The nitrate to ammonia and ceramic (NAC) process for the denitration and immobilization of low-level radioactive liquid waste (LLW)

Hazardous radioactive liquid waste is the legacy of more than 50 years of plutonium production associated with the United States' nuclear weapons program. It is estimated that more than 245,000 tons of nitrate wastes are stored at facilities such as the single-shell tanks (SST) at the Hanford Site in the state of Washington, and the Melton Valley storage tanks at Oak Ridge National Laboratory (ORNL) in Tennessee. In order to develop an innovative, new technology for the destruction and immobilization of nitrate-based radioactive liquid waste, the United State Department of Energy (DOE) initiated the research project which resulted in the technology known as the Nitrate to Ammonia and Ceramic (NAC) process. However, inasmuch as the nitrate anion is highly mobile and difficult to immobilize, especially in relatively porous cement-based grout which has been used to date as a method for the immobilization of liquid waste, it presents a major obstacle to environmental clean-up initiatives. Thus, in an effort to contribute to the existing body of knowledge and enhance the efficacy of the NAC process, this research involved the experimental measurement of the rheological and heat transfer behaviors of the NAC product slurry and the determination of the optimal operating parameters for the continuous NAC chemical reaction process. Test results indicate that the NAC product slurry exhibits a typical non-Newtonian flow behavior. Correlation equations for the slurry's rheological properties and heat transfer rate in a pipe flow have been developed; these should prove valuable in the design of a full-scale NAC processing plant. The 20-percent slurry exhibited a typical dilatant (shear thickening) behavior and was in the turbulent flow regime due to its lower viscosity. The 40-percent slurry exhibited a typical pseudoplastic (shear thinning) behavior and remained in the laminar flow regime throughout its experimental range. The reactions were found to be more efficient in the lower temperature range investigated. With respect to leachability, the experimental final NAC ceramic waste form is comparable to the final product of vitrification, the technology chosen by DOE to treat these wastes. As the NAC process has the potential of reducing the volume of nitrate-based radioactive liquid waste by as much as 70 percent, it not only promises to enhance environmental remediation efforts but also effect substantial cost savings. ^

Consumer (dis)satisfaction response to disconfirmation: An examination of the form and the underlying process

The purpose of this dissertation was to examine the form of the consumer satisfaction/dissatisfaction (CS/D) response to disconfirmation. In addition, the cognitive and affective processes underlying the response were also explored. ^ Respondents were provided with information from a prior market research study about a new brand of printer that was being tested. This market research information helped set prior expectations regarding the print quality. Subjects were randomly assigned to an experimental condition that manipulated prior expectations to be either positive or negative. Respondents were then provided with printouts that had performance quality that was either worse (negative disconfirmation) or better (positive disconfirmation) than the prior expectations. In other words, for each level of expectation, respondents were assigned to either positive or negative disconfirmation condition. Subjects were also randomly assigned to a condition of either a high or low level of outcome involvement. ^ Analyses of variance indicated that positive disconfirmation led to a more intense CS/D response than negative disconfirmation, even though there was no significant difference in the intensity for positive and negative disconfirmation. Intensity of CS/D was measured by the distance of the CS/D rating from the midpoint of the scale. The study also found that although outcome involvement did not influence the polarity of the CS/D response, the more direct measures of processing involvement such as the subjects' concentration, attention and care in evaluating the printout did have a significant positive effect on CS/D intensity. ^ Analyses of covariance also indicated that the relationship between the intensity of the CS/D response and the intensity of the disconfirmation was mediated by the intensity of affective responses. Positive disconfirmation led to more intense affective responses than negative disconfirmation. ^

Development, validation and uncertainty analysis of quantitative structure and activity relationship models for Log P of disinfection by -products

Hydrophobicity as measured by Log P is an important molecular property related to toxicity and carcinogenicity. With increasing public health concerns for the effects of Disinfection By-Products (DBPs), there are considerable benefits in developing Quantitative Structure and Activity Relationship (QSAR) models capable of accurately predicting Log P. In this research, Log P values of 173 DBP compounds in 6 functional classes were used to develop QSAR models, by applying 3 molecular descriptors, namely, Energy of the Lowest Unoccupied Molecular Orbital (ELUMO), Number of Chlorine (NCl) and Number of Carbon (NC) by Multiple Linear Regression (MLR) analysis. The QSAR models developed were validated based on the Organization for Economic Co-operation and Development (OECD) principles. The model Applicability Domain (AD) and mechanistic interpretation were explored. Considering the very complex nature of DBPs, the established QSAR models performed very well with respect to goodness-of-fit, robustness and predictability. The predicted values of Log P of DBPs by the QSAR models were found to be significant with a correlation coefficient R2 from 81% to 98%. The Leverage Approach by Williams Plot was applied to detect and remove outliers, consequently increasing R 2 by approximately 2% to 13% for different DBP classes. The developed QSAR models were statistically validated for their predictive power by the Leave-One-Out (LOO) and Leave-Many-Out (LMO) cross validation methods. Finally, Monte Carlo simulation was used to assess the variations and inherent uncertainties in the QSAR models of Log P and determine the most influential parameters in connection with Log P prediction. The developed QSAR models in this dissertation will have a broad applicability domain because the research data set covered six out of eight common DBP classes, including halogenated alkane, halogenated alkene, halogenated aromatic, halogenated aldehyde, halogenated ketone, and halogenated carboxylic acid, which have been brought to the attention of regulatory agencies in recent years. Furthermore, the QSAR models are suitable to be used for prediction of similar DBP compounds within the same applicability domain. The selection and integration of various methodologies developed in this research may also benefit future research in similar fields.

