Adzuki beans (Vigna angularis) seed quality under several drying conditions

This study analyzed the drying process and the seed quality of adzuki beans (Vigna angularis). Grains of adzuki beans, with moisture content of 1.14 (decimal dry basis) at harvest and dried until the moisture content of 0.11 (decimal dry basis.) were used. Drying was done in an experimental drier maintened at controlled temperatures of 30, 40, 50, 60, and 70 ºC and relative humidity of 52.0, 28.0, 19.1, 13.1, and 6.8%, respectively. Physiological and technological seed quality was evaluated using the germination test, Index of Germination Velocity (IGV), electrical conductivity, and water absorption, respectively. Under the conditions tested in the present study, it can be concluded that drying time for adzuki beans decreases with the higher air temperatures of 60 and 70 ºC, and it affected the physiological and technological seed quality. Thus, to avoid compromising adzuki seeds quality, it is recommended to promote its drying up to 50 ºC.

Effect of drying temperature on quality of β-glucan in white oat grains

Oats have received attention because of their nutritional characteristics, especially their high-quality content of β-glucan. The drying process reduces water content; therefore they can be preserved for long periods. However, high-temperature drying process may affect the physical, chemical, and functional properties of the grains. The objective of this study was to evaluate the effect of different drying temperatures on β-glucan quality in oat grains. Grains of oats (Avena sativa, L.), cultivar Albasul, harvested at harvest moisture content of 23% were submitted to stationary drying at air temperatures of 25, 50, 75, and 100 ºC until they reached 13% moisture content. The β-glucan content was determined in samples of oat grains and extraction was performed using water as solvent at 90 ºC. The β-glucan extract was evaluated for water holding capacity, water retention capacity, capacity of displacement, and gelation properties. Stationary of oat grains at air temperatures above 25 ºC decreased the water holding capacity, whereas the content of β-glucan and the water retention capacity of β-glucan extract was affected at temperatures above 50 ºC. Physical changes such as increased gelation capacity of the β-glucan extract occurred following drying at air temperature over 75 ºC.

Estimate of respiration rate and physicochemical changes of fresh-cut apples stored under different temperatures

In this study, the influence of storage temperature and passive modified packaging (PMP) on the respiration rate and physicochemical properties of fresh-cut Gala apples (Malus domestica B.) was investigated. The samples were packed in flexible multilayer bags and stored at 2 °C, 5 °C, and 7 °C for eleven days. Respiration rate as a function of CO2 and O2 concentrations was determined using gas chromatography. The inhibition parameters were estimated using a mathematical model based on Michaelis-Menten equation. The following physicochemical properties were evaluated: total soluble solids, pH, titratable acidity, and reducing sugars. At 2 °C, the maximum respiration rate was observed after 150 hours. At 5 °C and 7 °C the maximum respiration rates were observed after 100 and 50 hours of storage, respectively. The inhibition model results obtained showed a clear effect of CO2 on O2 consumption. The soluble solids decreased, although not significantly, during storage at the three temperatures studied. Reducing sugars and titratable acidity decreased during storage and the pH increased. These results indicate that the respiration rate influenced the physicochemical properties.

Sensory and physico-chemical characteristics of desserts prepared with egg products processed by freeze and spray drying

In this work, three freeze-dried (FD) egg products (whole egg (WE), egg yolk (EY) and egg white (EW)) were obtained and the acceptability of confections prepared with each was evaluated. Sensory analyses for confections were performed by hedonic testing with fifty panelists in each evaluation. The studied confections were: Condensed Milk Pudding (P), Quindim (Q) and Meringue (M). The results obtained for confections made with FD egg products were compared with the achieved through other formulations of the same desserts made with fresh (F) or spray-dried (SD) egg products. The sensory analysis results for confections made with FD egg products showed good acceptance by panelists. A principal component analysis of the sensory evaluation data was carried out to identify similarities between the different egg products. The PCA supported the conclusion that FD egg products can substitute their fresh and SD counterparts in dessert formulations with good acceptability while keeping the advantages conferred by the freeze-drying method.

