Infecções por enterobacteriaceae resistente aos carbapenêmicos em hospital de ensino: epidemiologia e caracterização molecular

Introduction: The production of KPC (Klebsiella pneumoniae carbapenemase) has become an important mechanism of carbapenem-resistance among Enterobacteriaceae strains. In Brazil, KPC is already widespread and its incidence has increased significantly, reducing treatment options. The “perfect storm” combination of the absence of new drug developmentand the emergence of multidrug-resistant strains resulted in the need for the use of older drugs, with greater toxicity, such as polymyxins. Aims: To determine the occurrence of carbapenemase-producing strains in carbapenem-resistant Enterobacteriaceae isolated from patients with nosocomial infection/colonization during September/2014 to August/2015, to determine the risk factors associated with 30-day- mortality and the impact of inappropriate therapy. Materials and Methods: We performed a case control study to assess the risk factors (comorbidities, invasive procedures and inappropriate antimicrobial therapy) associated with 30-day-mortality, considering the first episode of infection in 111 patients. The resistance genes blaKPC, blaIMP, blaVIM and blaNDM-1 were detected by polymerase chain reaction technique. Molecular typing of the strains involved in the outbreak was performed by pulsed field gel electrophoresis technique. The polymyxin resistance was confirmed by the microdilution broth method. Results: 188 episodes of carbapenem-resistant Enterobacteriaceae infections/colonizations were detected; of these, 122 strains were recovered from the hospital laboratory. The presence of blaKPC gene were confirmed in the majority (74.59%) of these isolates. It was not found the presence of blaIMP , blaVIM and blaNDM-1 genes. K. pneumoniae was the most frequent microorganism (77,13%), primarily responsible for urinary tract infections (21,38%) and infections from patients of the Intensive Care Unit (ICU) (61,38%). Multivariate statistical analysis showed as predictors independently associated with mortality: dialysis and bloodstream infection. The Kaplan-Meier curve showed a lower probability of survival in the group of patients receiving antibiotic therapy inappropriately. Antimicrobial use in adult ICU varied during the study period, but positive correlation between increased incidence of strains and the consumption was not observed. In May and July 2015, the occurrence rates of carbapenem-resistant Enterobacteriaceae KPC-producing per 1000 patient-days were higher than the control limit established, confirming two outbreaks, the first caused by colistin-susceptible KPC-producing K. pneumoniae isolates, with a polyclonal profile and the second by a dominant clone of colistin-resistant (≥ 32 μg/mL) KPC-producing K. pneumoniae. The cross transmission between patients became clear by the temporal and spatial relationships observed in the second outbreak, since some patients occupied the same bed, showing problems in hand hygiene adherence among healthcare workers and inadequate terminal disinfection of environment. The outbreak was contained when the ICU was closed to new admissions. Conclusions: The study showed an endemicity of K. pneumoniae KPC-producing in adult ICU, progressing to an epidemic monoclonal expansion, resulted by a very high antibiotic consumption of carbapenems and polymyxins and facilitated by failures in control measures the unit.

Fontes de matéria orgânica para a formulação de fertilizantes organominerais peletizados no desenvolvimento da cultura do sorgo

Organo-mineral fertilizers have been used to both meet plants’ nutritional needs and reduce producers’ reliance on mineral fertilizers. This practice improves both the use of nutrients by plants and the soil structure due to the organic matter in these fertilizers. This study aimed to determine the effect of organic matter sources in the composition of organomineral fertilizers and compare it to the effect of traditional mineral fertilizers when it comes to the initial development of sorghum. Research was carried out in a greenhouse at the Federal University of Uberlandia, in Uberlandia, Minas Gerais, Brazil. Sorghum seeds of grain-bearing simple hybrid 1G100 were used in the seeding process. The experiment followed a randomized complete block design in a 4 x 3 + 2 factorial arrangement. Factors included four levels (50, 75, 100 and 125% of 450 kg ha-1, which is the recommended dose for sorghum crops), three organic matter sources in the composition of the organomineral fertilizers (sewage sludge, filter cake, and peat), a control (100% mineral fertilizer), and an untreated check (no fertilizers). Each experimental plot consisted of four plants divided into two pots. Oxisol was used in all pots. Analyses were performed at 30 and 60 days after seeding (DAS) and targeted: plant height, stem diameter, chlorophyll A, chlorophyll B, and leaf area. After this period, plants were removed from the soil, and had their aerial parts isolated to be dried in an air-forced oven before measurement of their dry mass. Means of the organomineral fertilizers outperformed those of both control and untreated check plots in almost all variables at 30 DAS. The only exception was variable stem diameter, in which organomineral fertilizers outperformed untreated check plots only. Sorghum fertilized with organomineral fertilizers also showed positive results in the variables analyzed at 60 DAS: even with dose reduction, their means were similar to those found in control plots. Organomineral fertilizers had higher means in some variables, such as diameter and dry mass of the aerial part, than both control and untreated check plots. In the conditions set in this study and considering the variables herein reported, organomineral fertilizers can substitute mineral fertilizers in the initial development of sorghum, even with some dose reductions.

