Reforestation feasibility in area formerly used for cattle rasing in the state of Rondônia, Northwest Brazilian Amazon

Little knowledge on initial behavior of native tree species in recovering landscapes in the Amazon is a current concern for expanding reforestation in the region. Thus, the aim of this study was to evaluate the establishment of native tree species that could be used for reforestation in area previously covered by a pasture of brachiaria grass (Brachiaria brizantha) destined for intensive cattle rasing in the State of Rondônia. For this, there were performed previous diagnostic of landscape changes and the election of tree species based on the ecological group information. Some of the critical macronutrients for plant growth were supplied in the holes to alleviate nutrient deficiencies. In addition, growth and survival parameters were taken to evaluate the initial behavior of species. Six native tree species planted with different combinations (10mx10m, 5mx5m and 3mx3m) had survival rate and growth (total height, girth stem and crown projection area) measured in different intervals: 6-month, 12-month and 24-month after planting. All the species presented survival rate over 90% at 24 months and comparable growth indices to other native species under similar situation and in the region. Overall, Schizolobium amazonicum (bandarra), the non-identified legume tree 1 (acácia grande) and Colubrina glandulosa (sóbrasil) averaged over 90% the highest girth stem growth all over the area. S. amazonicum and the non-identified legume tree 1 (acácia grande) presented the best results for height and canopy area growth parameters, respectively. The combination among native tree species from initial successional ecological groups and fertilizer was favorable to promote reforestation in the conditions of the study area in Rondônia.

RESFRIAMENTO ARTIFICIAL EM FORNOS RETANGULARES PARA A PRODUÇÃO DE CARVÃO VEGETAL

RESUMOUm importante aspecto a ser considerado na produção de carvão vegetal é o longo período de resfriamento dos fornos de alvenaria, acarretando na baixa produtividade e exigindo maior número de fornos para suprir a demanda de produção. Pesquisas têm sido desenvolvidas para a redução do tempo de resfriamento dos fornos retangulares, utilizando trocadores de calor. Dessa forma, o objetivo deste trabalho foi avaliar três modelos de trocadores de calor que promovam a redução significativa do tempo de resfriamento. A pesquisa foi realizada na unidade produtora de carvão vegetal Buritis, da Empresa Arcelor Mittal Bioflorestas, localizada na cidade de Martinho Campos, MG. Foram avaliados três diferentes trocadores de calor (Modelos 1, 2 e 3), determinando o tempo, em dias, que os fornos retangulares levavam para atingir a temperatura de 50 ºC em relação ao resfriamento natural. O Modelo 1 apresentou ganho real no tempo de resfriamento de 12,5%; o Modelo 2, ganho real de 38%; e o Modelo 3, com fluxo de gás convencional, apresentou ganho médio de 32%, enquanto no fluxo de gás invertido o ganho foi de 43%. Conclui-se que os trocadores de calor avaliados foram eficientes na redução do tempo de resfriamento dos fornos retangulares para produção de carvão vegetal, elevando, assim, a produtividade dos fornos. O trocador de calor Modelo 3, com fluxo de gás invertido, apresentou o maior ganho real no tempo de resfriamento, além do menor número de focos de incêndio durante o descarregamento do carvão vegetal.

Ambiente térmico no interior de modelos de galpões avícolas em escala reduzida com ventilação natural e artificial dos telhados

O presente trabalho teve o objetivo de avaliar o ambiente térmico no interior de modelos físicos de galpões avícolas construídos em escala reduzida (1:10). O conforto térmico foi avaliado por meio do Índice de Temperatura do Globo Negro e Umidade (ITGU), Carga Térmica de Radiação (CTR) e efetividade das coberturas em reduzir o ITGU em relação à cobertura construída com telhas de alumínio (épsilon). Quatro modelos construídos com telhas cerâmicas e equipados com ventilação natural ou forçada foram comparados a dois modelos construídos com telhas cerâmicas e de alumínio, respectivamente, sem lanternim. Pode-se concluir que as coberturas com câmaras de ventilação artificial (B30CVF) ou natural (B30CVN) proporcionaram melhores ambientes térmicos no interior dos modelos reduzidos, no qual o último tem a vantagem de não requerer gasto de energia elétrica.

