Preparação de catalisadores para reações de esterificação do ácido oleico baseados em matrizes polímericas sulfonadas POLI(1- FENILETILENO) (PS) e POLI(1-CLOROETILENO) (PVC)

Chemical modification of polymer matrices is an alternative way to change its surface properties. The introduction of sulfonic acid groups in polymer matrices alter properties such as adhesion, wettability, biocampatibility, catalytic activity, among others. This paper describes the preparation of polymeric solid acid based on the chemical modification of poly (1-fenietileno) (PS) and Poly (1-chloroethylene) (PVC) by the introduction of sulfonic acid groups and the application of these polymers as catalysts in the esterification reaction of oleic acid with methanol. The modified materials were characterized by Infrared Spectroscopy, Elemental Analysis and titration acid-base of the acid groups. All techniques confirmed the chemical changes and the presence of sulfur associated with sulfonic acid groups or sulfates. The modified polymers excellent performance in the esterification reaction of oleic acid with methanol a degree of conversion higher than 90% for all investigated polymers (modified PS and PVC (5% w / w)), with a mass ratio of oleic acid: methanol 1:10 to 100 ° C. The best performance was observed for the modified PVC catalyst (PVCS) which showed low degree of swelling during the reactions is recovered by filtration different from that observed for polystyrene sulfonate (PSS). Given these facts, the PVCS was employed as a catalyst in the esterification reaction of oleic acid in different times and different temperatures to obtain the kinetic parameters of the reaction. Experimental data show a great fit for pseudo-homogeneous model of second order and activation energy value of 41.12 kJ mol -1, below that found in the literature for the uncatalyzed reaction, 68.65 kJ mol -1 .The PVCS exhibits good catalytic activity for 3 times of reuse, with a slight decrease in the third cycle, but with a conversion of about 78%. The results show that solid polymeric acid has good chemical stability for the application in esterification reaction of commercial importance with possible application in the biodiesel production. The advantages in use of this system are the increased reaction rate at about 150 times, at these test conditions, the replacement of sulfuric acid as a catalyst for this being the most corrosive and the possibility of reuse of the polymer for several cycles.

Obtenção de triacetato de celulose a partir do bagaço de cana-deaçúcar para revestimento de micropartículas de goma gelana e avaliação do seu perfil de liberação in vitro e da mucoadesão ex vivo

Oral route of administration is considered to be the most comfortable, safe and greater adaptation for patients. But, oral route presents some disadvantages such as drugs bioavailability and side effects on the stomach. Some technologies are studied to soften and/or resolve these problems, such as coating with polymeric films, which are able to protect the pharmaceutical form of the acid stomachic environment and to act in the drug release, and mucoadhesive systems, which allow the pharmaceutical form remains a greater time interval in the intestine, increasing the effectiveness of the drug. Cellulose triacetate (CTA) films were produced from cellulose extracted from sugar cane bagasse. The films were prepared with different morphologies (with and without water, acting as non-solvent) and concentrations (3, 6.5 and 10%) of CTA and characterized using scanning electron microscopy (SEM), water vapor permeability (WVP), puncture resistance (PR), enzymatic digestion (DE), and mucoadhesive force evaluation (MF). Microscopy showed the formation of symmetric and asymmetric morphologies. WVP data showed that more concentrated films have higher values for WVP; moreover, asymmetric films had higher values than symmetric films. PR measurements showed that symmetric membranes are more resistant than asymmetric ones. More concentrated films were also more puncture resistant, except for symmetric membranes with CTA concentrations of 6.5 and 10% that did not show significant differences. All of the films presented large mucoadhesive capacities independent of their morphology and CTA concentration. From the results of WVP and RP, a symmetric filme with 6.5% CTA showed better ability and mechanical resistance, therefore, was selected to serve as coating of gellan gum (GG) particles incorporating ketoprofen (KET), which was confirmed by SEM. The selected film presented low values in measurements of the swelling index (SI) and in a dissolution test (DT). TGA analysis showed that the CTA coating does not influence the thermal stability of the particles and there is no incompatibility evidence between CTA, GG and KET. Coated particles released 100% of the ketoprofen in 24 h, while uncoated particles released the same amount in 4 h. The results of this study highlight the potential of CTA in the development of new controlled oral delivery systems.