied by drip irrigation (fertigation). The experiment was conducted at the University of Goiás State (UEG-UnUCET), from June to November 2011 in Anápolis-GO, Brazil. The experimental design was a 2 x 3 factorial arrangement in a randomized complete block design with four repetitions. The plots were made by combining two nutrient solutions, effluent supplemented with mineral fertilizers (EcS); conventional nutrient solution (SnC); in addition three cultivation substrates: 60% of fine sand washed + 40% substrate composed by 20% coconut fiber plus 80% pine bark (S1); 20% coconut fiber and 80% pine bark (S2) and natural coconut fiber (S3). Sewage effluent were determined nitrate, calcium, potassium, manganese, total phosphate, total iron, magnesium, chloride, sulphate, boron, zinc and molybdenum. We evaluated average mass and average number of fruits per bunch, total fruit and total yield per plant. Statistical difference absence among tested solutions indicates sewage effluent can be used as an alternative source of nutrients in growing mini tomatoes in hydroponics.

Corn production for silage intercropped with forage in the farming-cattle breeding integration

Corn cropping for silage, due to the plant material exportation, intercropping with forage provides greater ground cover and straw formation for the Direct Planting System (DPS) continuity. The objective of this study was to evaluate corn production for silage in DPS intercropped with four forages (Urochloa brizantha cv. Marandu, U. ruziziensis cv. Ruziziensis, Panicum maximum cv. Tanzânia and P. maximum cv. Áries). We applied three sowing methods (in row together with corn fertilizer; by no-till sowing simultaneously to corn sowing and at V4 corn stage) and corn without intercropping. The experiment was conducted in autumn/ winter of 2010, in Selvíria - MS, in a randomized block design in factorial arrangement (4 x 3 + 1) and 4 replications. For corn, we evaluated plant height, basal stem diameter, initial and final stand and silage production and for forage dry matter production. Morphological characteristics and corn yield were not affected by intercropping when compared to sole corn crop. Forage dry matter production sown in corn row with fertilizer is a highlight, which in addition to providing greater productivity, harnesses the operation during sowing.

Determination of physical properties of crambe fruits during drying

The Knowledge of the physical properties of agricultural products has great importance for the construction and operation of equipment for drying and storage, to achieve increased efficiency in post-harvest operations. The aim was to determine and analyze the physical properties of crambe fruits during drying at different temperatures. Crambe fruits with an initial moisture content of 0.36 (decimal d.b.) which was reduced by drying at 37.0; 58.8 and 83.5 ºC and relative humidity of 29.4; 11.2 and 3.2%, respectively, to 0.09 ± 1 (decimal d.b.). At different levels of moisture contents (0.36; 0.31; 0.26; 0.21; 0.17; 0.13 and 0.09 decimal d.b.), was evaluated the intergranular porosity, the bulk density, the true density as well as the volumetric shrinkage and the fruit mass. The study was installed by the factorial 3 x 7, and three drying temperatures and seven moisture contents in a randomized design. Data were analyzed using regression. The bulk density and the true density decreases along the drying process; the volumetric shrinkage and the mass increased with lower moisture content and the intergranular porosity decreased sharply with the increasing drying temperature.

Evaluation of roof slope and exposure with different roofing materials in reduced models of animal production facilities in spring and summer

The present study was conducted at the Department of Rural Engineering and the Department of Animal Morphology and Physiology of FCAV/Unesp, Jaboticabal, SP, Brazil. The objective was to verify the influence of roof slope, exposure and roofing material on the internal temperature of reduced models of animal production facilities. For the development of the research, 48 reduced and dissemble models with dimensions 1.00 × 1.00 × 0.50 m were used. The roof was shed-type, and the models faced to the North or South directions, with 24 models for each side of exposure. Ceramic, galvanized-steel and fibro tiles were used to build the roofs. Slopes varied between 20, 30, 40 and 50% for the ceramic tile and 10, 30, 40 and 50% for the other two. Inside the models, temperature readings were performed at every hour, for 12 months. The results were evaluated in a general linear model in a nested 3 × 4 × 2 factorial arrangement, in which the effects of roofing material and exposure were nested on the factor Slope. Means were compared by the Tukey test at 5% of probability. After analyzing the data, we observed that with the increase in the slope and exposure to the South, there was a drop in the internal temperature within the model at the geographic coordinates of Jaboticabal city (SP/Brazil).

Environment in poultry production covered with thermal and aluminum roofing tiles

Brazil is a country of tropical climate, a fact that hinders the poultry production in the aspect of thermal comfort. Thus, we aimed to evaluate the thermal environment in commercial poultry houses with different covers during the months of December 2012 to May 2013, in the municipality of Rio Verde, Goiás. The experimental design was completely randomized in split plots with factorial arrangement of treatments 2x3, being two shed models (thermal and aluminum roof tiles) and three sections within each shed (initial, central and final) for 182 days, having the days as replicates. The thermal environment was assessed through thermal comfort indices: Temperature and Humidity Index, Black Globe Temperature and Humidity Index, Radiant Heat Load and Enthalpy. The data was analyzed by SISVAR 5.1., through the analysis of variance, the Scott Knott test used to compare the means, considering a significance level of 1%. The results showed a significant statistical difference between the sheds and the points assessed (P < 0.05). The thermal shed had the lowest values for the environmental variables (Dbt and Bgt) and thermal indices studied, but larger values for the RH compared to the shed with aluminum covering. The use of thermal covers minimizes the difference in temperature range throughout various times of the day, being at 14:00 o'clock the prominence time to others.

