A heuristic algorithm to generate test program sequences for moving probe electronic test equipment

The electronics industry, is experiencing two trends one of which is the drive towards miniaturization of electronic products. The in-circuit testing predominantly used for continuity testing of printed circuit boards (PCB) can no longer meet the demands of smaller size circuits. This has lead to the development of moving probe testing equipment. Moving Probe Test opens up the opportunity to test PCBs where the test points are on a small pitch (distance between points). However, since the test uses probes that move sequentially to perform the test, the total test time is much greater than traditional in-circuit test. While significant effort has concentrated on the equipment design and development, little work has examined algorithms for efficient test sequencing. The test sequence has the greatest impact on total test time, which will determine the production cycle time of the product. Minimizing total test time is a NP-hard problem similar to the traveling salesman problem, except with two traveling salesmen that must coordinate their movements. The main goal of this thesis was to develop a heuristic algorithm to minimize the Flying Probe test time and evaluate the algorithm against a "Nearest Neighbor" algorithm. The algorithm was implemented with Visual Basic and MS Access database. The algorithm was evaluated with actual PCB test data taken from Industry. A statistical analysis with 95% C.C. was performed to test the hypothesis that the proposed algorithm finds a sequence which has a total test time less than the total test time found by the "Nearest Neighbor" approach. Findings demonstrated that the proposed heuristic algorithm reduces the total test time of the test and, therefore, production cycle time can be reduced through proper sequencing.

Development of surface flaw thresholds for pre-cured fiber reinforced polymer and groove size tolerance for near surface mounted fiber reinforced polymer retrofit systems

Since the introduction of fiber reinforced polymers (FRP) for the repair and retrofit of concrete structures in the 1980’s, considerable research has been devoted to the feasibility of their application and predictive modeling of their performance. However, the effects of flaws present in the constitutive components and the practices in substrate preparation and treatment have not yet been thoroughly studied. This research aims at investigating the effect of surface preparation and treatment for the pre-cured FRP systems and the groove size tolerance for near surface mounted (NSM) FRP systems; and to set thresholds for guaranteed system performance. This study was conducted as part of the National Cooperative Highway Research Program (NCHRP) Project 10-59B to develop construction specifications and process control manual for repair and retrofit of concrete structures using bonded FRP systems. The research included both analytical and experimental components. The experimental program for the pre-cured FRP systems consisted of a total of twenty-four (24) reinforced concrete (RC) T-beams with various surface preparation parameters and surface flaws, including roughness, flatness, voids and cracks (cuts). For the NSM FRP systems, a total of twelve (12) additional RC T-beams were tested with different grooves sizes for FRP bars and strips. The analytical program included developing an elaborate nonlinear finite element model using the general purpose software ANSYS. The bond interface between FRP and concrete was modeled by a series of nonlinear springs. The model was validated against test data from the present study as well as those available from the literature. The model was subsequently used to extend the experimental range of parameters for surface flatness in pre-cured FRP systems and for groove size study in the NSM FRP systems. Test results, confirmed by further analyses, indicated that contrary to the general belief in the industry, the impact of surface roughness on the global performance of pre-cured FRP systems was negligible. The study also verified that threshold limits set for wet lay-up FRP systems can be extended to pre-cured systems. The study showed that larger surface voids and cracks (cuts) can adversely impact both the strength and ductility of pre-cured FRP systems. On the other hand, frequency (or spacing) of surface cracks (cuts) may only affect system ductility rather than its strength. Finally, within the range studied, groove size tolerance of ±1/8 in. does not appear to have an adverse effect on the performance of NSM FRP systems.

Reliability analysis of encapsulation methods for lead -based paint through an accelerated life testing

The adverse health effects of long-term exposure to lead are well established, with major uptake into the human body occurring mainly through oral ingestion by young children. Lead-based paint was frequently used in homes built before 1978, particularly in inner-city areas. Minority populations experience the effects of lead poisoning disproportionately. ^ Lead-based paint abatement is costly. In the United States, residents of about 400,000 homes, occupied by 900,000 young children, lack the means to correct lead-based paint hazards. The magnitude of this problem demands research on affordable methods of hazard control. One method is encapsulation, defined as any covering or coating that acts as a permanent barrier between the lead-based paint surface and the environment. ^ Two encapsulants were tested for reliability and effective life span through an accelerated lifetime experiment that applied stresses exceeding those encountered under normal use conditions. The resulting time-to-failure data were used to extrapolate the failure time under conditions of normal use. Statistical analysis and models of the test data allow forecasting of long-term reliability relative to the 20-year encapsulation requirement. Typical housing material specimens simulating walls and doors coated with lead-based paint were overstressed before encapsulation. A second, un-aged set was also tested. Specimens were monitored after the stress test with a surface chemical testing pad to identify the presence of lead breaking through the encapsulant. ^ Graphical analysis proposed by Shapiro and Meeker and the general log-linear model developed by Cox were used to obtain results. Findings for the 80% reliability time to failure varied, with close to 21 years of life under normal use conditions for encapsulant A. The application of product A on the aged gypsum and aged wood substrates yielded slightly lower times. Encapsulant B had an 80% reliable life of 19.78 years. ^ This study reveals that encapsulation technologies can offer safe and effective control of lead-based paint hazards and may be less expensive than other options. The U.S. Department of Health and Human Services and the CDC are committed to eliminating childhood lead poisoning by 2010. This ambitious target is feasible, provided there is an efficient application of innovative technology, a goal to which this study aims to contribute. ^