Comprehensive process maps for synthesizing high density aluminum oxide-carbon nanotube coatings by plasma spraying for improved mechanical and wear properties

Plasma sprayed aluminum oxide ceramic coating is widely used due to its outstanding wear, corrosion, and thermal shock resistance. But porosity is the integral feature in the plasma sprayed coating which exponentially degrades its properties. In this study, process maps were developed to obtain Al2O3-CNT composite coatings with the highest density (i.e. lowest porosity) and improved mechanical and wear properties. Process map is defined as a set of relationships that correlates large number of plasma processing parameters to the coating properties. Carbon nanotubes (CNTs) were added as reinforcement to Al2O 3 coating to improve the fracture toughness and wear resistance. Two novel powder processing approaches viz spray drying and chemical vapor growth were adopted to disperse CNTs in Al2O3 powder. The degree of CNT dispersion via chemical vapor deposition (CVD) was superior to spray drying but CVD could not synthesize powder in large amount. Hence optimization of plasma processing parameters and process map development was limited to spray dried Al2O3 powder containing 0, 4 and 8 wt. % CNTs. An empirical model using Pareto diagram was developed to link plasma processing parameters with the porosity of coating. Splat morphology as a function of plasma processing parameter was also studied to understand its effect on mechanical properties. Addition of a mere 1.5 wt. % CNTs via CVD technique showed ∼27% and ∼24% increase in the elastic modulus and fracture toughness respectively. Improved toughness was attributed to combined effect of lower porosity and uniform dispersion of CNTs which promoted the toughening by CNT bridging, crack deflection and strong CNT/Al2O3 interface. Al2O 3-8 wt. % CNT coating synthesized using spray dried powder showed 73% improvement in the fracture toughness when porosity reduced from 4.7% to 3.0%. Wear resistance of all coatings at room and elevated temperatures (573 K, 873 K) showed improvement with CNT addition and decreased porosity. Such behavior was due to improved mechanical properties, protective film formation due to tribochemical reaction, and CNT bridging between the splats. Finally, process maps correlating porosity content, CNT content, mechanical properties, and wear properties were developed.

The use of treatment process variables to differentiate between completers and dropouts for a guided self -change adolescent substance abuse intervention

This study documented differences between substance using adolescent participants who either completed or dropped out of a brief motivational intervention. Therapeutic alliance, working alliance and patient involvement were used to describe differences in treatment process ratings in a sample of majority Latino males who either (a) completed a adolescent substance abuse intervention called Alcohol Treatment Targeting Adolescents In Need (ATTAIN) or (b) dropped out after the first or second Guided Self-Change therapy session. Fifteen-minute segments were copied from the midpoint of previously recorded audio-tapes of Guided Self-Change therapy sessions. Raters were trained to a criterion level of interrater reliability for both the Working Alliance Inventory-Short and Vanderbilt Psychotherapy Process Scale. Correlations among Working Alliance Inventory- Short and Vanderbilt Psychotherapy Process Scale subscales reflected a general similarity in the assignment of ratings to client-therapist dyads. Findings underscore why these concepts are often used interchangeably in the treatment process literature. The Vanderbilt Psychotherapy Process Scale patient participation subscale demonstrated substantial empirical differentiation from overall therapeutic alliance. Discriminant function analysis demonstrated the Working Alliance Inventory-Short goal subscale and the Vanderbilt Psychotherapy Process Scale patient participation and therapist warmth and friendliness subscales as successful classifiers of groups of mostly Latino youth based on completion status. Follow-up logistic regression analyses confirmed major findings and successfully predicted group membership. Treatment process constructs can be used as clinical tools to identify participants who may be susceptible to dropping out of treatment services. Further investigation of treatment process may enhance understanding of the influence of alliance between clients and Guided Self-Change therapists. Investigating the role of treatment process as a critical component of brief motivational interventions for substance-using adolescents will inform both practitioners and researchers regarding the effectiveness of community-based substance abuse interventions for adolescents.