A noção de sistema na fundação da linguística moderna

This work is intended to investigate the saussurian notion of system. Such a notion is fundamental to Ferdinand de Saussure's theorization, since it composes the definition of "langue", as he thought it. This definition was crucial to the delimitation of linguistics' specific object of study, which granted its place among modern sciences. However, the notion of system was not created by Saussure. Not only in Linguistics, but also in other areas, this notion appeared in very ancient studies, mingling with the establishment of man in society and the development of their economic and organizational activities. Specifically, in the context of language studies, the system consists in a notion that composed the work of the first grammarians in the West, in ancient Greece. Moreover, this notion was also used afterwards, in the synonymy studies and in the comparative analysis of languages, developed by scholars of the nineteenth century. Nevertheless, although Saussure had had his formation in Leipzig and Berlim, amid comparatists studies, his notion of system is an innovation, while is also continuing. In light of this, we aim to highlight the aspects of the saussurian notion of system that allow the establishment of a relationship of continuity and rupture with other conceptions of system. For that, we will investigate four Saussure authored documents: the « Cours de linguistique générale », the « Mémoire sur le système primitif des voyelles dans les langues indo-européennes », and the two sets of manuscripts « De l'essence double du langage » and « Notes pour le cours III ».

Seleção de características para identificação de diferentes proporções de tipos de fibras musculares por meio da eletromiografia de superfície

Skeletal muscle consists of muscle fiber types that have different physiological and biochemical characteristics. Basically, the muscle fiber can be classified into type I and type II, presenting, among other features, contraction speed and sensitivity to fatigue different for each type of muscle fiber. These fibers coexist in the skeletal muscles and their relative proportions are modulated according to the muscle functionality and the stimulus that is submitted. To identify the different proportions of fiber types in the muscle composition, many studies use biopsy as standard procedure. As the surface electromyography (EMGs) allows to extract information about the recruitment of different motor units, this study is based on the assumption that it is possible to use the EMG to identify different proportions of fiber types in a muscle. The goal of this study was to identify the characteristics of the EMG signals which are able to distinguish, more precisely, different proportions of fiber types. Also was investigated the combination of characteristics using appropriate mathematical models. To achieve the proposed objective, simulated signals were developed with different proportions of motor units recruited and with different signal-to-noise ratios. Thirteen characteristics in function of time and the frequency were extracted from emulated signals. The results for each extracted feature of the signals were submitted to the clustering algorithm k-means to separate the different proportions of motor units recruited on the emulated signals. Mathematical techniques (confusion matrix and analysis of capability) were implemented to select the characteristics able to identify different proportions of muscle fiber types. As a result, the average frequency and median frequency were selected as able to distinguish, with more precision, the proportions of different muscle fiber types. Posteriorly, the features considered most able were analyzed in an associated way through principal component analysis. Were found two principal components of the signals emulated without noise (CP1 and CP2) and two principal components of the noisy signals (CP1 and CP2 ). The first principal components (CP1 and CP1 ) were identified as being able to distinguish different proportions of muscle fiber types. The selected characteristics (median frequency, mean frequency, CP1 and CP1 ) were used to analyze real EMGs signals, comparing sedentary people with physically active people who practice strength training (weight training). The results obtained with the different groups of volunteers show that the physically active people obtained higher values of mean frequency, median frequency and principal components compared with the sedentary people. Moreover, these values decreased with increasing power level for both groups, however, the decline was more accented for the group of physically active people. Based on these results, it is assumed that the volunteers of the physically active group have higher proportions of type II fibers than sedentary people. Finally, based on these results, we can conclude that the selected characteristics were able to distinguish different proportions of muscle fiber types, both for the emulated signals as to the real signals. These characteristics can be used in several studies, for example, to evaluate the progress of people with myopathy and neuromyopathy due to the physiotherapy, and also to analyze the development of athletes to improve their muscle capacity according to their sport. In both cases, the extraction of these characteristics from the surface electromyography signals provides a feedback to the physiotherapist and the coach physical, who can analyze the increase in the proportion of a given type of fiber, as desired in each case.