Chemical attributes of soil and dry mass accumulation of maize fertilized with cassava wastewater

The aim of this study was to evaluate chemical attributes alterations of a clay-loam textured soil and dry mass accumulation of maize submitted to application of cassava wastewater doses in three assessment periods. The experiment was conducted under greenhouse using a completely randomized experimental design in a factorial 5 × 3, with four replicates. The analyzed factors of research were doses of cassava wastewater (0; 12.6; 25.2; 50.4; 75.6 m3 ha-1) andassessment periods (20, 40 and 52 days after germination). The following parameters were determined: electric conductivity of soil saturation extract, pH in water, content of available P, content of exchangeable K+, Ca2+, Mg2+ and Na+of soil, dry mass of leaves and stem. The application of cassava wastewater on soil enables increase of pH, electric conductivity of saturation extract, contents of available P, contents of exchangeable K+ and Na+ and dry mass of leaves and stem. However, only pH and content of exchangeable K+ of soil, the electric conductivity of saturation extract and dry mass of leaves and stem are influenced by assessment period.

Effect of cycle time and airflow in biological nitrogen removal from poultry slaughterhouse wastewater using sequencing batch reactor

This study aimed to evaluate the influence of airflow (0.25, 0.50 and 0.75 L.L-1.min-1) and cycle time (10.45 h, 14.25 h and 17.35 h) on a sequencing batch reactor (SBR) performance in promoting nitrification and denitrification of poultry slaughterhouse wastewater. The operational stages included feeding, aerobic and anoxic reactions, sedimentation and discharge. SBR was operated in a laboratory scale with a working volume of 4 L, keeping 25% of biomass retained inside the reactor as inoculum for the next batch. In the anoxic stage, C: N ratio was maintained between 5 and 6 by adding cassava starch wastewater. A factorial design (22) with five repetitions was designed at the central point to evaluate the influence of cycle time and airflow on total inorganic nitrogen removal (N-NH4++N-NO2-+N-NO3-) and in the whole process (nitrification and denitrification). The highest total inorganic nitrogen removal (93.3%) was observed for airflow of 0.25 L.L-1.min‑1 and a cycle time of 14.25 h. At the end of the experiment, the sludge inside the reactor was characterized by fluorescent in situ hybridization (FISH), indicating the presence of ammonia and nitrite oxidizing bacteria.

Internal ambience of beehives Apis mellifera with different colors and roofing materials in the sub middle of the São Francisco Valley

ABSTRACTThe current study aimed to evaluate the influence of three colors and two types of roofing materials under the internal temperature of bee colonies Apis mellifera. The experiment was conducted at the Agricultural Sciences Campus at the Federal University of Sao Francisco Valley located in Petrolina-PE, in November and December 2013, using 24 colonies housed in Langstroth hives. The experiment was a completely randomized factorial design (3x2) with three colors of box (blue, white, and traditional) and two types of cover (with and without the use of plaster) with six treatments and four replications. The internal temperature dates of the colonies were hourly recorded, during 24 hours, and surface temperatures were hourly recorded between 08h00 and 17h00. The highest values for surface and internal temperature were registered in the blue painted boxes without the use of plasterboard, and the blue painted boxes covered with plasterboard respectively. However, the lowest values ​​were found in the white painted hives and hives that have not received the plasterboard. It is recommended to paint boxes with bright colors, and the use of plasterboard had no effect in reducing the internal temperature.

Genes associated with pathogenicity of avian Escherichia coli (APEC) isolated from respiratory cases of poultry

The virulence mechanisms of avian pathogenic Escherichia coli (APEC) have been continually studied and are believed to be multi-factorial. Certain properties are primarily associated with virulent samples and have been identified in avian isolates. In this study a total of 61 E. coli, isolates from chicken flocks with respiratory symptomatology, were probed by Polimerase Chain Reation (PCR) for the presence of genes responsible for the adhesion capacity, P fimbria (papC) e F11 fimbria (felA), colicin production (cvaC), aerobactin presence (iutA), serum resistance (iss), temperature-sensitive hemagglutinin (tsh), and presence of K1 and K5 capsular antigens (kpsII). The iss gene was detected in 73,8%, tsh in 55,7%, iutA in 45,9%, felA in 39,3%, papC in 24,3%, cvaC in 23% and kpsII in18%.

Metabolic profile and ruminal and abomasal pH in sheep subjected to intravenous ranitidine

Resumo: Brazilian sheep production has intensified, predisposing sheep to an increased incidence of digestive disorders, such as abomasal ulcers. Ranitidine is used to prevent and treat this disease; however, there is little information on the parenteral use of this drug in adult ruminants. Few data exist on the concomitant metabolic changes and the behavior of the digestive system associated with its use. For this study, five healthy male sheep with ruminal and abomasal cannulas were used. A 5x5 Latin square experiment with a 2x2+1 factorial arrangement of the treatments was performed. Sheep treated with drug doses of 1 or 2mg/kg ranitidine administered intravenously every 8 or 12 hours were compared with the control group, was treated intravenously with 1 mL of physiological solution per 25 kg every 12 hours. Higher total protein concentrations, hemoglobin levels, as well as increased aspartate aminotransferase activity and increased abomasal pH for up to 150 min following drug administration were observed in all animals that received the drug, regardless of dose and frequency. The animals treated every 12 hours showed a decrease in leukocyte number compared with the control group and with the animals treated every 8 hours. Increased serum creatinine concentrations were observed in the animals treated every 8 hours. Treatments of 1mg/kg every 8 hours and 2mg/kg every 12 hours increased the red blood cell count and decreased the serum pepsinogen. All protocols studied were safe for healthy sheep, but 1mg/kg ranitidine every 8 hours and 2mg/kg ranitidine every 12 hours were the most effective protocols for gastric protection.