Characterization and treatment of sisal fiber residues for cement-based composite application

Sisal fiber is an important agricultural product used in the manufacture of ropes, rugs and also as a reinforcement of polymeric or cement-based composites. However, during the fiber production process a large amount of residues is generated which currently have a low potential for commercial use. The aim of this study is to characterize the agricultural residues by the production and improvement of sisal fiber, called field bush and refugo and verify the potentiality of their use in the reinforcement of cement-based composites. The residues were treated with wet-dry cycles and evaluated using tensile testing of fibers, scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. Compatibility with the cement-based matrix was evaluated through the fiber pull-out test and flexural test in composites reinforced with 2 % of sisal residues. The results indicate that the use of treated residue allows the production of composites with good mechanical properties that are superior to the traditional composites reinforced with natural sisal fibers.

Microencapsulation of pequi pulp by spray drying: use of modified starches as encapsulating agent

The aim of this study was to evaluate the microencapsulation of pequi pulp by spray drying. A central composite rotational design was used in order to evaluate the effect of the independent variables: inlet air temperature, surfactant concentration and modified starch concentration. The dependent variables were assumed as yield of the process and the product features microencapsulated. A selection of the best process condition was performed to obtain the best condition of a product with the highest vitamin C and carotenoids content. Powders showed moisture content below 2%. The experimental values of hygroscopicity, yield, water activity, total carotenoids and vitamin C powders ranged from 7.96 to 10.67 g of adsorbed water/100g of solids, 24.34 to 49.80%, 0.13 to 0.30, 145.78 to 292.11 mg of ascorbic acid/g of pequi solids and 15.51 to 123.42 mg of carotenoids/g of pequi solids, respectively. The inlet air temperature 140°C, the surfactant concentration of 2.5% and the modified starch concentration of 22.5% was recommended as the selected condition. By the scanning electron microscopy, it was observed that most of the particles had spherical shape and smooth surface.

The materno-fetal interface in llama (Lama guanicoe glama)

Samples from 9 llamas (28 through 36 weeks of gestation) were collected and fixed in 4% buffered paraformaldehyde (light microscopy) and in 2.5% buffered glutaraldehyde (transmission and scanning electron microscopy). The material was processed in paraplast and slides (5mm) were stained with HE, PAS, Masson-Trichrome, acid phosphatase and Perl's. The uteroferrin was immunolocalized. The results show that llama placenta is chorioallantoic, diffuse, folded and epitheliochorial, and the fetus is covered with an epidermal membrane. The trophoblast cells have variable morphology: cubic, rounded and triangular cells, with cytoplasm containing PAS-positive granules. Binucleated cells with large cytoplasm and rounded nuclei, as well as giant trophoblastic cells with multiple nuclei were also observed. Numerous blood vessels were observed beneath the cells of the uterine epithelium and around the chorionic subdivided branches. Glandular activity was shown by PAS, Perl's, and acid phosphatase positive reactions in the cytoplasm and glandular lumen, and by immunolocalization of the uteroferrin in the glandular epithelium. The uterine glands open in spaces formed by the areoles, which are filled by PAS-positive material. The llama fetus was covered by the epidermal membrane, composed of stratified epithelium, with up to seven layers of mono-, bi- or trinucleated cells. The high level of maternal and fetal vascularization surfaces indicates an intense exchange of substances across both surfaces. The metabolic activity shown in the uterine glands suggests an adaptation of the gestation to the high altitudes of the natural habitat of this species.

Turgida turgida (Nematoda: Physalopteridae) parasitic in white-bellied opossum, Didelphis albiventris (Marsupialia: Didelphidae), state of Mato Grosso do Sul, Brazil

Turgida turgida have been largely reported parasitizing Didelphis species in North and South America based on light microscopy observation. However, the features that differentiate T. turgida from other physalopterid species should be observed using scanning electron microscopy (SEM). A female white-bellied opossum, Didelphis albiventris, arrived dead at the Centro de Reabilitação de Animais Silvestres (CRAS) in the municipality of Campo Grande, state of Mato Grosso do Sul, Brazil. During the necropsy, adult nematodes were collected from stomach and intestine. The nematodes were determined to be adult specimens and submitted to SEM for the species determination. This is the first report of T. turgida confirmed by SEM in the Neotropical region and the first report in an urban area in the state of Mato Grosso do Sul, Brazil.

