Viscosity of egg white from hens of different strains fed with commercial and natural additives

Yolk color and egg white (albumen) cleanliness and viscosity are important parameters by which consumers judge the quality of eggs. This study aimed to investigate changes in albumen viscosity during storage of eggs for up to 36 days from two different commercial laying hen strains (Carijo Barbada and Isa Brown) fed a diet containing annatto (1.5 and 2.0%) or a synthetic additive without synthetic colorants (control). Analyses of humidity, albumen height, pH, viscosity, foam formation, and stability were carried out on eggs. Carijo Barbada strain had smaller albumen, lower humidity and higher egg white viscosity than Isa Brown strain; however, with storage, viscosity lowered significantly on both strains. Initially, the addition of 2.0% of annatto or a synthetic additive increased viscosity in both strains, but with storage only the control maintained longer viscosity. Lower viscosity did not change foam density and stability.

Adzuki beans (Vigna angularis) seed quality under several drying conditions

This study analyzed the drying process and the seed quality of adzuki beans (Vigna angularis). Grains of adzuki beans, with moisture content of 1.14 (decimal dry basis) at harvest and dried until the moisture content of 0.11 (decimal dry basis.) were used. Drying was done in an experimental drier maintened at controlled temperatures of 30, 40, 50, 60, and 70 ºC and relative humidity of 52.0, 28.0, 19.1, 13.1, and 6.8%, respectively. Physiological and technological seed quality was evaluated using the germination test, Index of Germination Velocity (IGV), electrical conductivity, and water absorption, respectively. Under the conditions tested in the present study, it can be concluded that drying time for adzuki beans decreases with the higher air temperatures of 60 and 70 ºC, and it affected the physiological and technological seed quality. Thus, to avoid compromising adzuki seeds quality, it is recommended to promote its drying up to 50 ºC.

Sugar fractionation and pectin content during the ripening of guava cv. Pedro Sato

Guava is one of the most complete and balanced fruits in in terms of s nutritional value. Highly perishable, due to its intense metabolism during ripening, its shelf life can reach 3 to 5 days under room temperature. The firmness of the green and mature fruits is due mainly to the pectin polymers. The loss of firmness during the guava ripening is due to hydrolytic enzyme activity, which promotes intense solubilization of the cell wall pectins. Given the above, with the purpose of trying to explain the rapid firmness decrease, the centesimal composition and sugar fraction of the guava fruit were determined during ripening at room temperature. The guavas were picked at the half-mature stage and stored for 8 days at 22 ± 1 ºC and 78 ± 1% relative humidity. The analyses conducted were: centesimal composition, sugar fractionation, and infrared absorption spectrometry. The results showed that the guava sugars did not vary during ripening. The estimated pectin levels (5.7%) were higher than those mentioned in the literature (2.4%), which can better explain the role of the pectin in the fruit firmness.

Ripening pattern of guava cv. Pedro Sato

Guava is a fruit with high respiration rates and a very short shelf life. Since information on its respiration pattern is contradictory, the objective was to study the changes occurring in the fruit during ripening and to relate them to the respiration behavior of this fruit. Guavas were picked at the half-ripe stage and stored for 8 days at 22 ± 1 ºC and 78 ± 1% relative humidity. The analyses conducted were: peel and pulp coloration, firmness, total soluble solids (TSS), total titratable acidity (TTA), and ethylene production. According to the results, it was verified that the parameters analyzed apparently do not coincide and are ethylene-independent. There was an accentuated ethylene production during ripening, starting from the 4th day. The ethylene synthesis continued increasing up to the 8th day, when the fruits were already decomposing. It was observed that the firmness decreased sharply in the first three days of ripening, and the skin and pulp color changed during ripening. The TSS, total soluble solids, and the TTA, total titratable acidity, practically did not change during the ripening, even with the increased ethylene production. It can be concluded that guava is a fruit that presents characteristics of climacteric and non-climacteric fruits.