Discriminação entre estágios nutricionais na cultura do trigo com técnicas de visão artificial e medidor portátil de clorofila

O ajuste da adubação nitrogenada é um tema que suscita preocupações econômicas e ambientais em todo o mundo. Isso decorre da elevada resposta das culturas, especialmente gramíneas, ao nitrogênio e da falta de métodos adequados de quantificação de sua disponibilidade no solo. Com o objetivo de avaliar a discriminação de três estágios nutricionais na cultura do trigo, foram utilizadas imagens digitais e um medidor portátil de clorofila (SPAD -502). Os dados foram coletados em três épocas (8; 14 e 20 dias após a adubação nitrogenada em cobertura - DAA), em parcelas de trigo submetidas a três doses de N (0; 30 e 60 kg ha-1). As imagens foram processadas para desenvolvimento dos classificadores multivariados, utilizando-se de nove índices espectrais com as combinações dos valores médios dos "pixels". Os dados de clorofila e N foliar foram utilizados para desenvolver classificadores univariados. Verificou-se que o sistema de visão artificial foi mais eficiente que o SPAD aos 8 DAA. Aos 14 e 20 DAA, a classificação univariada com os dados SPAD foi equivalente aos classificadores com dados de imagens. Com a utilização das imagens digitais, foi possível discriminar os estágios nutricionais oito dias após a primeira adubação nitrogenada em cobertura.

Rainfall erosivity for the State of Rio de Janeiro estimated by artificial neural network

The Artificial Neural Networks (ANNs) are mathematical models method capable of estimating non-linear response plans. The advantage of these models is to present different responses of the statistical models. Thus, the objective of this study was to develop and to test ANNs for estimating rainfall erosivity index (EI30) as a function of the geographical location for the state of Rio de Janeiro, Brazil and generating a thematic visualization map. The characteristics of latitude, longitude e altitude using ANNs were acceptable to estimating EI30 and allowing visualization of the space variability of EI30. Thus, ANN is a potential option for the estimate of climatic variables in substitution to the traditional methods of interpolation.

Determination of the influence of the variation of reducing and non-reducing sugars on coffee quality with use of artificial neural network

The present study aimed at evaluating the use of Artificial Neural Network to correlate the values resulting from chemical analyses of samples of coffee with the values of their sensory analyses. The coffee samples used were from the Coffea arabica L., cultivars Acaiá do Cerrado, Topázio, Acaiá 474-19 and Bourbon, collected in the southern region of the state of Minas Gerais. The chemical analyses were carried out for reducing and non-reducing sugars. The quality of the beverage was evaluated by sensory analysis. The Artificial Neural Network method used values from chemical analyses as input variables and values from sensory analysis as output values. The multiple linear regression of sensory analysis values, according to the values from chemical analyses, presented a determination coefficient of 0.3106, while the Artificial Neural Network achieved a level of 80.00% of success in the classification of values from the sensory analysis.

Technical and economic analysis of replacing artificial lighting system to induction of photoperiod effect in begonia's seedlings in greenhouse

The type of artificial light used for inducing photoperiod effect in begonia's seedlings at greenhouse has fundamental importance in the growth and development of these plants and directly reflects in the electrical energy consumption used in this production process. The objective of this research was to analyze the technical and economic feasibility of replacing the current technology of artificial lighting used by the producers (incandescent lamps), by the technology of discharge lamps with the purpose of inducing photoperiod in a greenhouse. The analysis results indicate that the discharge lamp of 32 W Tubular Fluorescent discharge lamp was the one that presented the lower peak demand and lower average energy consumption of 85.01% compared to incandescent filament lamp of 100 W that is the technology of bigger consumption and currently used by the producer.