Histochemical study of the oviducal gland and analysis of the sperm storage tubules of Mustelus schmitti Springer, 1939 (Chondrichthyes, Triakidae)

Abstract: The paired oviducal glands of immature and mature females of Mustelus schmitti were examined macro and microscopically. Findings indicate that these glands possessed the same zonation as in most chondrichthyans from anterior to posterior: club, papillary, baffle and terminal zones. The whole gland is composed by simple tubular glands that connect with transverse grooves all along the organ. The club zone presents a typical indian club shape with a simple columnar and ciliated epithelium including secretory cells PAS (+) and AB (+). The papillary zone is characterized by lamella forming small and long cones in numbers of three. The epithelium of this zone contains ciliated cells with apical nuclei and secretory cells with basal nuclei that stain AB (+)The baffle zone consists of apically flattened lamellae alternating with spinnerets which are small projections disposed by both sides of the plateau. This whole structure is present in number of 8 or 9 units. A simple columnar ciliated epithelium covers the plateau and spinnerets and no AB or PAS staining is observed. The epithelium of the terminal zone is PAS (-) and AB (+), and elongated tubules, that run adjacent to the baffle zone are the site where groups of spermatozoa are clearly observed in the lumen. The epithelium of the sperm storage tubules do not stain with any of the dyes tested. Sperm was also observed in the baffle zone, presumably in its way to the fecundation in the oviduct because it displays no aggregation pattern and was between the folds of the epithelium. By scanning electron microscopy sperm was observed in the club and baffle zones in a gland which belonged to a pregnant female.

Critical aspects on the behavior of material from the mechanical tool-workpiece interaction in single point diamond turning

Some material aspects such as grain size, purity and anisotropy exert an important influence on surface quality, especially in single point diamond turning. The aim of this paper is to present and discuss some critical factors that can limit the accuracy of ultraprecision machining of non-ferrous metals and to identify the effects of them on the cutting mechanism with single point diamond tools. This will be carried out through observations of machined surfaces and chips produced using optical and scanning electron microscopy. Solutions to reduce the influence of some of these limiting factors related with the mechanism of generation of mirror-like surfaces will be discussed.

Fracture modes and acoustic emission characteristics of hydrogen-assisted cracking in high-strength low-alloy steel weldment

The aim of the present paper is to study the relationship between the fracture modes in hydrogen-assisted cracking (HAC) in microalloied steel and the emission of acoustic signals during the fracturing process. For this reason, a flux-cored arc weld (FCAW) was used in a high-strength low-alloy steel. The consumable used were the commercially available AWS E120T5-K4 and had a diameter of 1.6 mm. Two different shielding gases were used (CO2 and CO2+5% H2) to obtain complete phenomenon characterization. The implant test was applied with three levels of restriction stresses. An acoustic emission measurement system (AEMS) was coupled to the implant test apparatus. The output signal from the acoustic emission sensor was passed through an electronic amplifier and processed by a root mean square (RMS) voltage converter. Fracture surfaces were examined by scanning electron microscopy (SEM) and image analysis. Fracture modes were related with the intensity, the energy and the number of the peaks of the acoustic emission signal. The shielding gas CO2+5% H2 proved to be very useful in the experiments. Basically, three different fracture modes were identified in terms of fracture appearance: microvoid coalescence (MVC), intergranular (IG) and quasi-cleavage (QC). The results show that each mode of fracture presents a characteristic acoustic signal.

Advanced ceramics: evaluation of the mechanism of stock removal and ground surface quality

The aim of this work is to evaluate the mechanism of stock removal and the ground surface quality of advanced ceramics machined by a surface grinding process using diamond grinding wheels. The analysis of the grinding performance was done regarding the cutting surface wear behavior of the grinding wheel for ceramic workpieces. The ground surface was evaluated using Scanning Electron Microscopy (SEM). As a result it can be said that the mechanism of material removal in the grinding of ceramic is largely one of brittle fracture. The increase of the h max can reduce the tangential force required by the process. Although, it results in an increase in the surface damage, reducing the mechanical properties of the ground component.

Investigation on diamond turning of silicon crystal - generation mechanism of surface cut with worn tool

This paper discusses the effect of tool wear on surface finish in single-point diamond turning of single crystal silicon. The morphology and topography of the machined surface clearly show the type of cutting edge wear reproduced onto the cutting grooves. Scanning electron microscopy is used in order to correlate the cutting edge damage and microtopography features observed through atomic force microscopy. The possible wear mechanisms affecting tool performance and surface generation during cutting are also discussed. The zero degree rake angle single point diamond tool presented small nicks on the cutting edge. The negative rake angle tools presented more a type of crater wear on the rake face. No wear was detected on flank face of the diamond tools.