Characterization of new sources of derivative starches as wall materials of essential oil by spray drying

Starch derivatives of taro (Colocasia esculenta L. Schott) and rice were characterized as wall materials of orange oil (d-limonene) by spray drying. Native starches were initially hydrolyzed with HCl and then esterified. Succinylated starches were modified using a conventional method in a slurry and were extruded; whereas, the phosphorylated starches were modified using the extrusion process. Viscosity and solubility of starches reduced after acid hydrolysis, derivatization, and extrusion. The particle size of the wall materials ranged between 20.05 and 31.81 µm. The encapsulation efficiency of the phosphorylated taro, rice, and waxy corn starches was 96.9, 96.8 and 97.1% respectively, and 98.6, 98.1, and 98.8% for succynilated taro, rice, and waxy corn starches, respectively. Starch derivatives of taro and rice could potentially be used as wall materials of orange oil d-limonene.

Drying kinetics of potato pulp waste

Potato pulp waste (PPW) drying was investigated under different experimental conditions (temperatures from 50 to 70 °C and air flow from 0.06 to 0.092 m³ m- 2 s- 1) as a possible way to recover the waste generated by potato chip industries and to select the best-fit model to the experimental results of PPW drying. As a criterion to evaluate the fitting of mathematical models, a method based on the sum of the scores assigned to the four evaluated statistical parameters was used: regression coefficient (R²), relative mean error P (%), root mean square error (RMSE), and reduced chi-square (χ²). The results revealed that temperature and air velocity are important parameters to reduce PPW drying time. The models Midilli and Diffusion had the lowest sum values, i.e., with the best fit to the drying data, satisfactorily representing the drying kinetics of PPW.

The influence of peeling and type of drying on chemical and sensorial analysis of organic coffee

Organic coffee is characterized by being produced without the use of chemical products and by having a similar or superior quality in comparison to that of coffee produced by traditional methods. The production of organic coffee does not include the use of highly soluble nutrients, which makes consumers concerned with environmental issues and healthy eating habits realize its true value. This paper aims to analyze the influence of harvesting, peeling and drying on the quality of organic coffee, in order to present the best way of producing high quality coffee. Samples of organic coffee were harvested by both conventional and selective ways, and some were peeled. They were then dried on concrete patio and on suspended terraces. The beans were analyzed for potassium leaching, electrical conductivity, titratable acidity, and submitted to coffee cupping-test. The results obtained indicated that the selective harvesting of the peeled or unpeeled cherry coffee dried on concrete terrace is feasible for production of fine coffees. This type of processing effectively influenced the final quality of the organic coffee, thus being an alternative to improve the quality and market value of the product, especially for small producers, cooperatives, and associations of coffee producers.

Convective, vacuum and microwave drying kinetics of mallow leaves and comparison of color and ascorbic acid values of three drying methods

Mallow leaves (Malva sylvestris L.) with initial moisture of 5.02±0.003 on dry basis (82.5% on wet basis) were dried using three different drying methods, microwave, convective and vacuum. The leaves that weigh 75 g each were dried until their moisture fell down to 0.10±0.005 on dry basis (approximately 9% on wet basis). The following drying levels were used in each of the drying processes: 6.67, 8.67, 10, 11.33 W g-1 microwave power density; 50, 75, 100 and 125 °C for convective drying; and 3, 7 kPa at 50 and 75 °C for vacuum drying. Drying periods ranged from 6-10, 26-150 and 38-130 min. for microwave, convective and vacuum drying, respectively. Effective moisture diffisuvities ranged from 2.04403 10-10-3.63996 10-12 m2 s-1, 1.70182 10-11-1.10084 10-10 m2 s-1 and 1.85599 10-11-5.94559 10-10 m2 s-1 for microwave, convective and vacuum drying, respectively. According to ascorbic acid content and color parameters, the best microwave power density was found 10 W g-1 with a drying period of 6.5 min.

