Design, fabrication, and evaluation of on-chip micro-supercapacitors

Due to the increasing demand for high power and reliable miniaturized energy storage devices, the development of micro-supercapacitors or electrochemical micro-capacitors have attracted much attention in recent years. This dissertation investigates several strategies to develop on-chip micro-supercapacitors with high power and energy density. Micro-supercapacitors based on interdigitated carbon micro-electrode arrays are fabricated through carbon microelectromechanical systems (C-MEMS) technique which is based on carbonization of patterned photoresist. To improve the capacitive behavior, electrochemical activation is performed on carbon micro-electrode arrays. The developed micro-supercapacitors show specific capacitances as high as 75 mFcm-2 at a scan rate of 5 mVs -1 after electrochemical activation for 30 minutes. The capacitance loss is less than 13% after 1000 cyclic voltammetry (CV) cycles. These results indicate that electrochemically activated C-MEMS micro-electrode arrays are promising candidates for on-chip electrochemical micro-capacitor applications. The energy density of micro-supercapacitors was further improved by conformal coating of polypyrrole (PPy) on C-MEMS structures. In these types of micro-devices the three dimensional (3D) carbon microstructures serve as current collectors for high energy density PPy electrodes. The electrochemical characterizations of these micro-supercapacitors show that they can deliver a specific capacitance of about 162.07 mFcm-2 and a specific power of 1.62mWcm -2 at a 20 mVs-1 scan rate. Addressing the need for high power micro-supercapacitors, the application of graphene as electrode materials for micro-supercapacitor was also investigated. The present study suggests a novel method to fabricate graphene-based micro-supercapacitors with thin film or in-plane interdigital electrodes. The fabricated micro-supercapacitors show exceptional frequency response and power handling performance and could effectively charge and discharge at rates as high as 50 Vs-1. CV measurements show that the specific capacitance of the micro-supercapacitor based on reduced graphene oxide and carbon nanotube composites is 6.1 mFcm -2 at scan rate of 0.01Vs-1. At a very high scan rate of 50 Vs-1, a specific capacitance of 2.8 mFcm-2 (stack capacitance of 3.1 Fcm-3) is recorded. This unprecedented performance can potentially broaden the future applications of micro-supercapacitors.

Assessment of policies for innovative financing in infrastructure systems

Infrastructure systems are drivers of the economy in the nation. A dollar spent on infrastructure development yields roughly double the initial spending in ultimate economic output in the short term; and over a twenty-year period, and generalized ‘public investment’ produces an aggregated $3.21 of economic activity per $1.00 spent [1]. Thus, formulation of policies pertaining to infrastructure investment and development is of significance affecting the social and economic wellbeing of the nation. The aim of this policy brief is to evaluate innovative financing in infrastructure systems from two different perspectives: (1) through consideration of the current condition of infrastructure in the U.S., the current trends in public spending, and the emerging innovative financing tools; (2) through evaluation of the roles and interactions of different agencies in the creation and the diffusion of innovative financing tools. Then using the example of transportation financing, the policy brief provides an assessment of policy landscapes which could lead to the closure of infrastructure financing gap in the U.S and proposes strategies for citizen involvement to gain public support of innovative financing.

Looking At Residents’ Attitudes towards Spring Break Tourism in Texas through the Lens of Community Attachment

The growth of spring break tourism in many destinations has become problematic, predominantly due to the excessive behaviour of college students. This paper examines residents’ attitudes toward spring break tourism in South Padre Island (located in Texas, USA) through the lens of community attachment. By understanding the attitudes of residents of the host communities, tourism planners and policy-makers can create policies to shape the character of tourism according to the residents’ needs. The findings suggest that, at this point in time, community residents perceive that the benefits of spring break tourism benefits exceed its’ costs. Also, the short and intense season of spring break tourism allows residents to better deal with social costs.

