Characterization of ultra wideband antennas for personal communication devices using finite difference time domain technique

The current mobile networks don't offer sufficient data rates to support multimedia intensive applications in development for multifunctional mobile devices. Ultra wideband (UWB) wireless technology is being considered as the solution to overcome data rate bottlenecks in the current mobile networks. UWB is able to achieve such high data transmission rates because it transmits data over a very large chunk of the frequency spectrum. As currently approved by the U.S. Federal Communication Commission it utilizes 7.5 GHz of spectrum between 3.1 GHz and 10.6 GHz. ^ Successful transmission and reception of information data using UWB wireless technology in mobile devices, requires an antenna that has linear phase, low dispersion and a voltage standing wave ratio (VSWR) ≤ 2 throughout the entire frequency band. Compatibility with an integrated circuit requires an unobtrusive and electrically small design. The previous techniques that have been used to optimize the performance of UWB wireless systems, involve proper design of source pulses for optimal UWB performance. The goal of this work is directed towards the designing of antennas for personal communication devices, with optimal UWB bandwidth performance. Several techniques are proposed for optimal UWB bandwidth performance of the UWB antenna designs in this Ph.D. dissertation. ^ This Ph.D. dissertation presents novel UWB antenna designs for personal communication devices that have been characterized and optimized using the finite difference time domain (FDTD) technique. The antenna designs reported in this research are physically compact, planar for low profile use, with sufficient impedance bandwidth (>20%), antenna input impedance of 50-Ω, and an omni-directional (±1.5 dB) radiation pattern in the operating bandwidth. ^

Autonomic and embedded wireless sensor protocols for critical infrastructures

The tragic events of September 11th ushered a new era of unprecedented challenges. Our nation has to be protected from the alarming threats of adversaries. These threats exploit the nation's critical infrastructures affecting all sectors of the economy. There is the need for pervasive monitoring and decentralized control of the nation's critical infrastructures. The communications needs of monitoring and control of critical infrastructures was traditionally catered for by wired communication systems. These technologies ensured high reliability and bandwidth but are however very expensive, inflexible and do not support mobility and pervasive monitoring. The communication protocols are Ethernet-based that used contention access protocols which results in high unsuccessful transmission and delay. An emerging class of wireless networks, named embedded wireless sensor and actuator networks has potential benefits for real-time monitoring and control of critical infrastructures. The use of embedded wireless networks for monitoring and control of critical infrastructures requires secure, reliable and timely exchange of information among controllers, distributed sensors and actuators. The exchange of information is over shared wireless media. However, wireless media is highly unpredictable due to path loss, shadow fading and ambient noise. Monitoring and control applications have stringent requirements on reliability, delay and security. The primary issue addressed in this dissertation is the impact of wireless media in harsh industrial environment on the reliable and timely delivery of critical data. In the first part of the dissertation, a combined networking and information theoretic approach was adopted to determine the transmit power required to maintain a minimum wireless channel capacity for reliable data transmission. The second part described a channel-aware scheduling scheme that ensured efficient utilization of the wireless link and guaranteed delay. Various analytical evaluations and simulations are used to evaluate and validate the feasibility of the methodologies and demonstrate that the protocols achieved reliable and real-time data delivery in wireless industrial networks.

