Effects of roadway geometric features on run-off road crashes on the Florida State Highway System

Run-off-road (ROR) crashes have increasingly become a serious concern for transportation officials in the State of Florida. These types of crashes have increased proportionally in recent years statewide and have been the focus of the Florida Department of Transportation. The goal of this research was to develop statistical models that can be used to investigate the possible causal relationships between roadway geometric features and ROR crashes on Florida's rural and urban principal arterials. ^ In this research, Zero-Inflated Poisson (ZIP) and Zero-Inflated Negative Binomial (ZINB) Regression models were used to better model the excessive number of roadway segments with no ROR crashes. Since Florida covers a diverse area and since there are sixty-seven counties, it was divided into four geographical regions to minimize possible unobserved heterogeneity. Three years of crash data (2000–2002) encompassing those for principal arterials on the Florida State Highway System were used. Several statistical models based on the ZIP and ZINB regression methods were fitted to predict the expected number of ROR crashes on urban and rural roads for each region. Each region was further divided into urban and rural areas, resulting in a total of eight crash models. A best-fit predictive model was identified for each of these eight models in terms of AIC values. The ZINB regression was found to be appropriate for seven of the eight models and the ZIP regression was found to be more appropriate for the remaining model. To achieve model convergence, some explanatory variables that were not statistically significant were included. Therefore, strong conclusions cannot be derived from some of these models. ^ Given the complex nature of crashes, recommendations for additional research are made. The interaction of weather and human condition would be quite valuable in discerning additional causal relationships for these types of crashes. Additionally, roadside data should be considered and incorporated into future research of ROR crashes. ^

Investigation of the causes of serious injury and fatal crashes: An analysis using econometric models

The rate of fatal crashes in Florida has remained significantly higher than the national average for the last several years. The 2003 statistics from the National Highway Traffic Safety Administration (NHTSA), the latest available, show a fatality rate in Florida of 1.71 per 100 million vehicle-miles traveled compared to the national average of 1.48 per 100 million vehicle-miles traveled. The objective of this research is to better understand the driver, environmental, and roadway factors that affect the probability of injury severity in Florida. ^ In this research, the ordered logit model was used to develop six injury severity models; single-vehicle and two-vehicle crashes on urban freeways and urban principal arterials and two-vehicle crashes at urban signalized and unsignalized intersections. The data used in this research included all crashes that occurred on the state highway system for the period from 2001 to 2003 in the Southeast Florida region, which includes the Miami-Dade, Broward and Palm Beach Counties.^ The results of the analysis indicate that the age group and gender of the driver at fault were significant factors of injury severity risk across all models. The greatest risk of severe injury was observed for the age groups 55 to 65 and 66 and older. A positive association between injury severity and the race of the driver at fault was also found. Driver at fault of Hispanic origin was associated with a higher risk of severe injury for both freeway models and for the two-vehicle crash model on arterial roads. A higher risk of more severe injury crash involvement was also found when an African-American was the at fault driver on two-vehicle crashes on freeways. In addition, the arterial class was also found to be positively associated with a higher risk of severe crashes. Six-lane divided arterials exhibited the highest injury severity risk of all arterial classes. The lowest severe injury risk was found for one way roads. Alcohol involvement by the driver at fault was also found to be a significant risk of severe injury for the single-vehicle crash model on freeways. ^

Development of safety performance functions for empirical Bayes estimation of crash reduction factors

Crash reduction factors (CRFs) are used to estimate the potential number of traffic crashes expected to be prevented from investment in safety improvement projects. The method used to develop CRFs in Florida has been based on the commonly used before-and-after approach. This approach suffers from a widely recognized problem known as regression-to-the-mean (RTM). The Empirical Bayes (EB) method has been introduced as a means to addressing the RTM problem. This method requires the information from both the treatment and reference sites in order to predict the expected number of crashes had the safety improvement projects at the treatment sites not been implemented. The information from the reference sites is estimated from a safety performance function (SPF), which is a mathematical relationship that links crashes to traffic exposure. The objective of this dissertation was to develop the SPFs for different functional classes of the Florida State Highway System. Crash data from years 2001 through 2003 along with traffic and geometric data were used in the SPF model development. SPFs for both rural and urban roadway categories were developed. The modeling data used were based on one-mile segments that contain homogeneous traffic and geometric conditions within each segment. Segments involving intersections were excluded. The scatter plots of data show that the relationships between crashes and traffic exposure are nonlinear, that crashes increase with traffic exposure in an increasing rate. Four regression models, namely, Poisson (PRM), Negative Binomial (NBRM), zero-inflated Poisson (ZIP), and zero-inflated Negative Binomial (ZINB), were fitted to the one-mile segment records for individual roadway categories. The best model was selected for each category based on a combination of the Likelihood Ratio test, the Vuong statistical test, and the Akaike's Information Criterion (AIC). The NBRM model was found to be appropriate for only one category and the ZINB model was found to be more appropriate for six other categories. The overall results show that the Negative Binomial distribution model generally provides a better fit for the data than the Poisson distribution model. In addition, the ZINB model was found to give the best fit when the count data exhibit excess zeros and over-dispersion for most of the roadway categories. While model validation shows that most data points fall within the 95% prediction intervals of the models developed, the Pearson goodness-of-fit measure does not show statistical significance. This is expected as traffic volume is only one of the many factors contributing to the overall crash experience, and that the SPFs are to be applied in conjunction with Accident Modification Factors (AMFs) to further account for the safety impacts of major geometric features before arriving at the final crash prediction. However, with improved traffic and crash data quality, the crash prediction power of SPF models may be further improved.