Reduction of carcass weight loss in swines

The carcass fast freezing is one of the aspects of great prominence to the final quality of pork. In order to reduce weight loss, two experiments were performed, in which the carcasses were monitored during 20 hours to evaluate the main variables involved during two different freezing processes (standard and proposed) as follows: microbiological quality, storage temperature, relative humidity (RH) and air velocity. In experiment I, the carcasses were submitted to a system using heat shock (2 hours in static tunnel at - 25 °C) and subsequently sent to the equalization chamber. In experiment II, the carcasses were submitted to the heat shock and stored in a chamber with RH between 80-85%. The chambers used in both experiments showed no change in the variables studied (internal temperature of 5 °C and air velocity of approximately 0.3 m/s). However, the relative humidity in the three chambers was evaluated and significant differences were found; as a consequence, high levels of weight loss were observed in both chambers In experiment II there was an increase of RH, which reduced the weight loss of the carcasses.

Sensory quality attributes of lettuce obtained using different harvesting performance systems

The objective of this study was to determine the best lettuce cultivar (American 'Graciosa', 'Vanda', 'Marcela' and 'Lavínia') harvesting method. Therefore, quality and shelf-life were evaluated using sensory analyses. Lettuce heads was harvested with the root on by the producer, so that they were cut in different ways in the laboratory. The samples were stored in a cold chamber at 10 °C and 80% ± 2% of relative humidity for nine days, and the sensorial analyses were performed according to Qualitative Descriptive Analysis method on days 1, 3, 6, and 9 of storage by twelve trained testers. The results were evaluated by variance analysis, principal component analysis, and the Tukey test with a reliability of 95%. The results indicate that there was a reduction in the quality of lettuce between the 1st and the 5th day of storage and that after the sixth day of storage the lettuce samples were considered unfit for consumption, except for the 'Lavínia' lettuce cultivar with root and cut treatment 2. On the ninth day of storage all samples were considered inappropriate for consumption.

Physicochemical and microbiological quality of raspberries (Rubus idaeus) treated with different doses of gamma irradiation

This study was conducted to evaluate the physicochemical and microbiological characteristics of raspberries exposed to different radiation doses. The fruits were harvested in the city of Campestre, MG, packed in polyethylene bags, and transported to the Federal University of Lavras (UFLA), where they were separated into 4 lots. Irradiation was performed at the Center for Development of Nuclear Technology in Belo Horizonte, MG. The doses used were 0 (control), 0.5, 1.0, and 2.0 kGy. After irradiation, the fruits were transported back to UFLA and stored at 1 ºC and 95% relative humidity (RH) for 12 days. The physicochemical analyses for mass loss, total soluble solids, titratable acidity, pH, total soluble sugars, total soluble pectin, firmness, vitamin C content, total antioxidant activity, and total phenolic, and the microbiological assays (coliform at 35 and 45 ºC, psychrotrophic and filamentous fungi and yeasts) were performed after 0, 3, 6, 9, and 12 days of storage. Lower loss of mass and filamentous fungi and yeast count were observed in the irradiated fruits, and 2 kGy was determined as the most effective dose for microbial control, but this irradiation dose also resulted in increased loss of fruit firmness.

Physicochemical and microbiological parameters of dried salted pork meat with different sodium chloride levels

The objective of this study was to evaluate the physicochemical and microbiological parameters of pork meat submitted to dry salting. Sodium chloride (NaCl) was added at levels of 0%, 2.5%, 5%, 7.5% or 10% by the meat weight. Dry salting technique was used, which consists of rubbing the sodium chloride manually, followed by a rest period. The data were submitted to analysis of variance using a completely randomized experimental design. The means were compared by Duncan test at 5%. The salting process reduced (P < 0.05) humidity and water activity, and it increased (P < 0.05) ash, chloride, palmitic acid, and water holding capacity levels compared to those of the control. Luminosity (L*) was lower (P < 0.05) in the control, and a* color was more intense in samples with 2.5% NaCl. Cooking loss was lower (P < 0.05) in the samples salted with 5% and 10% NaCl, and similarity was observed between the levels 0 and 7.5% salt. The treatments with levels 0% and 2.5% NaCl had higher mesophilic counts. The other microbiological parameters were within limits established by law. Therefore, salting with 5% NaCl can be used in pork meat in order to maintain the physicochemical and microbiological characteristics of the final product.