Enhancement of wireless networks with heterogeneous antennas

In recent years, wireless communication infrastructures have been widely deployed for both personal and business applications. IEEE 802.11 series Wireless Local Area Network (WLAN) standards attract lots of attention due to their low cost and high data rate. Wireless ad hoc networks which use IEEE 802.11 standards are one of hot spots of recent network research. Designing appropriate Media Access Control (MAC) layer protocols is one of the key issues for wireless ad hoc networks. ^ Existing wireless applications typically use omni-directional antennas. When using an omni-directional antenna, the gain of the antenna in all directions is the same. Due to the nature of the Distributed Coordination Function (DCF) mechanism of IEEE 802.11 standards, only one of the one-hop neighbors can send data at one time. Nodes other than the sender and the receiver must be either in idle or listening state, otherwise collisions could occur. The downside of the omni-directionality of antennas is that the spatial reuse ratio is low and the capacity of the network is considerably limited. ^ It is therefore obvious that the directional antenna has been introduced to improve spatial reutilization. As we know, a directional antenna has the following benefits. It can improve transport capacity by decreasing interference of a directional main lobe. It can increase coverage range due to a higher SINR (Signal Interference to Noise Ratio), i.e., with the same power consumption, better connectivity can be achieved. And the usage of power can be reduced, i.e., for the same coverage, a transmitter can reduce its power consumption. ^ To utilizing the advantages of directional antennas, we propose a relay-enabled MAC protocol. Two relay nodes are chosen to forward data when the channel condition of direct link from the sender to the receiver is poor. The two relay nodes can transfer data at the same time and a pipelined data transmission can be achieved by using directional antennas. The throughput can be improved significant when introducing the relay-enabled MAC protocol. ^ Besides the strong points, directional antennas also have some explicit drawbacks, such as the hidden terminal and deafness problems and the requirements of retaining location information for each node. Therefore, an omni-directional antenna should be used in some situations. The combination use of omni-directional and directional antennas leads to the problem of configuring heterogeneous antennas, i e., given a network topology and a traffic pattern, we need to find a tradeoff between using omni-directional and using directional antennas to obtain a better network performance over this configuration. ^ Directly and mathematically establishing the relationship between the network performance and the antenna configurations is extremely difficult, if not intractable. Therefore, in this research, we proposed several clustering-based methods to obtain approximate solutions for heterogeneous antennas configuration problem, which can improve network performance significantly. ^ Our proposed methods consist of two steps. The first step (i.e., clustering links) is to cluster the links into different groups based on the matrix-based system model. After being clustered, the links in the same group have similar neighborhood nodes and will use the same type of antenna. The second step (i.e., labeling links) is to decide the type of antenna for each group. For heterogeneous antennas, some groups of links will use directional antenna and others will adopt omni-directional antenna. Experiments are conducted to compare the proposed methods with existing methods. Experimental results demonstrate that our clustering-based methods can improve the network performance significantly. ^

Optimum wireless power transmission for sensors embedded in concrete

Various nondestructive testing (NDT) technologies for construction and performance monitoring have been studied for decades. Recently, the rapid evolution of wireless sensor network (WSN) technologies has enabled the development of sensors that can be embedded in concrete to monitor the structural health of infrastructure. Such sensors can be buried inside concrete and they can collect and report valuable volumetric data related to the health of a structure during and/or after construction. Wireless embedded sensors monitoring system is also a promising solution for decreasing the high installation and maintenance cost of the conventional wire based monitoring systems. Wireless monitoring sensors need to operate for long time. However, sensor batteries have finite life-time. Therefore, in order to enable long operational life of wireless sensors, novel wireless powering methods, which can charge the sensors’ rechargeable batteries wirelessly, need to be developed. The optimization of RF wireless powering of sensors embedded in concrete is studied here. First, our analytical results focus on calculating the transmission loss and propagation loss of electromagnetic waves penetrating into plain concrete at different humidity conditions for various frequencies. This analysis specifically leads to the identification of an optimum frequency range within 20–80 MHz that is validated through full-wave electromagnetic simulations. Second, the effects of various reinforced bar configurations on the efficiency of wireless powering are investigated. Specifically, effects of the following factors are studied: rebar types, rebar period, rebar radius, depth inside concrete, and offset placement. This analysis leads to the identification of the 902–928 MHz ISM band as the optimum power transmission frequency range for sensors embedded in reinforced concrete, since antennas working in this band are less sensitive to the effects of varying humidity as well as rebar configurations. Finally, optimized rectennas are designed for receiving and/or harvesting power in order to charge the rechargeable batteries of the embedded sensors. Such optimized wireless powering systems exhibit significantly larger efficiencies than the efficiencies of conventional RF wireless powering systems for sensors embedded in plain or reinforced concrete.