Toward A Better Understanding of the Evolution of Hotel Development: A Discussion of Product-specific Lodging Demand

In his essay - Toward a Better Understanding of the Evolution of Hotel Development: A Discussion of Product-Specific Lodging Demand - by John A. Carnella, Consultant, Laventhol & Horwath, cpas, New York, Carnella initially describes his piece by stating: “The diversified hotel product in the united states lodging market has Resulted in latent room-night demand, or supply-driven demand resulting from the introduction of a lodging product which caters to a specific set of hotel patrons. The subject has become significant as the lodging market has moved toward segmentation with regard to guest room offerings. The author proposes that latent demand is a tangible, measurable phenomenon best understood in light of the history of the guest room product from its infancy to its present state.” The article opens with an ephemeral depiction of hotel development in the United States, both pre’ and post World War II. To put it succinctly, the author wants you to know that the advent of the inter-state highway system changed the complexion of the hotel industry in the U.S. “Two essential ingredients were necessary for the next phase of hotel development in this country. First was the establishment of the magnificently intricate infrastructure which facilitated motor vehicle transportation in and around the then 48 states of the nation,” says Carnella. “The second event…was the introduction of affordable highway travel. Carnella goes on to say that the next – big thing – in hotel evolution was the introduction of affordable air travel. “With the airways filled with potential lodging guests, developers moved next to erect a new genre of hotel, the airport hotel,” Carnella advances his picture. Growth progressed with the arrival of the suburban hotel concept, which wasn’t fueled by developments in transportation, but by changes in people’s living habits, i.e. suburban affiliations as opposed to urban and city population aggregates. The author explores the distinctions between full-service and limited service lodging operations. “The market of interest with consideration to the extended-stay facility is one dominated by corporate office parks,” Carnella proceeds. These evolutional states speak to latent demand, and even further to segmentation of the market. “Latent demand… is a product-generated phenomenon in which the number of potential hotel guests increases as the direct result of the introduction of a new lodging facility,” Carnella brings his unique insight to the table with regard to the specialization process. The demand is already there; just waiting to be tapped. In closing, “…there must be a consideration of the unique attributes of a lodging facility relative to its ability to attract guests to a subject market, just as there must be an examination of the property's ability to draw guests from within the subject market,” Carnella proposes.

Estimation of average annual daily traffic (AADT) using geographically weighted regression (GWR) method and geographic information system (GIS)

Annual average daily traffic (AADT) is important information for many transportation planning, design, operation, and maintenance activities, as well as for the allocation of highway funds. Many studies have attempted AADT estimation using factor approach, regression analysis, time series, and artificial neural networks. However, these methods are unable to account for spatially variable influence of independent variables on the dependent variable even though it is well known that to many transportation problems, including AADT estimation, spatial context is important. ^ In this study, applications of geographically weighted regression (GWR) methods to estimating AADT were investigated. The GWR based methods considered the influence of correlations among the variables over space and the spatially non-stationarity of the variables. A GWR model allows different relationships between the dependent and independent variables to exist at different points in space. In other words, model parameters vary from location to location and the locally linear regression parameters at a point are affected more by observations near that point than observations further away. ^ The study area was Broward County, Florida. Broward County lies on the Atlantic coast between Palm Beach and Miami-Dade counties. In this study, a total of 67 variables were considered as potential AADT predictors, and six variables (lanes, speed, regional accessibility, direct access, density of roadway length, and density of seasonal household) were selected to develop the models. ^ To investigate the predictive powers of various AADT predictors over the space, the statistics including local r-square, local parameter estimates, and local errors were examined and mapped. The local variations in relationships among parameters were investigated, measured, and mapped to assess the usefulness of GWR methods. ^ The results indicated that the GWR models were able to better explain the variation in the data and to predict AADT with smaller errors than the ordinary linear regression models for the same dataset. Additionally, GWR was able to model the spatial non-stationarity in the data, i.e., the spatially varying relationship between AADT and predictors, which cannot be modeled in ordinary linear regression. ^

Research-to-Practice (R2P) Tools for Improving Safety in Nighttime Highway Construction Work Zones

