Joint-specific changes in locomotor complexity in the absence of muscle atrophy following incomplete spinal cord injury

ackground Following incomplete spinal cord injury (iSCI), descending drive is impaired, possibly leading to a decrease in the complexity of gait. To test the hypothesis that iSCI impairs gait coordination and decreases locomotor complexity, we collected 3D joint angle kinematics and muscle parameters of rats with a sham or an incomplete spinal cord injury. Methods 12 adult, female, Long-Evans rats, 6 sham and 6 mild-moderate T8 iSCI, were tested 4 weeks following injury. The Basso Beattie Bresnahan locomotor score was used to verify injury severity. Animals had reflective markers placed on the bony prominences of their limb joints and were filmed in 3D while walking on a treadmill. Joint angles and segment motion were analyzed quantitatively, and complexity of joint angle trajectory and overall gait were calculated using permutation entropy and principal component analysis, respectively. Following treadmill testing, the animals were euthanized and hindlimb muscles removed. Excised muscles were tested for mass, density, fiber length, pennation angle, and relaxed sarcomere length. Results Muscle parameters were similar between groups with no evidence of muscle atrophy. The animals showed overextension of the ankle, which was compensated for by a decreased range of motion at the knee. Left-right coordination was altered, leading to left and right knee movements that are entirely out of phase, with one joint moving while the other is stationary. Movement patterns remained symmetric. Permutation entropy measures indicated changes in complexity on a joint specific basis, with the largest changes at the ankle. No significant difference was seen using principal component analysis. Rats were able to achieve stable weight bearing locomotion at reasonable speeds on the treadmill despite these deficiencies. Conclusions Decrease in supraspinal control following iSCI causes a loss of complexity of ankle kinematics. This loss can be entirely due to loss of supraspinal control in the absence of muscle atrophy and may be quantified using permutation entropy. Joint-specific differences in kinematic complexity may be attributed to different sources of motor control. This work indicates the importance of the ankle for rehabilitation interventions following spinal cord injury.

The use of treatment theories and procedures for postural control in adult with hemiplegia: A national survey

This study investigated the use of treatment theories and procedures for postural control training used by Occupational Therapists (OTs) when working with hemiplegic adults who have had cerebrovascular accident (CVA) or traumatic brain injury (TBI). The method of data collection was a national survey of 400 randomly selected physical disability OTs with 127 usable surveys returned. Results showed that the most common used treatment theory was neurodevelopmental treatment (NDT), followed by motor relearning program (MRP), proprioceptive neuromuscular facilitation (PNF), Brunnstrom's approach, and the approach of Rood. The most common treatment posture used was sitting, followed by standing, mat activity, equilibrium reaction training, and walking. The factors affecting the use of various treatment theories procedures were years certified, years of clinical experience, work situation and work status. Pearson correlation coefficient analyses found significant positive relationships between treatment theories and postures. There were significant high correlations between usage of all pairs of treatment procedures. ^

Development of an open architecture motion control system

A multipurpose open architecture motion control system was developed with three platforms for control and monitoring. The Visual Basic user interface communicated with the operator and gave instructions to the electronic components. The first platform had a BASIC Stamp based controller and three stepping motors. The second platform had a controller, amplifiers and two DC servomotors. The third platform had a DSP module. In this study, each platform was used on machine tools either to move the table or to evaluate the incoming signal. The study indicated that by using advanced microcontrollers, which use high-level languages, motor controllers, DSPs (Digital Signal Processor) and microcomputers, the motion control of different systems could be realized in a short time. Although, the proposed systems had some limitations, their jobs were performed effectively. ^

Self-tuning algorithm for dsp-based motion control in cnc applications

This thesis describes the development of an adaptive control algorithm for Computerized Numerical Control (CNC) machines implemented in a multi-axis motion control board based on the TMS320C31 DSP chip. The adaptive process involves two stages: Plant Modeling and Inverse Control Application. The first stage builds a non-recursive model of the CNC system (plant) using the Least-Mean-Square (LMS) algorithm. The second stage consists of the definition of a recursive structure (the controller) that implements an inverse model of the plant by using the coefficients of the model in an algorithm called Forward-Time Calculation (FTC). In this way, when the inverse controller is implemented in series with the plant, it will pre-compensate for the modification that the original plant introduces in the input signal. The performance of this solution was verified at three different levels: Software simulation, implementation in a set of isolated motor-encoder pairs and implementation in a real CNC machine. The use of the adaptive inverse controller effectively improved the step response of the system in all three levels. In the simulation, an ideal response was obtained. In the motor-encoder test, the rise time was reduced by as much as 80%, without overshoot, in some cases. Even with the larger mass of the actual CNC machine, decrease of the rise time and elimination of the overshoot were obtained in most cases. These results lead to the conclusion that the adaptive inverse controller is a viable approach to position control in CNC machinery.

Evoking non-repertory verbal behavior across operant classes : the effects of motor echoic sign language training within the context of a motivating operation

The individual effects that echoic, mand, and sign language training procedures have on the acquisition of verbal behavior have been widely demonstrated, but more efficient strategies are still needed. This study combined all three treatment strategies into one treatment intervention in order to investigate the joint effects they may have on verbal behavior. Six participants took part in the study. Intervention totaled 1 hour/day for 5 days/week until mastery criterion for motor echoic behavior was achieved. Although motor echoic behavior were solely targeted for acquisition, significant increases in spontaneous motor mands were noted in all treatment participants. Additionally, 4 treatment participants also demonstrated significant gains in vocal echoics and spontaneous vocal mands. No significant increases were noted for the control participant. Results suggest that the aforementioned procedure may provide more efficient results as a first-step to teaching a functional repertoire of verbal behavior to developmentally delayed children.