O problema mente-corpo na psicologia fenomenológica de Edith Stein : implicações para uma fundamentação da ciência psicológica

Psychology is a relatively new scientific branch and still lacks consistent methodological foundation to support its investigations. Given its immaturity, this science finds difficulties to delimit its ontological status, which spawnes several epistemological and methodological misconceptions. Given this, Psychology failed to demarcate precisely its object of study, leading, thus, the emergence of numerous conceptions about the psychic, which resulted in the fragmentation of this science. In its constitution, psychological science inherited a complex philosophical problem: the mind-body issue. Therefore, to define their status, Psychology must still face this problem, seeking to elucidate what is the mind, the body and how they relate. In light of the importance of this issue to a strict demarcation of psychological object, it was sought in this research, to investigate the mind-body problem in the Phenomenological Psychology of Edith Stein (1891-1942), phenomenologist philosopher who undertook efforts for a foundation of Psychology. For that, the discussion was subsidized from the contributions of the Philosophy of Mind and the support of the phenomenological method to the mind-body problem. From there, by a qualitative bibliographical methodology, it sought to examine the problem of research through the analysis of some philosophical-psychological philosopher's works, named: "Psychic Causality” (Kausalität Psychische, 1922) and “Introduction to Philosophy" (Einführung in die Philosophie, 1920). For this investigation, it was made, without prejudice to the discussion, a terminological equivalence between the terms mind and psyche, as the philosopher used the latter to refer to the object of Psychology. It sought to examine, therefore, how Stein conceived the psyche, the body and the relationship between them. Although it wasn't the focus of the investigation, it also took into account the spiritual dimension, as the philosopher conceived the human person as consisting of three dimensions: body, psyche and spirit. Given this, Stein highlighted the causal mechanism of the psyche, which is based on the variations of the vital force that emerges from the vital sphere. In relation to the corporeal dimension, the philosopher, following the analysis of Edmund Husserl (1859-1938), highlighted the dual aspect of the body, because it is at the same time something material (Körper) and also a linving body (Leib). On the face of it, it is understood that the psyche and the body are closely connected, so that it constitutes a dual-unit which is manifested in the Leib. This understanding of the problem psyche-mind/body provides a rich analysis of this issue, enabling the overcoming of some inconsistencies of the monistic and dualistic positions. Given this, it allows a strict elucidation of the Psychology object, contributing to the foundation of this science.

Efeito da oxigenação hiperbárica no reparo ósseo de ratos diabéticos

The chronic state of hyperglycemia due to diabetes mellitus affects multiples organs impairing life quality. In bone, diabetes alters strength and mineral density and also suppresses the osteoblast activity, leading to an unbalanced bone healing process. Hyperbaric oxygen therapy (HBO) is suggested as an adjuvant treatment to accelerate bone repair. This study evaluated the effects of HBO in the number of mast cells and in new bone formation at the initial stage of bone repair in normoglycemic and diabetic rats. It was hypothesized that HBO treatment may improve bone repair in diabetic bone. The rats were equally divided in four groups: Control (C); Control + HBO (CH); Diabetes (D) and Diabetes + HBO (DH). Diabetes was induced by streptozotocin (65mg/kg) and femoral bone defects were created thirty days after diabetes induction in all groups. HBO initiated immediately after surgery procedure and was performed daily, for 7 days, in the CH e DH groups. Seven days after surgery, all animals were euthanized. The femur diaphyses were removed, fixated, decalcified and processed for paraffin embedding. The semi-serial histological sections obtained were stained with Hematoxylin-Eosin (HE), Mallory Trichrome and Toluidine Blue. The qualitative analysis was conducted in the histology slides stained with HE, where it was evaluated the morphological aspects of bone repair in the lesion area, observing the presence of clot, inflammatory cells, granulation tissue, type of bone tissue, morphology of bone cells, and thickness and organization of bone trabeculae. In the slides stained with Mallory Trichrome and Toluidine Blue were evaluated the percentage of new bone formation and number of mast cells, respectively. The qualitative analysis showed that the CH group presented a more advanced stage of bone repair compared to the C group, showing thicker trabeculae and greater bone filling of the lesion area. In D and DH group, the lesion area was partially filled with new bone formation tissue and presented thinner trabeculae and fewer areas associated to osteoclasts compared to control group. The histomorphometric analysis showed a significant improvement in new bone formation (p<0.001) comparing CH (38.08 ± 4.05) and C (32.05 ± 5.51); C and D (24.62 ± 2.28 and CH and DH (27.14 ± 4.21) groups. In the normoglycemic rats there was a significant increasing in the number of mast cells (p<0.05) comparing C (8.06 ± 5.15) and CH (21.06 ± 4.91) groups. In conclusion, this study showed that diabetes impaired bone repair and HBO was only able to increase new bone formation and the number of mast cells in the normoglycemic animals.