Design and evaluation of a consulting system for database design

Database design is a difficult problem for non-expert designers. It is desirable to assist such designers during the problem solving process by means of a knowledge based (KB) system. Although a number of prototype KB systems have been proposed, there are many shortcomings. Firstly, few have incorporated sufficient expertise in modeling relationships, particularly higher order relationships. Secondly, there does not seem to be any published empirical study that experimentally tested the effectiveness of any of these KB tools. Thirdly, problem solving behavior of non-experts, whom the systems were intended to assist, has not been one of the bases for system design. In this project, a consulting system, called CODA, for conceptual database design that addresses the above short comings was developed and empirically validated. More specifically, the CODA system incorporates (a) findings on why non-experts commit errors and (b) heuristics for modeling relationships. Two approaches to knowledge base implementation were used and compared in this project, namely system restrictiveness and decisional guidance (Silver 1990). The Restrictive system uses a proscriptive approach and limits the designer's choices at various design phases by forcing him/her to follow a specific design path. The Guidance system approach, which is less restrictive, involves providing context specific, informative and suggestive guidance throughout the design process. Both the approaches would prevent erroneous design decisions. The main objectives of the study are to evaluate (1) whether the knowledge-based system is more effective than the system without a knowledge-base and (2) which approach to knowledge implementation - whether Restrictive or Guidance - is more effective. To evaluate the effectiveness of the knowledge base itself, the systems were compared with a system that does not incorporate the expertise (Control). An experimental procedure using student subjects was used to test the effectiveness of the systems. The subjects solved a task without using the system (pre-treatment task) and another task using one of the three systems, viz. Control, Guidance or Restrictive (experimental task). Analysis of experimental task scores of those subjects who performed satisfactorily in the pre-treatment task revealed that the knowledge based approach to database design support lead to more accurate solutions than the control system. Among the two KB approaches, Guidance approach was found to lead to better performance when compared to the Control system. It was found that the subjects perceived the Restrictive system easier to use than the Guidance system.

Design and evaluation of a consulting system for database design

Database design is a difficult problem for non-expert designers. It is desirable to assist such designers during the problem solving process by means of a knowledge based (KB) system. A number of prototype KB systems have been proposed, however there are many shortcomings. Few have incorporated sufficient expertise in modeling relationships, particularly higher order relationships. There has been no empirical study that experimentally tested the effectiveness of any of these KB tools. Problem solving behavior of non-experts, whom the systems were intended to assist, has not been one of the bases for system design. In this project a consulting system for conceptual database design that addresses the above short comings was developed and empirically validated.^ The system incorporates (a) findings on why non-experts commit errors and (b) heuristics for modeling relationships. Two approaches to knowledge base implementation--system restrictiveness and decisional guidance--were used and compared in this project. The Restrictive approach is proscriptive and limits the designer's choices at various design phases by forcing him/her to follow a specific design path. The Guidance system approach which is less restrictive, provides context specific, informative and suggestive guidance throughout the design process. The main objectives of the study are to evaluate (1) whether the knowledge-based system is more effective than a system without the knowledge-base and (2) which knowledge implementation--restrictive or guidance--strategy is more effective. To evaluate the effectiveness of the knowledge base itself, the two systems were compared with a system that does not incorporate the expertise (Control).^ The experimental procedure involved the student subjects solving a task without using the system (pre-treatment task) and another task using one of the three systems (experimental task). The experimental task scores of those subjects who performed satisfactorily in the pre-treatment task were analyzed. Results are (1) The knowledge based approach to database design support lead to more accurate solutions than the control system; (2) No significant difference between the two KB approaches; (3) Guidance approach led to best performance; and (4) The subjects perceived the Restrictive system easier to use than the Guidance system. ^

Menu Analysis: Review and Evaluation

In the article - Menu Analysis: Review and Evaluation - by Lendal H. Kotschevar, Distinguished Professor School of Hospitality Management, Florida International University, Kotschevar’s initial statement reads: “Various methods are used to evaluate menus. Some have quite different approaches and give different information. Even those using quite similar methods vary in the information they give. The author attempts to describe the most frequently used methods and to indicate their value. A correlation calculation is made to see how well certain of these methods agree in the information they give.” There is more than one way to look at the word menu. The culinary selections decided upon by the head chef or owner of a restaurant, which ultimately define the type of restaurant is one way. The physical outline of the food, which a patron actually holds in his or her hand, is another. These descriptions are most common to the word, menu. The author primarily concentrates on the latter description, and uses the act of counting the number of items sold on a menu to measure the popularity of any particular item. This, along with a formula, allows Kotschevar to arrive at a specific value per item. Menu analysis would appear a difficult subject to broach. How does a person approach a menu analysis, how do you qualify and quantify a menu; it seems such a subjective exercise. The author offers methods and outlines on approaching menu analysis from empirical perspectives. “Menus are often examined visually through the evaluation of various factors. It is a subjective method but has the advantage of allowing scrutiny of a wide range of factors which other methods do not,” says Distinguished Professor, Kotschevar. “The method is also highly flexible. Factors can be given a score value and scores summed to give a total for a menu. This allows comparison between menus. If the one making the evaluations knows menu values, it is a good method of judgment,” he further offers. The author wants you to know that assigning values is fundamental to a pragmatic menu analysis; it is how the reviewer keeps score, so to speak. Value merit provides reliable criteria from which to gauge a particular menu item. In the final analysis, menu evaluation provides the mechanism for either keeping or rejecting selected items on a menu. Kotschevar provides at least three different matrix evaluation methods; they are defined as the Miller method, the Smith and Kasavana method, and the Pavesic method. He offers illustrated examples of each via a table format. These are helpful tools since trying to explain the theories behind the tables would be difficult at best. Kotschevar also references examples of analysis methods which aren’t matrix based. The Hayes and Huffman - Goal Value Analysis - is one such method. The author sees no one method better than another, and suggests that combining two or more of the methods to be a benefit.