Periphyton light transmission relationships in Florida Bay and the Florida Keys, USA

Light transmission was measured through intact, submerged periphyton communities on artificial seagrass leaves. The periphyton communities were representative of the communities on Thalassia testudinum in subtropical seagrass meadows. The periphyton communities sampled were adhered carbonate sediment, coralline algae, and mixed algal assemblages. Crustose or film-forming periphyton assemblages were best prepared for light transmission measurements using artificial leaves fouled on both sides, while measurements through three-dimensional filamentous algae required the periphyton to be removed from one side. For one-sided samples, light transmission could be measured as the difference between fouled and reference artificial leaf samples. For two-sided samples, the percent periphyton light transmission to the leaf surface was calculated as the square root of the fraction of incident light. Linear, exponential, and hyperbolic equations were evaluated as descriptors of the periphyton dry weight versus light transmission relationship. Hyperbolic and exponential decay models were superior to linear models and exhibited the best fits for the observed relationships. Differences between the coefficients of determination (r2) of hyperbolic and exponential decay models were statistically insignificant. Constraining these models for 100% light transmission at zero periphyton load did not result in any statistically significant loss in the explanatory capability of the models. In most all cases, increasing model complexity using three-parameter models rather than two-parameter models did not significantly increase the amount of variation explained. Constrained two-parameter hyperbolic or exponential decay models were judged best for describing the periphyton dry weight versus light transmission relationship. On T. testudinum in Florida Bay and the Florida Keys, significant differences were not observed in the light transmission characteristics of the varying periphyton communities at different study sites. Using pooled data from the study sites, the hyperbolic decay coefficient for periphyton light transmission was estimated to be 4.36 mg dry wt. cm−2. For exponential models, the exponential decay coefficient was estimated to be 0.16 cm2 mg dry wt.−1.

Progress towards Elimination of HIV Mother-to-Child Transmission in the Dominican Republic from 1999 to 2011

In 1999, prevention of mother-to-child transmission (pMTCT) using antiretrovirals was introduced in the Dominican Republic (DR). Highly active antiretroviral therapy (HAART) was introduced for immunosuppressed persons in 2004 and for pMTCT in 2008. To assess progress towards MTCT elimination, data from requisitions for HIV nucleic acid amplification tests for diagnosis of HIV infection in perinatally exposed infants born in the DR from 1999 to 2011 were analyzed. The MTCT rate was 142/1,274 (11.1%) in 1999–2008 and 12/302 (4.0%) in 2009–2011 (), with a rate of 154/1,576 (9.8%) for both periods combined. This decline was associated with significant increases in the proportions of women who received prenatal HAART (from 12.3% to 67.9%) and infants who received exclusive formula feeding (from 76.3% to 86.1%) and declines in proportions of women who received no prenatal antiretrovirals (from 31.9% to 12.2%) or received only single-dose nevirapine (from 39.5% to 19.5%). In 2007, over 95% of DR pregnant women received prenatal care, HIV testing, and professionally attended delivery. However, only 58% of women in underserved sugarcane plantation communities (2007) and 76% in HIV sentinel surveillance hospitals (2003–2005) received their HIV test results. HIV-MTCT elimination is feasible but persistent lack of access to critical pMTCT measures must be addressed.

Syndemic health disparities and resilience processes related to HIV transmission risk among African American/Black men in south Florida

Rates of HIV infection continue to climb among minority populations and men who have sex with men (MSM), with African American/Black MSM being especially impacted. Numerous studies have found HIV transmission risk to be associated with many health and social disparities resulting from larger environmental and structural forces. Using anthropological and social environment-based theories of resilience that focus on individual agency and larger social and environmental structures, this dissertation employed a mixed methods design to investigate resilience processes among African American/Black MSM.^ Quantitative analyses compared African American/Black (N=108) and Caucasian/White (N=250) MSM who participated in a previously conducted randomized controlled trial (RCT) of sexual and substance use risk reduction interventions. At RCT study entry, using past 90 day recall periods, there were no differences in unprotected sex frequency, however African American/Black MSM reported higher frequencies of days high (P<0.000), and drugs and sex used in combination (P<0.000), and substance dependence (P<0.000) and lower levels of social support (P<0.024) compared to Caucasian/White MSM. At 12- month follow-up, multi-level statistical models found that African American/Black MSM reduced their frequencies of days high and unprotected sex at greater rates than Caucasian/White MSM (P<0.001).^ Qualitative data collected among a sub-sample of African American/Black MSM from the RCT (N=21) described the men's experiences of living with multiple health and social disparities and the importance of RCT study assessments in facilitating reductions in risk behaviors. A cross-case analysis showed different resilience processes undertaken by men who experienced low socioeconomic status, little family support, and homophobia (N=16) compared to those who did not (N=5).^ The dissertation concludes that resilience processes to HIV transmission risk and related health and social disparities among African American/Black MSM varies and are dependent on specific social environmental factors, including social relationships, structural homophobia, and access to social, economic, and cultural capital. Men define for themselves what it means to be resilient within their social environment. These conclusions suggest that both individual and structural-level resilience-based HIV prevention interventions are needed.^