Avaliação das condições de precipitação do azul da Prússia sobre pó de grafite visando o desenvolvimento de eletrodos de pasta de carbono para a quantificação de nitrito

An amperometric FIA method for nitrite quantification based on nitrite electroreduction and employing a carbon paste electrode (CPE) chemically modified with iron hexacyanoferrate (HCF) as an amperometric detector was developed. The influence of experimental conditions on the preparation of the electrode materials was evaluated and the materials obtained in each study were used for the development of modified electrodes. The electrochemical sensors were prepared by a fast, simple, and inexpensive procedure, and the long-term performance of the electrodes were quite satisfactory as the stability was maintained over one year. HCF was an effective redox mediator for nitrite electroreduction in acidic media, allowing nitrite detection at +0.2 V vs. Ag/AgClsat, which is a potential free of possible interfering species that are normally present in food and water samples. The electrochemical cell used in the FIA system was similar to a batch injection analysis cell, enabling recirculation of the carrier solution. This is an attractive feature because it allows the use of a high flow rate (6 mL min-1) leading to high sensitivity and analysis speed, while keeping reagent consumption low. The proposed method had a detection limit of 9 μmol L-1 and was successfully employed for nitrite quantification in spiked water and sausage samples. The obtained results were in good agreement with those provided by the spectrophotometric official method. At a 95 % confidence level it was not observed statistical differences neither in nitrite content nor in the precision provided by both methods. The experimental conditions for the synthesis of HCF were optimized and the best electrode material was prepared by mixing FeCl3, K4[Fe(CN)6] and carbon powder subjected to an acid and thermal treatment (400 ºC), followed by ultrasonic agitation at 4 °C. This material was used to construct an electrode with improved analytical performance to reduce nitrite, which presented greater stability compared to HCF film electrodeposited on the EPC, showing that the preparation procedure of the electrode material is an effective strategy for the development of HCF modified electrodes.

Caracterização e avaliação da atividade fotocatalítica de catalisadores baseados no TiO2, sintetizados mediante hidrólise em uma mistura de solventes

This study involved the synthesis of photocatalysts based on titanium dioxide (TiO2). The photocatalysts were synthesized by the sol-gel method using three different proportions of acetone (25%, 50% and 75% v/v) in water/acetone mixtures, in order to control the hydrolysis of the precursor of titanium (titanium tetraisopropoxide). Aiming to investigate the structural, morphological and electronic changes provoked by the use of the solvent mixtures, different methodologies were used to characterize the oxides, such as X-ray diffraction (XRD), RAMAN spectroscopy, UV-Vis diffuse reflectance spectroscopy, and measurements of specific surface area (BET). XRD combined to RAMAN analyses revealed that the products are two-phase highly crystalline oxides involving anatase as main phase and brookite. Besides, the refined XRD using the method of Rietveld demonstrated that the presence of acetone during the synthesis influenced in the composition of the crystalline phases, increasing the proportion of the brookite phase between 13 and 22%. The band gap energy of these oxides practically did not suffer changes as function of the synthesis conditions. As shown by the isotherm, these photocatalysts are mesoporous materials with mean diameter of pores of 7 nm and approximately 20% of porosity. The surface area of the oxides prepared by hydrolysis in presence of acetone was 12% higher compared to the bare oxide. After characterized, these oxides had their photocatalytic activities evaluated by photodegradation of the azo dyes Ponceau 4R (P4R), Tartrazine (TTZ) and Reactive Red 120 (RR120), and also by the ability to mediate the photocatalytic production of hydrogen. Using the most efficient photocatalyst, the mineralization achieved for the dyes P4R, RR120 and TTZ was of respectively 83%, 79% and 56% in 120 minutes of reaction, while the discoloration of P4R e RR120 reached 100% and 94% for TTZ. In addition, the same photocatalyst in the presence of 0.5% w/w of Platinum and suspended in a 5:1 v/v water/methanol mixture, produced 56 mmol of gaseous hydrogen in five hours of experiment, corresponding to a specific rate of hydrogen production of 139.5 mmol h-1 g-1.