Hispanic -serving land -grant colleges: Analysis and plan for an educational policy initiative

Hispanics and other minority Americans are denied access to higher education by a system that needs structural reform. The purpose of the research was to determine whether creating Hispanic-serving land-grant colleges, similar to the Morrill land-grant colleges serving Black and Native Americans, might be an effective strategy to increase the access of Hispanic students to quality higher education. In addition to published materials, data was collected from a survey of Hispanic-serving institutions and extensive interviews with college presidents, government representatives, educational association leaders, and educational historians. ^ The research examined how existing land-grant college systems came into being and how they have evolved. A look at the functions of the land-grant systems serving Blacks and Native Americans revealed promising possibilities for a system that would include more Hispanics. Legal, fiscal, curricular, and organizational criteria were inferred from the existing systems. While none of the existing land-grant systems can be adapted to serve Hispanics or most other minorities outside their limited regions, each has elements that could be adapted by a new minority-serving system. A number of colleges already have features that could make them candidates for state designation as land-grant colleges. ^ The research suggests that a new federally funded system of Morrill land-grant colleges dedicated to serving all urban Americans, not just Hispanics, would do much to increase the numbers of Hispanic students and other racially and ethnically minority Americans in good quality higher educational institutions. An inclusive urban land-grant system would be politically feasible, whereas one meant to serve Hispanics alone would not. Because of their urban locations, these universities would serve large concentrations of minority citizens of all ethnic groups. ^ Finally, the basic elements of a strategic plan are presented for an educational organization to use for organizing leaders of minority educational associations, financing an initiative to lobby Congress, eliciting legislative and federal agency support, and securing the assistance of other educational, industrial, and special interest groups. The plan includes a suggested timetable for action. Recommendations are made for innovations that would make such a higher education system distinctive and would help meet important national needs. ^

Analysis and design of tall concrete buildings : an investigation regarding the use of cracked versus un-cracked moment of inertia

A debate is currently prevalent among the structural engineers regarding the use of cracked versus un-cracked moment of inertia of the structural elements in analyzing and designing tall concrete buildings. (The basic definition of a tall building, according to the Journal of Structural Design of Tall Buildings Vol. 13. No. 5, 2004 is a structure that is equal to or greater than 160 feet in height, or 6 stories or greater.) The controversy is the result of differing interpretations of certain ACI (American Concrete Institute) code provisions. The issue is whether designers should use cracked moment of inertia in order to estimate lateral deflection and whether the computed lateral deflection should be used to carry out subsequent second-order analysis (analysis considering the effect of first order lateral deflections on bending moment and shear stresses). On one hand, bending moments and shear forces estimated based on un-cracked moment of inertia of the sections may result in conservative designs by overestimating moments and shears. On the other hand, lateral deflections may be underestimated due to the same analyses resulting in unsafe designs.

Planning and evaluation of Business English course in compliance with internationalization in Taiwan: A case study of Tainan Women's College of Arts & Technology

In compliance with the economic internationalization movement and the development of Asia-Pacific Regional Operation Center (APROC) in Taiwan, international business has become more and more important. To sustain favorable trade balances every year and the promotion of APROC in Taiwan, more and more talent with knowledge and skills of Business English are needed. As a consequence, it is necessary to make Business English curriculum appropriate to meet the emerging needs.^ Two groups, experimental and control, received the revised or traditional Business English course to answer the question, "Does the Business English curriculum at Tainan Woman's College of Arts & Technology (TWCAT) meet the needs of students?" Ninety-five subjects were randomly selected from the commercial departments at TWCAT and then randomly assigned to the two groups. In addition, the Business English scores of the subjects' previous semester were collected and analyzed to justify the random selection and assignment. The finding was that their initial equivalence was proved.^ A questionnaire for students and another one for the business community were administered to facilitate data collection and analysis. The results of the questionnaires were used to modify the curriculum content of Business English.^ A final-term examination was given to the subjects at the end of the pilot study of Business English in early May of 1998. The resulting scores of the examination were used to determine if there was a significant difference in learning achievement between the students of the two groups.^ Using Independent Samples Test, significant results indicated that the experimental group had higher level of learning Business English than the control group. The finding supports the hypothesis of this study.^ Recommendations based on these results are that the revised curriculum be adapted and used by TWCAT because it better meets student needs. ^