Study of the physicochemical characteristics of soursop powder obtained by spray-drying

This study aimed at contributing to the development of new foodstuffs made by soursop pulp powder obtained by spraydrying. Different concentrations of maltodextrin DE 20 (15, 30, and 45%) were added to commercial soursop pulp, which was dehydrated afterwards. The following analyses were carried out: water activity, moisture, pH, soluble solids, acidity, ascorbic acid, hygroscopicity, degree of caking, and rehydration time. The results obtained for the three powder treatments (15, 30 and 45% of maltodextrin) were, respectectively: water activity (0.19a±0.00; 0.20a±0.00; 0.18a±0.01); moisture (1.17c±0.12; 1.47b±0.05; 1.82a±0.06); pH (3.75a±0.05; 3.73a±0.06; 3.70a±0.03); soluble solids (89.67a±0.00; 89.84a±0.00; 90.00a±0.06); acidity (3.01a±0.02; 1.91b±0.03; 1.24c±0.03); ascorbic acid (18.90a±0.00; 14.48b±0.00; 11.26b±0.78); hygroscopicity (5.93a±0.40; 3.82b±0.16; 3.28b±0.38); degree of caking (78.36a±2.86; 35.38b±6.07; 24.77b4.89), and rehydration time (02.03a±0.46; 01.16ab±0.50; 0.59b±0.30). The soursop powders with 30 and 45% of maltodextrin had few significant differences in terms of physicochemical and hygroscopic characteristics, which allow us to consider the percentage of 30% of maltodextrin, in this study, as the best percentage for soursop pulp atomization.

Optimization of microwave drying conditions of two banana varieties using response surface methodology

AbstractOptimization of microwave drying conditions of Luvhele and Mabonde banana varieties were studied using response surface methodology. The drying was performed using a central composite rotatable design for two variables: microwave power level (100, 200 and 300 W) and drying time (40, 26, and 12 min.) for Luvhele; (100, 200 and 300 W) and (42, 27, and 12 min) for Mabonde. The colour and texture (hardness) data were analyzed using ANOVA and regression analysis. The fitness of the models obtained was good as the lack of fit for each of the models was not significant. The coefficient of determination R2 of the models was relatively high, hence the models obtained for the responses were adequate and acceptable. Drying conditions of 178.76 W, 12 min. drying time were found optimum for product quality at a desirability of 0.91 for Luvhele; while 127.67 W, 12 min. with a desirability of 0.86 was predicted for Mabonde. The result of this study could be used as a standard for microwave processing of Luvhele and Mabondebanana varieties.

Influence of the moisture at harvest and drying process of the grains on the level of carotenoids in maize (Zea mays)

AbstractMaize is considered a source of carotenoids; however, these compounds are highly unstable, degraded by high temperatures, exposure to light and presence of oxygen. The objective of this work was to evaluate the influence of the moisture and type of drying applied to grains on the level of carotenoids in yellow maize. The experiment was conducted in a completely randomized design (2 × 4 factorial), two levels of initial moisture at the harvest (22 and 19%) and three types of drying (in the sun; in the shade and in a dryer) and control (no drying). The samples of grains after drying with 12% of final moisture were analyzed by concentration of total carotenoids, carotenes (α-carotene + β-carotene), monohydroxilated carotenoids (β-cryptoxanthin), and xanthophylls (lutein + zeaxanthin). Initial moisture, type of drying and the interaction between moisture versus drying influence (p≤0.05) the levels of carotenoids in grains. This is the first report about the drying conditions and harvest’s initial moisture as influence on the profile and content of carotenoids in maize grains. Based on the results, this work suggested that the harvest be carried out preferably when the grains present 22% humidity, with drying in a dryer or in shade for further use or storage.

Impact of different drying parameters on color, β-carotene, antioxidant activity and minerals of apricot (Prunus armeniacaL.)