Aditivo polimérico derivado de fonte renovável para aplicação em cimento asfáltico de petróleo

This study evaluated the effects of incorporating an additive from an agro-industrial residue, after some chemical modification reactions, to petroleum asphalt cement (CAP) through the polymerization reaction of a viscous polyol obtained by bagasse biomass oxypropylation reaction sugarcane with anhydrides. The polyol is obtained by biomass oxypropylation reaction with propylene oxide, the reaction was performed in an autoclave sealed with pressure and temperature control using 25 mL of OP for every 5 grams of biomass 200°C, which time reaction was two hours. The reaction is revealed by varying the system pressure, initially at atmospheric pressure to reach a maximum pressure value and its subsequent return to atmospheric pressure. For the choice of the most suitable reaction time for polymerization of the polyol with pyromellitic anhydride, the reaction was also conducted in an autoclave sealed with temperature controller (150 ° C) using 20 g of polyol, 1 g of sodium acetate (catalyst) and 8 g of pyromellitic anhydride with the times 30 and 60 minutes. The polymerized materials with different times were characterized by determining the relative viscosity and percentage content of extractable in cyclohexane / ethanol. Given the results with the polymerized material 30 minutes showed the lowest percentage content of extractives and an increased viscosity relative indicating that this time is highlighted with respect to time 60 minutes, because the material is possibly in the form of a crosslinked polymer. Given the choice of time of 30 minutes other polymerization reactions were performed with various anhydrides and other conditions employed different proportions by mass of polyol anhydrides we were referred to as condition I (20 g anhydride and 8 g of polyol), II (20 g anhydride and 20 g of polyol) and III (8 g anhydride and 20 g of polyol). The FTIR spectra of polymeric materials with different polymerization conditions used to prove the occurrence of chemical modification due to the appearance of a characteristic band ester groups (1750 cm-1) present in the polymerized material. He chose to work with the condition III, as is the condition which employs a larger amount of polyol, and even with the smaller amount of anhydride used FTIR spectra revealed that the polymerization reaction was performed. Among the various anhydrides (phthalic, maleic and pyromellitic) of the different conditions used that stood out before the solubility test with solvents analyzed was polymerized material with pyromellitic anhydride because the polymerized material likely in the form of a crosslinked polymer because it was insoluble or poorly soluble in the solvents tested. Polymerization of the polyol with pyromellitic anhydride using condition III, that is, BCPP30, CSPP30, PCPP30 e BCPPG30, provided an increase in thermal stability relative to material in the form of polyol. Applicability tests concerning the incorporation of 16% m / m BCPP30, CSPP30, PCPP30 e BCPPG30 additive in relation to the mass of 600 g CAP showed through characterization tests used, softening point, elastic recovery and marshall dosage, it is possible to use BCPP30 as an additive the conventional CAP, because even with the incorporation of this new additive modified CAP met the specifications of the appropriate standard.