High frequency electric machine models for the evaluation of operational impacts in integrated drives

A high frequency physical phase variable electric machine model was developed using FE analysis. The model was implemented in a machine drive environment with hardware-in-the-loop. The novelty of the proposed model is that it is derived based on the actual geometrical and other physical information of the motor, considering each individual turn in the winding. This is the first attempt to develop such a model to obtain high frequency machine parameters without resorting to expensive experimental procedures currently in use. The model was used in a dynamic simulation environment to predict inverter-motor interaction. This includes motor terminal overvoltage, current spikes, as well as switching effects. In addition, a complete drive model was developed for electromagnetic interference (EMI) analysis and evaluation. This consists of the lumped parameter models of different system components, such as cable, inverter, and motor. The lumped parameter models enable faster simulations. The results obtained were verified by experimental measurements and excellent agreements were obtained. A change in the winding arrangement and its influence on the motor high frequency behavior has also been investigated. This was shown to have a little effect on the parameter values and in the motor high frequency behavior for equal number of turns. An accurate prediction of overvoltage and EMI in the design stages of the drive system would reduce the time required for the design modifications as well as for the evaluation of EMC compliance issues. The model can be utilized in the design optimization and insulation selection for motors. Use of this procedure could prove economical, as it would help designers develop and test new motor designs for the evaluation of operational impacts in various motor drive applications.

Business process quantitative analysis and optimization for service industries

The total time a customer spends in the business process system, called the customer cycle-time, is a major contributor to overall customer satisfaction. Business process analysts and designers are frequently asked to design process solutions with optimal performance. Simulation models have been very popular to quantitatively evaluate the business processes; however, simulation is time-consuming and it also requires extensive modeling experiences to develop simulation models. Moreover, simulation models neither provide recommendations nor yield optimal solutions for business process design. A queueing network model is a good analytical approach toward business process analysis and design, and can provide a useful abstraction of a business process. However, the existing queueing network models were developed based on telephone systems or applied to manufacturing processes in which machine servers dominate the system. In a business process, the servers are usually people. The characteristics of human servers should be taken into account by the queueing model, i.e. specialization and coordination. ^ The research described in this dissertation develops an open queueing network model to do a quick analysis of business processes. Additionally, optimization models are developed to provide optimal business process designs. The queueing network model extends and improves upon existing multi-class open-queueing network models (MOQN) so that the customer flow in the human-server oriented processes can be modeled. The optimization models help business process designers to find the optimal design of a business process with consideration of specialization and coordination. ^ The main findings of the research are, first, parallelization can reduce the cycle-time for those customer classes that require more than one parallel activity; however, the coordination time due to the parallelization overwhelms the savings from parallelization under the high utilization servers since the waiting time significantly increases, thus the cycle-time increases. Third, the level of industrial technology employed by a company and coordination time to mange the tasks have strongest impact on the business process design; as the level of industrial technology employed by the company is high; more division is required to improve the cycle-time; as the coordination time required is high; consolidation is required to improve the cycle-time. ^

Geographic provenancing of unprocessed cotton using elemental analysis and stable isotope ratios

Cotton is the most abundant natural fiber in the world. Many countries are involved in the growing, importation, exportation and production of this commodity. Paper documentation claiming geographic origin is the current method employed at U.S. ports for identifying cotton sources and enforcing tariffs. Because customs documentation can be easily falsified, it is necessary to develop a robust method for authenticating or refuting the source of the cotton commodities. This work presents, for the first time, a comprehensive approach to the chemical characterization of unprocessed cotton in order to provide an independent tool to establish geographic origin. Elemental and stable isotope ratio analysis of unprocessed cotton provides a means to increase the ability to distinguish cotton in addition to any physical and morphological examinations that could be, and are currently performed. Elemental analysis has been conducted using LA-ICP-MS, LA-ICP-OES and LIBS in order to offer a direct comparison of the analytical performance of each technique and determine the utility of each technique for this purpose. Multivariate predictive modeling approaches are used to determine the potential of elemental and stable isotopic information to aide in the geographic provenancing of unprocessed cotton of both domestic and foreign origin. These approaches assess the stability of the profiles to temporal and spatial variation to determine the feasibility of this application. This dissertation also evaluates plasma conditions and ablation processes so as to improve the quality of analytical measurements made using atomic emission spectroscopy techniques. These interactions, in LIBS particularly, are assessed to determine any potential simplification of the instrumental design and method development phases. This is accomplished through the analysis of several matrices representing different physical substrates to determine the potential of adopting universal LIBS parameters for 532 nm and 1064 nm LIBS for some important operating parameters. A novel approach to evaluate both ablation processes and plasma conditions using a single measurement was developed and utilized to determine the "useful ablation efficiency" for different materials. The work presented here demonstrates the potential for an a priori prediction of some probable laser parameters important in analytical LIBS measurement.