Abstract Apricot is one of the fruits dried by using different methods, such as sun, convective or microwave drying. The effects of drying methods on the components of this fruit differ depending upon the temperature or time parameters. In this research, the impacts of convective, microwave and microwave–convective drying techniques on color, β-carotene, minerals and antioxidant activity of apricots were investigated. The color values (L*, b*,ΔEab, h° and C*ab) of dried fruit were decreased, while the a* values increased. Compared with a fresh sample, the dried apricots showed a 1.4-3.9-fold proportional increase in β-carotene based on the increment of dry matter. The samples dried at high temperature and microwave levels, at 75 °C+90 watt and 75 °C+160 watt, showed lower antioxidant activity. Of the different drying treatments, the microwave-convective method (50 °C+160 watt) obtained a higher β-carotene content while maintaining antioxidant activity with a short drying time.

Management of freezing rate and trehalose concentration to improve frozen dough properties and bread quality

Abstract Bread is one of the most consumed foods in the world, and alternatives have been sought to extend its shell life, and freezing is one of the most popular methods. The purpose of this study was to evaluate the effect of freezing rate and trehalose concentration on the fermentative and viscoelastic properties of dough and bread quality. Dough was prepared and trehalose was added at three concentrations (0, 400, 800 ppm); dough was pre fermented and frozen at two freezing rates then stored for 42 days. Frozen dough samples were thawed every two weeks. CO2 production and elastic and viscous modulus were determined. In addition, bread was elaborated and specific volume and firmness were evaluated. High trehalose concentrations (400 and 800 ppm) produced dough with the best viscoelastic and fermentative properties. Greater bread volume and less firmness were observed when a slow freezing rate (-.14 °C/min) was employed.

Drying soybean seed using air ambient temperature at low relative humidity

Under subtropical and tropical environments soybean seed (Glycine max (L.) Merrill) are harvested early to avoid deterioration from weathering. Careful after-harvest drying is required and is an important step in maintaining the physiological quality of the seed. Soybean seed should be harvested when the moisture content is in a range of 16-20%. Traditional drying utilizes a high temperature air stream passed through the seed mass without dehumidification. The drying time is long because the system is inefficient and the high temperature increases the risk of thermal damage to the seed. New technology identified as heat pipe technology (HPT) is available and has the unique feature of removing the moisture from the air stream before it is passed through the seed mass at the same environmental temperature. Two studies were conducted to evaluate the performance of HPT for dry soybean seed. In the first study the seeds were dried from 17.5 to 11.1% in 2 hours and 29 minutes and in the second sudy the seeds were dried from 22.6 to 11.9% in 16 hours and 32 minutes. This drying process caused no reduction in seed quality as measured by the standard germination, tetrazolium-viability, accelerated aging and seedling vigor classification tests. The only parameter that indicated a slight seed quality reduction was tetrazolium vigor in the second study. It was concluded that the HPT system is a promising technology for drying soybean seed when efficiency and maintenance of physiological quality are desired.

Drying and germination of cupuassu (Theobroma grandiflorum (willd. Ex Spreng.) K. Schum.) seeds

The objective of this study was to verify the effect of drying on germination of cupuassu (Theobroma grandiflorum (Willd. ex Spreng) K. Schum.) seeds. Desiccation was in forced air oven, with temperature ranging from 23 to 33ºC. Sowing was carried out at 0.5cm of depth in plastic trays in sand and sawdust mixture (1:1), previously sterilized in hot water (100ºC), during 2h. Seeds were left to germinate in a laboratory with no temperature and relative humidity control, under natural light. It was quantified the seed moisture content, in four replications of 10 seeds; the germination percentage, performed during 30 days, with daily counts of the number of germinated seeds; the germination speed index; and number of days to the germination onset. The experimental design was completely randomized with four replications of 25 seeds. The reduction of moisture content from 58.6 to 37.8% did not affect seed germination and germination speed index; however, they were affected when moisture content was reduced to values below 30.7%. It was observed that only when moisture content was 16.1% seeds demanded more days to begin germination. Cupuassu seeds are classified as recalcitrant and they can be desiccated up to 37.8% with no reduction on germination.