New compositions of fluoroindate glasses with higher chemical resistance

In this paper, glasses in the systems In-Ba-Mg and In-Ba-Zn-Sr-Mg were water leachead at 80ºC showing surface degradation after 72 hours of leaching. The extent of such degradation is determined by the solubility and the concentration of the elemental fluorides that constitute the glasses. The formation of a layer of crystallized phases on the surface of the samples was observed. Small weight losses were registered and the absence of water on the glass matrix after the attack suggested that the use of MgF2 in the systems studied can lead to better results against moisture corrosion when compared to other fluoride glasses such as the fluorozirconates.

Corrosion resistance improvement of titanium base alloys

The corrosion resistance of the new Ti-6Al-4V-1Zr alloy in comparison with ternary Ti-6Al-4V alloy in Ringer-Brown solution and artificial Carter-Brugirard saliva of different pH values was studied. In Ringer-Brown solution, the new alloy presented an improvement of all electrochemical parameters due to the alloying with Zr; also, impedance spectra revealed better protective properties of its passive layer. In Carter-Brugirard artificial saliva, an increase of the passive film thickness was proved. Fluoride ions had a slight negative influence on the corrosion and ion release rates, without to affect the very good stability of the new Ti-6Al-4V-1Zr alloy.

Activity and sulfur resistance of Rh(I) and Pd(II) complexes

Two complexes of Rh(I) and Pd(II) with chloride and tridecylamine ligands were obtained and characterized by Elementary Analysis and by XPS and FTIR spectroscopies. Complexes anchored on γ-Al2O3 were tested in the styrene semi-hydrogenation reaction carried out in the absence or presence of a sulfur poison. Although both low loaded catalysts were highly selective, the Pd(II) complex was three times more active than the Rh(I) complex. The rhodium complex was more sulfur resistant but less active than the palladium complex. Differences in conversion and sulfur resistance between both complexes could be related to electronic and/or geometric effects.

Concepts in plant disease resistance

Resistance to nearly all pathogens occurs abundantly in our crops. Much of the resistance exploited by breeders is of the major gene type. Polygenic resistance, although used much less, is even more abundantly available. Many types of resistance are highly elusive, the pathogen apparently adapting very easily them. Other types of resistance, the so-called durable resistance, remain effective much longer. The elusive resistance is invariably of the monogenic type and usually of the hypersensitive type directed against specialised pathogens. Race-specificity is not the cause of elusive resistance but the consequence of it. Understanding acquired resistance may open interesting approaches to control pathogens. This is even truer for molecular techniques, which already represent an enourmously wide range of possibilities. Resistance obtained through transformation is often of the quantitative type and may be durable in most cases.

Cultural practices and genetic resistance as factors affecting soybean stem canker and plant yield in the Cerrado

Field experiments were conducted in the 1995-96 soybean (Glycine max) growing season to evaluate the effects of cultural practices and host genetic resistance on the intensity of soybean stem canker, caused by Diaporthe phaseolorum f.sp. meridionalis (Dpm). Experiments were conducted in a commercial field severely infected in the previous (1994-95) season. In one study, minimum tillage (MT) and no-tillage (NT) cropping systems were investigated for their effects on disease development and on plant yields in cvs. FT-Cristalina (susceptible) and FT-Seriema (moderately resistant). Another study evaluated the effects of plant densities (8, 15, 21 and 36 plants/m) on disease development in cvs. FT-Cristalina, FT-101 (moderately resistant) and FT-104 (resistant). Disease incidence and severity were consistently lower in NT than in MT, and plant yields were increased by 23% and 14% in the NT system for the susceptible and moderately resistant cultivars, respectively, compared to the yields in the MT system. The Gompertz and Logistic models described well the disease progress curves in all situations. For both susceptible and moderately resistant cultivars, disease severity increased proportionately to the increase in plant densities. At the end of the season, 100% of the plants of cv. FT-Cristalina were infected by Dpm, at all plant densities. Disease levels on cv. FT-101 were intermediate while only very low disease levels were recorded on cv. FT-104. There was a consistent negative correlation between stem canker severity and yield. Some practices demonstrated potential for direct application in disease control, and could be combined considering their additive effects.

Identification of rapd marker linked to blast resistance gene in a somaclone of rice cultivar Araguaia

The gene Pi-ar confers resistance to Pyricularia grisea race IB-45 in a somaclone derived from immature panicles of the susceptible rice (Oryza sativa) cultivar Araguaia. RAPD technique was used to identify molecular markers linked to this gene utilizing bulked segregant analysis. Initially, the two parental DNAs from the resistant donor SC09 and 'Araguaia' were analyzed using random primers. Of the 240 primers tested, 203 produced amplification products. The two parental DNAs along with the resistant and susceptible bulks of F2 population were screened using 48 primers that differentiated resistant and susceptible parents. Even though eight primers differentiated the resistant bulk from the susceptible bulk, as well as somaclone SC09 and 'Araguaia', only one primer, OPC02 ('GTGAGGCGTC'), was found to be tightly linked (1.7cM) to the resistance gene of somaclone SC09.