Characterization of spoilage bacteria in pork sausage by PCR-DGGE analysis

To investigate microbial diversity and identify spoilage bacteria in fresh pork sausages during storage, twelve industrial pork sausages of different trademarks were stored at 4 ºC for 0, 14, 28 and 42 days, 80% relative humidity and packaged in sterile plastic bags. Microbiological analysis was performed. The pH and water activity (a w) were measured. The culture-independent method performed was the Polymerase Chain Reaction - Denaturing Gradient Gel Electrophoresis (PCR-DGGE). The culture-dependent method showed that the populations of mesophilic bacteria and Lactic Acid Bacteria (LAB) increased linearly over storage time. At the end of the storage time, the average population of microorganisms was detected, in general, at the level of 5 log cfu g-1. A significant (P < 0.005) increase was observed in pH and a w values at the end of the storage time. The PCR-DGGE allowed a rapid identification of dominant communities present in sausages. PCR-DGGE discriminated 15 species and seven genera of bacteria that frequently constitute the microbiota in sausage products. The most frequent spoilage bacteria identified in the sausages were Lactobacillus sakei and Brochothrix thermosphacta. The identification of dominant communities present in fresh pork sausages can help in the choice of the most effective preservation method for extending the product shelf-life.

Mathematical modeling of microwave dried celery leaves and determination of the effective moisture diffusivities and activation energy

Celery (Apium graveolens L. var. secalinum Alef) leaves with 50±0.07 g weight and 91.75±0.15% humidity (~11.21 db) were dried using 8 different microwave power densities ranging between 1.8-20 W g-1, until the humidity fell down to 8.95±0.23% (~0.1 db). Microwave drying processes were completed between 5.5 and 77 min depending on the microwave power densities. In this study, measured values were compared with predicted values obtained from twenty thin layer drying theoretical, semi-empirical and empirical equations with a new thin layer drying equation. Within applied microwave power density; models whose coefficient and correlation (R²) values are highest were chosen as the best models. Weibull distribution model gave the most suitable predictions at all power density. At increasing microwave power densities, the effective moisture diffusivity values ranged from 1.595 10-10 to 6.377 10-12 m2 s-1. The activation energy was calculated using an exponential expression based on Arrhenius equation. The linear relationship between the drying rate constant and effective moisture diffusivity gave the best fit.

Forced-air, vacuum, and hydro precooling of cauliflower (Brassica oleracea L. var. botrytis cv. Freemont): Part II. Determination of quality parameters during storage

Cauliflower heads, which were precooled using four different methods including vacuum, forced-air, and high and low flow hydro precooling, were stored under controlled atmosphere and room conditions. Controlled atmosphere conditions (CA) were as follows: 1°C temperature, 90 ± 5% relative humidity, and 0:21 [(%CO2:%O2) – (0:21) control] atmosphere composition. Room conditions (RC) were: 22±1°C temperature and 55-60% humidity. Various quality parameters of the cauliflower heads were assessed during storage (days 0, 7, 14, 21, 28, and 35) under controlled atmosphere and room conditions (days 0, 5, and 10). During storage, weight loss, deterioration rate, overall sensory quality score, hardness, and colour (L, a, b, C and α) were evaluated. In the present study, the strength and quality parameters of cauliflower under CA and RC conditions were obtained. Vacuum precooling was found to be most suitable method before cauliflower was submitted to cold storage and sent to market. Furthermore, the storage of cauliflower without precooling resulted in a significant decrease in quality parameters.

