Aditivo polimérico derivado de fonte renovável para aplicação em cimento asfáltico de petróleo

This study evaluated the effects of incorporating an additive from an agro-industrial residue, after some chemical modification reactions, to petroleum asphalt cement (CAP) through the polymerization reaction of a viscous polyol obtained by bagasse biomass oxypropylation reaction sugarcane with anhydrides. The polyol is obtained by biomass oxypropylation reaction with propylene oxide, the reaction was performed in an autoclave sealed with pressure and temperature control using 25 mL of OP for every 5 grams of biomass 200°C, which time reaction was two hours. The reaction is revealed by varying the system pressure, initially at atmospheric pressure to reach a maximum pressure value and its subsequent return to atmospheric pressure. For the choice of the most suitable reaction time for polymerization of the polyol with pyromellitic anhydride, the reaction was also conducted in an autoclave sealed with temperature controller (150 ° C) using 20 g of polyol, 1 g of sodium acetate (catalyst) and 8 g of pyromellitic anhydride with the times 30 and 60 minutes. The polymerized materials with different times were characterized by determining the relative viscosity and percentage content of extractable in cyclohexane / ethanol. Given the results with the polymerized material 30 minutes showed the lowest percentage content of extractives and an increased viscosity relative indicating that this time is highlighted with respect to time 60 minutes, because the material is possibly in the form of a crosslinked polymer. Given the choice of time of 30 minutes other polymerization reactions were performed with various anhydrides and other conditions employed different proportions by mass of polyol anhydrides we were referred to as condition I (20 g anhydride and 8 g of polyol), II (20 g anhydride and 20 g of polyol) and III (8 g anhydride and 20 g of polyol). The FTIR spectra of polymeric materials with different polymerization conditions used to prove the occurrence of chemical modification due to the appearance of a characteristic band ester groups (1750 cm-1) present in the polymerized material. He chose to work with the condition III, as is the condition which employs a larger amount of polyol, and even with the smaller amount of anhydride used FTIR spectra revealed that the polymerization reaction was performed. Among the various anhydrides (phthalic, maleic and pyromellitic) of the different conditions used that stood out before the solubility test with solvents analyzed was polymerized material with pyromellitic anhydride because the polymerized material likely in the form of a crosslinked polymer because it was insoluble or poorly soluble in the solvents tested. Polymerization of the polyol with pyromellitic anhydride using condition III, that is, BCPP30, CSPP30, PCPP30 e BCPPG30, provided an increase in thermal stability relative to material in the form of polyol. Applicability tests concerning the incorporation of 16% m / m BCPP30, CSPP30, PCPP30 e BCPPG30 additive in relation to the mass of 600 g CAP showed through characterization tests used, softening point, elastic recovery and marshall dosage, it is possible to use BCPP30 as an additive the conventional CAP, because even with the incorporation of this new additive modified CAP met the specifications of the appropriate standard.

Inter-relação entre lesão cervical não cariosa e comprometimento periodontal: diagnóstico, tratamento e previsibilidade - estudo clínico prospectivo e laboratorial

The coexistence of gingival recession (GR) with root coverage indication and non-carious cervical lesions (LCNC) generates the need for a protocol that respects and promotes health of dental and periodontal tissues and allows treatment predictability. The main objectives of this theses were: (1) verify, through clinical evaluations, the connective tissue graft for root coverage on direct and indirect restorations made of ceramic resin; (2) analyze the influence of the battery level of the LED curing unit in the composite resin characteristics; (3) assess the influence of restorative materials, composite resin and ceramics, on the viability of gingival fibroblasts from primary culture. Nine patients with good oral hygiene and occlusal stability diagnosed with LCNCs the anterior teeth including premolars associated with gingival recession (class I and II of Miller) and only gingival recession were selected. After initial clinical examination, occlusal adjustment was performed and the patients had their teeth randomized allocated on direct composite resin restoration of LCNC, polishing and GR treatment with connective tissue graft and advanced coronally flap CR group (n = 15); and indirect ceramic restoration of the LCNC's and GR treatment (CTG+CAF) Group C (n = 15). The GR presented teeth with no clinically formed LCNCs cavity were treated using (CTG+CAF) being the control group (n = 15). Sorption and solubility tests, analysis of the degree of conversion and diametral tensile strength were performed in composite resin samples (n = 10) photoactivated by 100, 50 and 10% battery charge LED unit. The viability of fibroblasts on composite resin, ceramics and dentin disks (n = 3) was examined. Clinical follow-up was performed for three months. The data obtained at different stages were tabulated and subjected to analysis for detection of normal distribution and homogeneity. The results showed that: the LED unit with 10% battery affects the characteristics of the composite resin; restorative materials present biocompatibility with gingival fibroblasts; and the association of surgical and restorative treatment of teeth affected by NCCL and GR presents successful results at 3-month follow-up.