Development and evaluation of a geographic information system based method to estimate flooding susceptibility in an area of Broward County, Florida

The objective of this study was to develop a GIS-based multi-class index overlay model to determine areas susceptible to inland flooding during extreme precipitation events in Broward County, Florida. Data layers used in the method include Airborne Laser Terrain Mapper (ALTM) elevation data, excess precipitation depth determined through performing a Soil Conservation Service (SCS) Curve Number (CN) analysis, and the slope of the terrain. The method includes a calibration procedure that uses "weights and scores" criteria obtained from Hurricane Irene (1999) records, a reported 100-year precipitation event, Doppler radar data and documented flooding locations. Results are displayed in maps of Eastern Broward County depicting types of flooding scenarios for a 100-year, 24-hour storm based on the soil saturation conditions. As expected the results of the multi-class index overlay analysis showed that an increase for the potential of inland flooding could be expected when a higher antecedent moisture condition is experienced. The proposed method proves to have some potential as a predictive tool for flooding susceptibility based on a relatively simple approach.

The design, implementation and production process of creating a viable series of Latin shows in Hollywood, Florida

The purpose of this research was to design and implement a Series of Latin Shows to be featured at the Satine Restaurant located in The Diplomat Hotel in Hollywood, Florida. Three shows were created: "Electro Tango," "Bossa Nova Jazz," and "Piel Canela Night" to help generate interest for not only the Satine Restaurant but also for the surrounding area. The artistic concept included big bands, costumes, dancers and a DJ. A production book was created and included the most important aspects of the individual shows such as budgets, costumes, and ground plans, to assure the success of each event. Careful analysis was done for the demographic area and a marketing plan was designed and implemented. The research and practical application of similar shows in the industry determined that the production of these particular shows, although costly, have a qualifiable chance to succeed in this venue.

Geographic Provenancing of Unprocessed Cotton Using Elemental Analysis and Stable Isotope Ratios

Cotton is the most abundant natural fiber in the world. Many countries are involved in the growing, importation, exportation and production of this commodity. Paper documentation claiming geographic origin is the current method employed at U.S. ports for identifying cotton sources and enforcing tariffs. Because customs documentation can be easily falsified, it is necessary to develop a robust method for authenticating or refuting the source of the cotton commodities. This work presents, for the first time, a comprehensive approach to the chemical characterization of unprocessed cotton in order to provide an independent tool to establish geographic origin. Elemental and stable isotope ratio analysis of unprocessed cotton provides a means to increase the ability to distinguish cotton in addition to any physical and morphological examinations that could be, and are currently performed. Elemental analysis has been conducted using LA-ICP-MS, LA-ICP-OES and LIBS in order to offer a direct comparison of the analytical performance of each technique and determine the utility of each technique for this purpose. Multivariate predictive modeling approaches are used to determine the potential of elemental and stable isotopic information to aide in the geographic provenancing of unprocessed cotton of both domestic and foreign origin. These approaches assess the stability of the profiles to temporal and spatial variation to determine the feasibility of this application. This dissertation also evaluates plasma conditions and ablation processes so as to improve the quality of analytical measurements made using atomic emission spectroscopy techniques. These interactions, in LIBS particularly, are assessed to determine any potential simplification of the instrumental design and method development phases. This is accomplished through the analysis of several matrices representing different physical substrates to determine the potential of adopting universal LIBS parameters for 532 nm and 1064 nm LIBS for some important operating parameters. A novel approach to evaluate both ablation processes and plasma conditions using a single measurement was developed and utilized to determine the “useful ablation efficiency” for different materials. The work presented here demonstrates the potential for an a priori prediction of some probable laser parameters important in analytical LIBS measurement.