Technical evaluation of artificial ligthing systems for broiler houses

The spatial distribution of illuminance and the electric consumption of artificial lighting system is one of the main problems related to broiler production. Therefore, the aim of this study was to evaluate the spatial distribution of luminance level and energy efficiency of different lighting systems for broiler houses. Six types of lamps were tested in two different configurations to find the minimum illuminance of 20 and 5 lux. The tested lamps were incandescent (IL) 100 W, compact fluorescent (CFL) 34 W, mixed (ML) 160 W, sodium vapor (SVL) 70 W, T8 fluorescent tube (T8 FTL) 40 W and T5 fluorescent tube (T5 FTL) 28 W. The first four were evaluated with and without reflective light fixture and the latter two without light fixture. It was observed that the tested system with light fixtures negatively affected the spatial distribution of illuminance inside the house. The systems composed by IL and ML without light fixture led to better results in meeting the minimum illuminance of 20 lux and 5 lux, respectively. T5 FTL presented the lowest energy demand.

Low cost driver device for microclimate maintenance in the pre-milking of dairy cattle

Due to the importance of the environment on animal production and thus environmental control, the study aims to build a system for monitoring and control the meteorological variables, temperature and relative humidity, low cost, which can be associated with an evaporative cooling system (ECS). The system development included all the stages of assembly, test and laboratory calibration, and later the validation of the equipment carried in the field. The validation step showed results which allowed concluding that the system can be safely used in the monitoring of these variables. The controller was efficient in management of the microclimate in the waiting corral and allowed the maintenance of the air temperature within the comfort range for dairy cattle in pre-milking with averaged 25.09 ºC during the afternoon. The equipment showed the lower cost (R$ 325.76) when compared to other middle market (R$ 450.00).

Evaluation of the effect of the seed extract of Moringa oleifera Lam over the efficiency of organic filters in wastewater treatment of dairy cattle breeding

This study aimed to evaluate the effect of Moringa oleifera Lam extract on the removal of total solids (TS), total suspended solids (TSS) and chemical oxygen demand (COD), in different filter media for treating wastewater of dairy cattle breeding (DCW). The moringa seed extract was obtained by grinding 50 g of seeds in one liter of distilled water and, after passing the solution through a quantitative paper filter of 25 microns, 60 mL of the extract were added to wastewater from cattle breeding before the filtration process in organic filters made of thin coal, bamboo leaves, eucalyptus leaves, gliricidia branches and sawdust. This was followed by the completely randomized experimental design, adopting a factorial of 5 x 2. Aliquots of filtered effluent were collected and the total solids (TS) concentrations, total suspended solids (TSS) and chemical oxygen demand (COD) were determined. It was found that the increase in the efficiency of removal of COD and total solids can be attributed to the coagulating power of the moringa seed extract, wherein the filter medium with bamboo leaves presented the best performance, showing potential for use as alternative filter material in the primary treatment of DCW.

Performance of an anaerobic-aerobic reactor and kinetic study of organic matter removal of cattle slaughterhouse effluent

This paper sought to evaluate the behavior of an upflow Anaerobic-Aerobic Fixed Bed Reactor (AAFBR) in the treatment of cattle slaughterhouse effluent and determine apparent kinetic constants of the organic matter removal. The AAFBR was operated with no recirculation (Phase I) and with 50% of effluent recirculation (Phase II), with θ of 11h and 8h. In terms of pH, bicarbonate alkalinity and volatile acids, the results indicated the reactor ability to maintain favorable conditions for the biological processes involved in the organic matter removal in both operational phases. The average removal efficiencies of organic matter along the reactor height, expressed in terms of raw COD, were 49% and 68% in Phase I and 54% and 86% in Phase II for θ of 11h and 8h, respectively. The results of the filtered COD indicated removal efficiency of 52% and k = 0.0857h-1 to θ of 11h and 42% and k = 0.0880h-1 to θ of 8h in the Phase I. In Phase II, the removal efficiencies were 59% and 51% to θ of 11h and 8h, with k = 0.1238h-1 and k = 0.1075 h-1, respectively. The first order kinetic model showed good adjustment and described adequately the kinetics of organic matter removal for θ of 11h, with r² equal to 0.9734 and 0.9591 to the Phases I and II, respectively.