The safety of workers in nighttime roadway work zones has become a major concern for state transportation agencies due to the increase in the number of work zone fatalities. During the last decade, several studies have focused on the improvement of safety in nighttime roadway work zones; but the element that is still missing is a set of tools for translating the research results into practice. This paper discusses: 1) the importance of translating the research results related to the safety of workers and safety planning of nighttime work zones into practice, and 2) examples of tools that can be used for translating the results of such studies into practice. A tool that can propose safety recommendations in nighttime work zones and a web-based safety training tool for workers are presented in this paper. The tools were created as a component of a five-year research study on the assessment of the safety of nighttime roadway construction. The objectives of both tools are explained as well as their functionalities (i.e., what the tools can do for the users); their components (e.g., knowledge base, database, and interfaces); and their structures (i.e., how the components of the tools are organized to meet the objectives). Evaluations by the proposed users of each tool are also presented.

Dynamic Behavior and Fatigue Life of Highway Bridges Due to Doubling Heavy Vehicles

An increase in the demand for the freight shipping in the United States has been predicted for the near future and Longer Combination Vehicles (LCVs), which can carry more loads in each trip, seem like a good solution for the problem. Currently, utilizing LCVs is not permitted in most states of the US and little research has been conducted on the effects of these heavy vehicles on the roads and bridges. In this research, efforts are made to study these effects by comparing the dynamic and fatigue effects of LCVs with more common trucks. Ten Steel and prestressed concrete bridges with span lengths ranging from 30’ to 140’ are designed and modeled using the grid system in MATLAB. Additionally, three more real bridges including two single span simply supported steel bridges and a three span continuous steel bridge are modeled using the same MATLAB code. The equations of motion of three LCVs as well as eight other trucks are derived and these vehicles are subjected to different road surface conditions and bumps on the roads and the designed and real bridges. By forming the bridge equations of motion using the mass, stiffness and damping matrices and considering the interaction between the truck and the bridge, the differential equations are solved using the ODE solver in MATLAB and the results of the forces in tires as well as the deflections and moments in the bridge members are obtained. The results of this study show that for most of the bridges, LCVs result in the smallest values of Dynamic Amplification Factor (DAF) whereas the Single Unit Trucks cause the highest values of DAF when traveling on the bridges. Also in most cases, the values of DAF are observed to be smaller than the 33% threshold suggested by the design code. Additionally, fatigue analysis of the bridges in this study confirms that by replacing the current truck traffic with higher capacity LCVs, in most cases, the remaining fatigue life of the bridge is only slightly decreased which means that taking advantage of these larger vehicles can be a viable option for decision makers.

Effect of Pavement-Vehicle Interaction on Highway Fuel Consumption and Emission

Vehicle fuel consumption and emission are two important effectiveness measurements of sustainable transportation development. Pavement plays an essential role in goals of fuel economy improvement and greenhouse gas (GHG) emission reduction. The main objective of this dissertation study is to experimentally investigate the effect of pavement-vehicle interaction (PVI) on vehicle fuel consumption under highway driving conditions. The goal is to provide a better understanding on the role of pavement in the green transportation initiates. Four study phases are carried out. The first phase involves a preliminary field investigation to detect the fuel consumption differences between paired flexible-rigid pavement sections with repeat measurements. The second phase continues the field investigation by a more detailed and comprehensive experimental design and independently investigates the effect of pavement type on vehicle fuel consumption. The third study phase calibrates the HDM-IV fuel consumption model with data collected in the second field phase. The purpose is to understand how pavement deflection affects vehicle fuel consumption from a mechanistic approach. The last phase applies the calibrated HDM-IV model to Florida’s interstate network and estimates the total annual fuel consumption and CO2 emissions on different scenarios. The potential annual fuel savings and emission reductions are derived based on the estimation results. Statistical results from the two field studies both show fuel savings on rigid pavement compared to flexible pavement with the test conditions specified. The savings derived from the first phase are 2.50% for the passenger car at 112km/h, and 4.04% for 18-wheel tractor-trailer at 93km/h. The savings resulted from the second phase are 2.25% and 2.22% for passenger car at 93km/h and 112km/h, and 3.57% and 3.15% for the 6-wheel medium-duty truck at 89km/h and 105km/h. All savings are statistically significant at 95% Confidence Level (C.L.). From the calibrated HDM-IV model, one unit of pavement deflection (1mm) on flexible pavement can cause an excess fuel consumption by 0.234-0.311 L/100km for the passenger car and by 1.123-1.277 L/100km for the truck. The effect is more evident at lower highway speed than at higher highway speed. From the network level estimation, approximately 40 million gallons of fuel (combined gasoline and diesel) and 0.39 million tons of CO2 emission can be saved/reduced annually if all Florida’s interstate flexible pavement are converted to rigid pavement with the same roughness levels. Moreover, each 1-mile of flexible-rigid conversion can result in a reduction of 29 thousand gallons of fuel and 258 tons of CO2 emission yearly.