Pulsed parabolic equation model of acoustic transmission (PPEMAT)

Underwater sound is very important in the field of oceanography where it is used for remote sensing in much the same way that radar is used in atmospheric studies. One way to mathematically model sound propagation in the ocean is by using the parabolic-equation method, a technique that allows range dependent environmental parameters. More importantly, this method can model sound transmission where the source emits either a pure tone or a short pulse of sound. Based on the parabolic approximation method and using the split-step Fourier algorithm, a computer model for underwater sound propagation was designed and implemented. This computer model differs from previous models in its use of the interactive mode, structured programming, modular design, and state-of-the-art graphics displays. In addition, the model maximizes the efficiency of computer time through synchronization of loosely coupled dual processors and the design of a restart capability. Since the model is designed for adaptability and for users with limited computer skills, it is anticipated that it will have many applications in the scientific community.

A novel lossless compression technique for text data

The focus of this thesis is placed on text data compression based on the fundamental coding scheme referred to as the American Standard Code for Information Interchange or ASCII. The research objective is the development of software algorithms that result in significant compression of text data. Past and current compression techniques have been thoroughly reviewed to ensure proper contrast between the compression results of the proposed technique with those of existing ones. The research problem is based on the need to achieve higher compression of text files in order to save valuable memory space and increase the transmission rate of these text files. It was deemed necessary that the compression algorithm to be developed would have to be effective even for small files and be able to contend with uncommon words as they are dynamically included in the dictionary once they are encountered. A critical design aspect of this compression technique is its compatibility to existing compression techniques. In other words, the developed algorithm can be used in conjunction with existing techniques to yield even higher compression ratios. This thesis demonstrates such capabilities and such outcomes, and the research objective of achieving higher compression ratio is attained.

Syndemic Health Disparities and Resilience Processes Related to HIV Transmission Risk among African American/Black Men in South Florida

Rates of HIV infection continue to climb among minority populations and men who have sex with men (MSM), with African American/Black MSM being especially impacted. Numerous studies have found HIV transmission risk to be associated with many health and social disparities resulting from larger environmental and structural forces. Using anthropological and social environment-based theories of resilience that focus on individual agency and larger social and environmental structures, this dissertation employed a mixed methods design to investigate resilience processes among African American/Black MSM. Quantitative analyses compared African American/Black (N=108) and Caucasian/White (N=250) MSM who participated in a previously conducted randomized controlled trial (RCT) of sexual and substance use risk reduction interventions. At RCT study entry, using past 90 day recall periods, there were no differences in unprotected sex frequency, however African American/Black MSM reported higher frequencies of days high (P Qualitative data collected among a sub-sample of African American/Black MSM from the RCT (N=21) described the men’s experiences of living with multiple health and social disparities and the importance of RCT study assessments in facilitating reductions in risk behaviors. A cross-case analysis showed different resilience processes undertaken by men who experienced low socioeconomic status, little family support, and homophobia (N=16) compared to those who did not (N=5). The dissertation concludes that resilience processes to HIV transmission risk and related health and social disparities among African American/Black MSM varies and are dependent on specific social environmental factors, including social relationships, structural homophobia, and access to social, economic, and cultural capital. Men define for themselves what it means to be resilient within their social environment. These conclusions suggest that both individual and structural-level resilience-based HIV prevention interventions are needed.