Efeito da geometria do implante dentário e do protocolo de fresagem óssea na estabilidade primária e na osseointegração inicial: estudo experimental em cães

CHAPTER 1 - This study histologically evaluated two implant designs: a classic thread design versus another specifically designed for healing chamber formation placed with two drilling protocols. Forty dental implants (4.1 mm diameter) with two different macrogeometries were inserted in the tibia of 10 Beagle dogs, and maximum insertion torque was recorded. Drilling techniques were: until 3.75 mm (regular-group); and until 4.0 mm diameter (overdrillinggroup) for both implant designs. At 2 and 4 weeks, samples were retrieved and processed for histomorphometric analysis. For torque and BIC (bone-to-implant contact) and BAFO (bone area fraction occupied), a general-linear model was employed including instrumentation technique and time in vivo as independent. The insertion torque recorded for each implant design and drilling group significantly decreased as a function of increasing drilling diameter for both implant designs (p<0.001). No significant differences were detected between implant designs for each drilling technique (p>0.18). A significant increase in BIC was observed from 2 to 4 weeks for both implants placed with the overdrilling technique (p<0.03) only, but not for those placed in the 3.75 mm drilling sites (p>0.32). Despite the differences between implant designs and drilling technique an intramembranous-like healing mode with newly formed woven bone prevailed. CHAPTER 2 - The objective of this preliminary histologic study was to determine whether the alteration of drilling protocols (oversized, intermediate, undersized drilling) present different biologic responses at early healing periods of 2 weeks in vivo in a beagle dog model. Ten beagle dogs were acquired and subjected to surgeries in the tibia 2 weeks before euthanasia. During surgery, 3 implants, 4 mm in diameter by 10 mm in length, were placed in bone sites drilled to 3.5 mm, 3.75 mm, and 4.0 mm in final diameter. The insertion and removal torque was recorded for all samples. Statistical significance was set to 95% level of confidence and the number of dogs was considered as the statistical unit for all comparisons. For the torque and BIC and BAFO, a general linear model was employed including instrumentation technique and time in vivo as independent. Overall, the insertion torque increased as a function of drilling diameter from 4.0 mm, to 3.75 mm, to 3.5 mm, with a significant difference in torque levels between all groups (p<0.001). Statistical assessment of BIC and BAFO showed significantly higher values for the 3.75 mm (recommended) drilling group was observed relative to the other two groups (p<0.001). Different drilling dimensions resulted in variations in insertion torque values (primary stability) and different pattern of healing and interfacial remodeling was observed for the different groups. CHAPTER 3 - The present study evaluated the effect of different drilling dimensions (undersized, regular, and oversized) in the insertion and removal torques of dental implants in a beagle dog model. Six beagle dogs were acquired and subjected to bilateral surgeries in the radii 1 and 3 weeks before euthanasia. During surgery, 3 implants, 4 mm in diameter by 10 mm in length, were placed in bone sites drilled to 3.2 mm, 3.5 mm, and 3.8 mm in final diameter. The insertion and removal torque was recorded for all samples. Statistical analysis was performed by paired t tests for repeated measures and by t tests assuming unequal variances (all at the 95% level of significance). Overall, the insertion torque and removal torque levels obtained were inversely proportional to the drilling dimension, with a significant difference detected between the 3.2 mm and 3.5 mm relative to the 3.8 mm groups (P < 0.03). Although insertion torque–removal torque paired observations was statis- tically maintained for the 3.5 mm and 3.8 mm groups, a significant decrease in removal torque values relative to insertion torque levels was observed for the 3.2 mm group. A different pattern of healing and interfacial remodeling was observed for the different groups. Different drilling dimensions resulted in variations in insertion torque values (primary stability) and stability maintenance over the first weeks of bone healing.

Influência da utilização do fluido de corte com adição de grafeno na temperatura de usinagem e formação de rebarba no processo de micro fresamento

As time passed, humanity needed the development of new materials used in various activities. High strength materials such as titanium and Inconel for example, had been studied because they are widely used for implants in biomedicine, as well as their use in aerospace and automotive industries. Because of its thermal and mechanical properties, these materials are considered difficult to machine, promoting a rapid wear of cutting tools, primarily caused by the high temperatures in machining. With the development of new materials has emerged the need of developing new manufacturing processes. One of today’s innovative processes is the micro-manufacturing. Being a process with a defined cutting tool geometry, burr formation is a constant and undesirable phenomenon formed during the machininig process. Being detrimental to the manufacturing process, overspending deburring operations are constantly employed leading to increase the aggregate cost to the manufactured material. Assembly components are also impaired if there is no control of the burr, with consequences including the disposal of components due to the occurence of this phenomenon. This paper presents the study of micro-milling Inconel 718, investigating influential parameters in the formation of burrs in order to minimize the occurrence of this phenome non. Different feed rates per tooth and cutting speed are evaluated, and different cutting fluids with different methods of applying the fluid. Adding graphene to cutting fluids was considered as a variable to be investigated, which is considered an excellent solid lubricant, in addition to increasing the thermal conductivity of the cooling solution (AZIMI; MOZAF FARI, 2015). The micro-milling temperature was evaluated in the present work. It was observed a new phenomenon that causes the machined surface temperature decreases below room temperature when using the solution water + oil. This phenomenon is explained in further chapters. In order to unravel this phenomenon, a new test was proposed and, from this test, it can be concluded, comparatively, which cutting fluid has a better cooling property.Using cutting fluid with different thermal properties has shown influence when analy zing burr formation and reducing machining temperature.