Expression of resistance in rice hybrids to Pyricularia grisea

Thirty-nine rice (Oryza sativa) hybrids and their restorers were assessed for vertical resistance to Pyricularia grisea in the rice blast nursery, and in artificial inoculation tests with two pathotypes, under controlled greenhouse conditions. The hybrids were developed from cytoplasmic genetic male sterile lines 046I and IR 58025A, derived from WA cytoplasm. In the rice blast nursery all hybrids showed susceptible reaction varying from 5 to 9. Compatible and incompatible leaf blast reactions of hybrids to two pathotypes, IC-1 and IB-45, were observed in inoculation tests. A majority of the hybrids were resistant when the restorer was resistant. However, seven of the 25 F1 hybrids exhibited susceptible reactions even when one of the parents was resistant to a pathotype. The partial resistance of 11 hybrids and their parents that showed compatible reactions to two pathotypes was analyzed. Differential interaction between isolates and genotypes was observed for partial resistance in relation to both disease severity and lesion number indicating the specific nature of partial resistance.

Genetic linkage map of Phaseolus vulgaris and identification of QTLs responsible for resistance to Xanthomonas axonopodis pv. phaseoli

Common bean (Phaseolus vulgaris) cultivars with a high degree of resistance to Xanthomonas axonopodis pv. phaseoli (Xap) are not available in Brazil. Despite many studies, a low degree of resistance to Xap continues to exist due to its complex genetic inheritance, which is not well known. The objectives of this research were to complement a common bean genetic map based on the cross between a susceptible genotype 'HAB-52' and a resistant genotype 'BAC-6', and to map and analyze genomic regions (quantitative trait loci – QTLs) related to Xap resistance. Eleven linkage groups were determined using 143 RAPD markers, covering 1,234.5 cM of the genome. This map was used to detect QTLs associated with Xap resistance on leaves and pods. The averages of disease severity on leaves (represented by the transformed disease index – TDI) and pods (represented by the diameter of lesion on pods – DLP) were added to the data of the linkage map. Five TDI QTLs and only one LDP QTL were detected. The TDI QTLs were placed in the A, B, G and J linkage groups, with phenotypic variations ranging from 12.7 to 71.6%. The DLP QTL explained 12.9% of the phenotypic variation and was mapped in a distinct linkage group. These results indicate that there are different genes involved in the control of resistance on leaves and pods.

Resistance spectra of wheat cultivars and virulence diversity of Magnaporthe grisea isolates in Brazil

Seventy-two monoconidial isolates of Magnaporthe grisea were obtained from the States of Mato Grosso do Sul and Paraná. The isolates were inoculated on seedlings of 20 wheat (Triticum aestivum) cultivars under greenhouse conditions. The virulence diversity of M. grisea was assessed based on compatible and incompatible reactions of leaf blast on wheat cultivars. Fifty-four distinct virulence patterns were identified on test cultivars among the isolates collected from the two wheat growing States. Sixteen of these isolates corresponding to 22.2% showed similar virulence pattern. None of the wheat cultivars was resistant to all isolates of M. grisea, but the cultivars differed in degree of resistance as measured by the relative spectrum of resistance (RSR) and disease index (DI). Among the cultivars the RSR ranged from 0 to 53.3% and DI from 0.4662 to 0.9662 (0 to 1 scale). The wheat cultivar BR18 exhibited a broad resistance spectrum in relation to the rest of the tested cultivars to the isolates of M. grisea, and can be used in wheat resistance breeding.

Identification of sources of resistance in sorghum to Peronosclerospora sorghi

The main objective of this work was to identify sources of resistance in sorghum (Sorghum bicolor) to Peronosclerospora sorghi, the causal agent of downy mildew, through the evaluation of 42 sorghum genotypes under natural infection in the field. Genotypes were planted in single row plots between two rows of the susceptible line SC283, planted 30 days before, to act as spreader rows, in two separate nurseries. The experimental design was a completely randomized block design with three replications. Sorghum genotypes CMSXS156, CMSXS157, CMSXS243, TxARG-1, 8902, 9902054, 9910032, 9910296, Tx430, QL-3, SC170-6-17, CMSXS762 and BR304 were classified as highly resistant in both nurseries. Among these, SC170-6-17 and 9910296 showed 0% systemic infection. Results indicated the possible occurrence of different pathotypes of P. sorghi in the two nurseries.