Influence of the moisture at harvest and drying process of the grains on the level of carotenoids in maize (Zea mays)

AbstractMaize is considered a source of carotenoids; however, these compounds are highly unstable, degraded by high temperatures, exposure to light and presence of oxygen. The objective of this work was to evaluate the influence of the moisture and type of drying applied to grains on the level of carotenoids in yellow maize. The experiment was conducted in a completely randomized design (2 × 4 factorial), two levels of initial moisture at the harvest (22 and 19%) and three types of drying (in the sun; in the shade and in a dryer) and control (no drying). The samples of grains after drying with 12% of final moisture were analyzed by concentration of total carotenoids, carotenes (α-carotene + β-carotene), monohydroxilated carotenoids (β-cryptoxanthin), and xanthophylls (lutein + zeaxanthin). Initial moisture, type of drying and the interaction between moisture versus drying influence (p≤0.05) the levels of carotenoids in grains. This is the first report about the drying conditions and harvest’s initial moisture as influence on the profile and content of carotenoids in maize grains. Based on the results, this work suggested that the harvest be carried out preferably when the grains present 22% humidity, with drying in a dryer or in shade for further use or storage.

Effect of different proportions of brea gum in the functional characteristics of wheat flour starch: impact on the physical quality of bread

The aim of this work was to study the changes induced by BG in the behaviour of wheat starch, and observe the influence of these variations on the quality of a basic white bread. The effect of four BG addition levels in the wheat flour functional characteristics (WAI, WSI, and pasting properties) and bread quality (physical parameters, crumb grain structure, moisture and hardness) was investigated. The highest levels of BG (1% and 2%) decreased the peak viscosity, and increased the stability and setback of the flour. This was due to a lower gelatinization of the starch granules, caused by a competition for water between the hydrocolloid and starch. These changes influenced the bread quality. The loaves added with 1% and 2% of BG presented smaller alveoli: this resulted in more compact, hard and less airy crumbs. Nevertheless, the moisture of the samples at 1% and 2% of added gum was higher than the control bread. However, the incorporation of BG at 0.5% did not affect the pasting parameters and bread quality, but increased moisture of crumb, so this concentration would be most recommended for baking, since higher humidity could favour the shelf- life of the product.

Variation of some chemical and functional properties of Bambara groundnut (Voandzeia Subterranean L. Thouars) during sort time storage

Abstract The storage susceptibility of Bambara groundnut (B. G.) (Voandzeia Subterranean (L.) Thouars) to Callosobruchus maculatus and chemical and functional properties of 11 varieties form Far-North of Cameroon were investigate using standard analytical methods. Storage susceptibility shown that, after five months within treatment, C. maculatus destroy 10 to 50% of grains. The chemical characteristics of none attack grains of 11 varieties were range to 18.64 at 21.08%, 6.85 at 7.44%, 49.75 at 52.68% and to 6.05 at 7.55% respectively for protein, fat, starch and free carbohydrate. These chemical characteristics significantly (p < 0.05) decreases form attacks varieties. For the functional parameters, the none attacks grains was range of 130 at 135%, 19.15 at 20.91%, 18.20 at 21.13%, 2.76 at 3.21% and of 8.54 at 10.14% respectively for water capacity absorption, solubility index, gel length, ash and humidity. The results of this study indicated that storage susceptibility, chemical and functional properties of B. G. be dependant to the varieties.

The effect of different concentrations of pre-harvest gibberellic acid on the quality and durability of ‘Obilnaja’ and ‘Black Star’ plum varieties

Abstract The research work aimed at investigating the effect of pre-harvest gibberellic acid (GA3) treatment on the quality of ‘Obilnaja’ and ‘Black Star’ Japanese plum varieties. GA3 was sprayed onto the trees during the fruit color break at 0, 25, 50, 75, and 100 ppm concentrations. After pre-cooling, the plums were placed in modified atmosphere packages and exposed to the following conditions as follows: short storage-transportation (ST) [20 days at 2 °C and 90% relative humidity (RH)]; distribution center (DC) (5 days at 6 °C and 80% RH), and shelf life conditions (SL) (2 days at 20 °C and 70% RH). Pre-harvest GA3 treatments increased the fruit weight and size. Treatment of GA3 at 50, 75, and 100 ppm increased the fruit flesh firmness and total soluble substances (TSS) values in both the plum varieties during storage, transport, and marketing; it also limited the weight loss during the marketing process. Treatment of GA3 had no significant effects on the color, titratable acidity (TA), and the total phenolic and antioxidant activity values of plums. Pre-harvest GA3 treatment at 50 ppm GA3 can be thus recommended for both the plum varieties due to its effect on the fruit quality.