Retificação plana tangencial dos ferros fundidos nodular, vermicular e cinzento em várias condições de corte

In a scenario of increasing competitiveness of the global industrial sector and with a consumer market increasingly demanding, there is an increased demand for new materials and, consequently, possibilities to explore new research and technological advances towards the development of new manufacturing methods or the improvement of existing technologies. In the case of cast irons, new grades of them have been developed so that their mechanical properties have been improved, making them more competitive with steel, expanding the applications and thus represents great economic gain for metallurgy and manufacturing sectors. This increases the interest and creates new opportunities to study these materials and identify how they respond in terms of the surface integrity, tool wear, cutting forces, among others, when machined by grinding operation. In this context, due to the lack of results from grinding of cast irons and studies comparing grindability among several grades of cast irons found in the literature, this work aims to generate scientific and technological contribution to the metallurgical and metal working sector through roughness results (Ra and Rz parameters) and evaluation and analysis of the subsurface integrity of three cast iron grades (gray, compacted graphite and nodular). The machining trials were performed on a surface grinding machine with silicon carbide grinding wheel at different cutting conditions. The input variables were the radial depth of cut (15 and 30 μm), worktable speed, vw (5 and 10 m/min) and the abrasive grain size of the grinding wheel. The results showed that surface roughness increased with the radial depth of cut for all materials tested; and the lowest values were obtained for gray cast iron. Also, roughness was sensitive to variation of worktable speed and the lowest values were obtained after machining with vw = 5 m/min. With respect to the abrasive grain size, as it decreased the roughness values increased to gray and nodular cast iron grades. Furthermore, grinding burns marks were observed on the surfaces of nodular cast iron and compacted graphite iron grades after grinding the smallest grain size, contrary to what is usually reported in literature. However, no evidence of severe thermal damages below the machined surfaces of all cast iron grades was observed after analyzing the results of hardness and the SEM micrograph images.

Perfil sorológico contra Rickettsia spp e Leptospira spp e infestação de carrapatos em suínos mantidos sob diferentes sistemas de criação

The various types of pig farming, intensive and extensive, expose them to pig parasites but also to those from the environment of the breeding site. In this work was evaluated the exposure of bigs bred in technified farms, SISCAL (intensive breeding system in pens) and not technified (backyard) to leptospira, ticks and rickettsiae. Blood sera were analyzed to determine titers of antibodies anti-Leptospira by SAM technique and antibodies anti-rickettsial by IFA, pigs were inspected for ticks and in their breeding environment and surrounding areas (pastures and riparian vegetation), ticks were collected by the flannel dragging technique. In the farms of pigs 10.4% had anti-Leptospira antibodies, followed by SISCAL (8%) and backyard animals (2.5%). The serovars found were Bratislava, Pomona, serovar, Canicola and Icterohaemorrhagiae. Higher percentage of properties with pigs raised outdoors (SISCAL) had tick infested animals (20%) than those raised in backyard (6.7%), while commercial farms had no infested pigs nor infested breeding place. In both SISCAL and backyard pig breeding properties ticks were observed at the breeding site environment. Tick infestations were detected in areas surrounding pig breeding site in all three husbandry suystems. Ticks found were all Amblyomma scultpum nymphs or adults with the exception of one of Amblyomma parvum adult. In relation to anti-rickettsia serology to five Rickettsia species, 55.2% of pigs from commercial farms reacted to al least one species, backyard pigs reacted to 89.7% and all pigs of SISCAL showed anti-rickettsia titers. Consecutive tick sampling (June 2014 to February 2016) in SISCAL FAZU in Uberaba, showed the establishment A. sculptum ticks maintained by domestic pigs. These observations demonstrate the ability the pigs to maintain populations of A. sculptum at a favorable environment and may indicate a new trend in environmental infestations by this species of tick. Exposure to Leptospira and Rickettsia demonstrated the potential pigs exposure and transmission of important diseases in public health.