Evaluation of genetic mixtures of sorghum lines for anthracnose resistance management

The main objective of this work was to evaluate the diversification of sorghum (Sorghum bicolor) populations as a way to manage resistance to the sorghum anthracnose fungus Colletotrichum graminicola. A total of 18 three-way hybrids were obtained by crossing six single cross male-sterile F1 hybrids, derived by crossing A (non restorer sterile cytoplasm) and B (non restorer normal cytoplasm) lines, with three fertile R (restorer) lines, previously evaluated for their differential reaction to the pathogen. Variation in the level of resistance was observed, as indicated by the values of the area under the disease progress curve (AUDPC) obtained for each hybrid. Lines contributed differently to the level of resistance of each hybrid. All hybrids in which CMSXS169R was the male progenitor were classified as highly resistant. Some hybrids had a level of resistance superior to the maximum levels of each line component individually.

Resistance to Meloidogyne mayaguensis in Psidium spp. Accessions and their grafting compatibility with P. guajava cv. Paluma

Meloidogyne mayaguensis has been reported in some states of Brazil causing severe damage on commercial guava (Psidium guajava L.). Accessions of Psidium spp. were selected from a collection maintained in Embrapa Clima Temperado (Pelotas, Rio Grande do Sul State). Plants of different accessions were grown from seed in plastic bags and, when they reached 15-20 cm in height, were inoculated with 10,000 eggs/plant of M. mayaguensis. Eight months after inoculation, the different accessions were evaluated for resistance to M. mayaguensis. Three accessions of P. guajava were highly susceptible (RF=59.2) to this nematode. Psidium friedrichsthalianium was considered to be moderately resistant (RF=1.9). Three accessions of P. cattleyanum were immune to M. mayaguensis (RF = 0). When used as rootstocks P. cattleyanum and P. friedrichsthalianium were compatible with P. guajava cv. Paluma. Considering these results, the use of resistant rootstocks provides a promising control method for M. mayaguensis in commercial guava crop.

Evaluation of phenotypic stability of resistance to Phytophthora spp. in cacao clones

Resistance of fourteen Theobroma cacao clones to Phytophthora spp. was evaluated using stem inoculations on grafted seedlings. Concepts of phenotypic stability were used to interpret the results and to express horizontality of the resistance. The linear regression coefficient 'b', the determination coefficient (R²) and average lesion size were used to determine the level of horizontal resistance, the phenotypic stability and the predictability of all clones. The results indicated that clones P 7 and MA 15 present highest levels of horizontal resistance and stability, but with moderate predictability. Clones CAS 1 and CEPEC 13 were classified as those with high horizontal resistance, stability and predictability, while clones PA 30, UF 650 and SIAL 88 and EET 59 showed intermediate resistance and stability and high predictability. Clones SPA 17, OC 61, PA 150, SIAL 505, ICS 1 and R 41 presented high susceptibility and intermediate or low stability and moderate or high predictability.

Cotton resistance to ramulose and variability of Colletotrichum gossypii f. sp. cephalosporioides

Four cultivars and 21 lines of cotton were evaluated for resistance to ramulose (Colletotrichum gossypii f. sp. cephalosporioides) in a field where the disease is endemic. The seeds of each genotype were planted in 5 x 5 m plots with three replications. The lines CNPA 94-101 and 'CNPA Precoce 2'were used as standard susceptible and resistant references, respectively. The disease incidence (DI) was calculated from the proportion of diseased plants in the plot. The disease index (DIn) was calculated from the disease severity using a 1 to 9 scale, and was evaluated at weekly intervals starting 107 days after emergence. The data collected was used to calculate the area under disease progress curve (AUDPC). In general, the DIn increased linearly with time and varied from 20.0 to 57.1 and AUDPC from 567 to 1627 among the genotypes which could be clustered in to two distinct groups. The susceptible group contained two cultivars and nine lines and the resistant group contained one cultivar and 12 lines. The relationship between disease index and evaluation times was linear for the 25 genotypes tested. The line CNPA 94-101, used as susceptible standard, was the most susceptible with an average DI = 83.4, DIn = 57.1 and AUDPC = 1627.7. The line CNPA 96-08 with DI = 37.8, DIn = 20.0 and AUDPC = 567.7 was the most resistant one. Among the commercial cultivars 'IAC 22' was the most susceptible and 'CNPA Precoce 2', used as resistant standard was the most resistant. The variability in virulence of the pathogen was studied by spray inoculating nine genotypes with conidial suspensions (10(5)/mL) of either of the 10 isolates. The disease severity was evaluated 30 days later using a scale of 1 to 5. The virulence of the isolate was expressed by DIn. All the isolates were highly virulent but their virulence avaried for several genotypes and could be clustered in two distinct groups of less and more virulent isolates. The isolate MTRM 14 from Mato Grosso was the least virulent while Minas Gerais was the most virulent, with DIn of 6.36 and 46.47, respectively. In this experiment the line HR 102 and the cultivar 'Antares' were the most resistant ones with DIns of 18.32 and 19.14, respectively.