The effects of student -centered and traditional models of teaching on reading skills

A pre-test, post-test, quasi-experimental design was used to examine the effects of student-centered and traditional models of reading instruction on outcomes of literal comprehension and critical thinking skills. The sample for this study consisted of 101 adult students enrolled in a high-level developmental reading course at a large, urban community college in the Southeastern United States. The experimental group consisted of 48 students, and the control group consisted of 53 students. Students in the experimental group were limited in the time spent reading a course text of basic skills, with instructors using supplemental materials such as poems, news articles, and novels. Discussions, the reading-writing connection, and student choice in material selection were also part of the student-centered curriculum. Students in the control group relied heavily on a course text and vocabulary text for reading material, with great focus placed on basic skills. Activities consisted primarily of multiple-choice questioning and quizzes. The instrument used to collect pre-test data was Descriptive Tests of Language Skills in Reading Comprehension; post-test data were taken from the Florida College Basic Skills Exit Test. A MANCOVA was used as the statistical method to determine if either model of instruction led to significantly higher gains in literal comprehension skills or critical thinking skills. A paired samples t-test was also used to compare pre-test and post-test means. The results of the MANCOVA indicated no significant difference between instructional models on scores of literal comprehension and critical thinking. Neither was there any significant difference in scores between subgroups of age (under 25 and 25 and older) and language background (native English speaker and second-language learner). The results of the t-test indicated, however, that students taught under both instructional models made significant gains in on both literal comprehension and critical thinking skills from pre-test to post-test.

Flexible pavement layer moduli determination : an adaptive artificial neural network approach

The estimation of pavement layer moduli through the use of an artificial neural network is a new concept which provides a less strenuous strategy for backcalculation procedures. Artificial Neural Networks are biologically inspired models of the human nervous system. They are specifically designed to carry out a mapping characteristic. This study demonstrates how an artificial neural network uses non-destructive pavement test data in determining flexible pavement layer moduli. The input parameters include plate loadings, corresponding sensor deflections, temperature of pavement surface, pavement layer thicknesses and independently deduced pavement layer moduli.

Initial placement methods for Haitian adult ESOL students : the NYS place test plus profile data compared to subjective assessment

Few valid and reliable placement procedures are available to assess the English language proficiency of adults who enroll in English for Speakers of Other Languages (ESOL) programs. Whereas placement material exists for children and university ESOL students, the needs of students in adult community education programs have not been adequately addressed. Furthermore, the research suggests that a number of variables, such as, native language, age, prior schooling, length of residence, and employment are related to second language acquisition. Numerous studies contribute to our understanding of the relationship of these factors to second language acquisition of Spanish-speaking students. Again, there is a void in the research investigating the factors affecting second language acquisition and consequently, appropriate placement of Haitian Creole-speaking students. This study compared a standardized instrument, the NYS Place Test, used alone and in combination with a writing sample in English, to subjective judgement of a department coordinator for initial placement of Haitian adult ESOL students in a community education program. The study also investigated whether or not consideration of student profile data improved the accuracy of the test. Finally, the study sought to determine if a relationship existed between student profile data and those who withdrew from the program or did not enter a class after registering. Analysis of the data by crosstabulation and chi-square revealed that the standardized NYS Place Test was at least as accurate as subjective department coordinator placement and that one procedure could be substituted for li other. Although the writing sample in English improved accuracy of placement by the NYS test, the results were not significant. Of the profile variables, only length of residence was found to be significantly related to accuracy of placement using the NYS Place Test. The number of incorrect placements was higher for those students who lived in the host country from twenty-five to one hundred ten months. A post hoc analysis of NYS test scores according to level showed that those learners who placed in level three also had a significantly higher incidence of incorrect placements. No significant relationship was observed between the profile variables and those who withdrew from the program or registered but did not enter a class.