Application of response surface methodology to study the biological removal of nitrogen from effluent of cattle slaughterhouse in a sequencing batch reactor

The aim of this study was to evaluate the efficiency of a sequencing batch reactor (SBR) on biological removal of nitrogen from cattle slaughterhouse wastewater by nitrification/denitrification processes. The effects of initial concentration of ammoniacal nitrogen were investigated at 100; 150 and 200 mg L-1 and air flow rate at 0.125; 0.375 and 0.625 L min¹ Lreactor-1 on the nitrogen compounds removal, by a Central Composite Rotational Design (CCRD) configuration. There were variations from 9.2 to 94.9%, 4.0 to 19.6% and 20.8 to 92.0% in the conversion of ammoniacal nitrogen to nitrate and nitrite concentration and removal of total nitrogen, respectively. The increase of air flow rate and decrease of the initial concentration of ammoniacal nitrogen resulted in higher efficiencies of total nitrogen removal, as well as the conversion of ammoniacal nitrogen to nitrate. During the pre-established intervals of this study, the removal and conversion efficiencies of nitrogen compounds above 85% were achieved in air flow rate variations from 0.375 to 0.725 L min-1 Lreactor-1 and initial concentration of ammoniacal nitrogen from 80 to 200 mg L-1. On denitrification process, we obtained efficiencies from 91.5 to 96.9% on the removal of nitrite/nitrate and from 78.3 to 87.9% on the removal of organic matter.

Light emitting diode (LED) use in artificial lighting for broiler chicken production

Light emitting diode (LED) has been used in commercial poultry industry by presenting superior energy savings and providing feasibility on production process. The objective of this research was to evaluate performance and carcass yield of broiler chickens exposed to different LED colors compared with fluorescent lamps. For that, two experiments (E1 and E2) were performed and 2,646 Cobb® chickens were used. In experiment E1, male birds were exposed to 20 lux artificial lighting with red, yellow, blue, and white LED bulbs; and fluorescent bulb. In experiment E2, male and female birds were exposed to 15 lux artificial lighting with red and blue LED bulbs; and fluorescent bulb. Cumulative weight gain (kg), feed intake (kg), feed conversion, hot carcass weight (kg), carcass yield (%), and breast and thigh + drumstick yield (%) were used as response variables. Results showed no difference (p > 0.05) among treatments for performance, carcass yield, and cut yield in experiment E1. In experiment E2 there was only difference between genders (p < 0.05) and males showed higher total weight gain, feed intake, hot carcass weight and thigh + drumstick yield. Different LED color use had same effect as fluorescent lights on broiler performance and carcass yield.

Control of ammonia emissions in naturally ventilated dairy cattle facilities in Portugal

We conducted a study of the processes associated to NH3 emission in naturally ventilated dairy cattle facilities, having described factors that regulate NH3 emission, as well as methodologies for measuring these emissions at these facilities. Appropriate techniques to mitigate NH3 emission in facilities located in regions with warm climates were also identified. The most effective mitigation techniques with simple implementation include strategies associated to: (i) installation design and flooring, which lead to reduced emissions, (ii) excreta pre-excretion, namely the use of diets with optimized crude protein content and increased milk production at farm level; and (iii) excreta post-excretion, particularly by changing the conditions of environmental monitoring within the premises, practice introduction or additive application in the management of excreta deposited on floors.

Corn production for silage intercropped with forage in the farming-cattle breeding integration

Corn cropping for silage, due to the plant material exportation, intercropping with forage provides greater ground cover and straw formation for the Direct Planting System (DPS) continuity. The objective of this study was to evaluate corn production for silage in DPS intercropped with four forages (Urochloa brizantha cv. Marandu, U. ruziziensis cv. Ruziziensis, Panicum maximum cv. Tanzânia and P. maximum cv. Áries). We applied three sowing methods (in row together with corn fertilizer; by no-till sowing simultaneously to corn sowing and at V4 corn stage) and corn without intercropping. The experiment was conducted in autumn/ winter of 2010, in Selvíria - MS, in a randomized block design in factorial arrangement (4 x 3 + 1) and 4 replications. For corn, we evaluated plant height, basal stem diameter, initial and final stand and silage production and for forage dry matter production. Morphological characteristics and corn yield were not affected by intercropping when compared to sole corn crop. Forage dry matter production sown in corn row with fertilizer is a highlight, which in addition to providing greater productivity, harnesses the operation during sowing.