Métodos de extração de fósforo e micronutrientes em latossolos com uso de energia ultrassônica

Assessing the soil nutrient availability to plants under lab conditions is one of the main challenges to Soil Fertility and Chemistry, due to the complex behavior and the interaction of the soil properties. Many extractant solutions associated with mechanical forms of agitation have been proposed, showing different correlations with plant growth and nutrients absorption. Using ultrasonic energy is a agitation procedure of the soil:extractant solution suspension (based on the cavitation phenomenon). It allows the establishment of relations between the amount of extracted nutrient and the ultrasonic energy level. Thus, this work aims: to evaluate the effect of cavitation intensity on the extraction of P, Zn, Cu, Mn and Fe in soil samples from five Latosols under different uses around Uberlândia and Uberaba, Minas Gerais State; to obtain extracting curves as function of ultrasonic energy levels; and to obtain an index from extracting curves to expresses the nutrient retention by the soil solid phase. A soil-solution suspension (ratio 1:10) was sonicated using a probe ultrasound equipment under different combinations of power and time: i) 30 W for 35, 70, 140 and 280 s; ii) 50 W for 21, 42, 84 and 168 s; and iii) 70 W for 15, 30, 60 and 120 s. The extractant solutions used were Mehlich-1 (for all elements), Olsen and distilled water for P. After each sonication, P concentration was quantified by molybdenum blue colorimetric method and Zn, Cu, Mn and Fe by flame atomic absorption spectrophotometry. The cavitation intensity did not affect the P extraction, only the total energy applied. The P extraction was influenced by extractant solution, decreasing as follows: Mehlich-1>Olsen>water. In cultivated Latosols, the P extraction increased linearly with ultrasonic energy, and the slope of the 1:1 linear regression reflects the P retention in the soil. The Zn and Fe extractions were influenced only by total energy applied. Mn and Cu extractions were influenced by both cavitation intensity and total ultrasonic energy. Soils containing similar amounts of P, Cu, Zn, Mn, and Fe may have a different extraction rate. Likewise, soils containing different amounts of those elements may have the same extraction rate.

Características de virulência, resistência e diversidade genética de sorovares de Salmonella com impacto na saúde pública, isolados de frangos de corte no Brasil /

Salmonella Enteritidis, S. Typhimurium and S. Infantis are often associated with cases of human infections worldwide and is transmitted through consumption of contaminated food, particularly those of animal origin, especially chicken meat. This thesis was fractionated into three chapters, the first one relating to general considerations about the topics discussed in the following chapters. The second chapter aimed to evaluate virulence characteristics, antimicrobial resistance and the genetic similarity of 51 strains of S. Infantis isolated in samples of poultry origin from an industry located in the state of São Paulo, Brazil, during the 2009 to 2010 period. The third chapter aimed to analyze 111 strains of S. Enteritidis, 45 of Salmonella Typhimurium and 31 of Salmonella Typhimurium monophasic variant I 4, [5], 12:i:- isolated from chicken carcasses in different brazilian slaughterhouses from 2009 to 2011, and to estimate the risk to human health, based on the presence of virulence genes and antimicrobial resistance, correlating to the pathogenicity profiles (antimicrobial resistance and presence of virulence and resistance genes) with the genetic profile (ribogroup) of the isolates. To evaluate the antimicrobial susceptibility was performed the disk diffusion test for all serotypes of Salmonella, and exclusively to S. Enteritidis and S. Typhimurium, was also verified the minimum inhibitory concentration for ciprofloxacin and ceftazidime antibiotics. The presence of virulence genes invA (invasion), lpfA (fimbriae-adhesion), agfA (fimbriae-biofilm) and sefA (fimbriae-adhesion) were evaluated by PCR. The strains that showed resistance to antibiotics of β-lactams class were evaluated for the presence of resistance genes blaTEM, blaSHV, blaCTX-M and blaAmpC. For resistant strains to quinolones and fluoroquinolones antibiotics classes were searched the qnrA and qnrS genes. The phylogenetic relationship among the isolates was determined by RAPD method for S. Infantis strains, and by ribotyping technique to S. Enteritidis and S. Typhimurium.