Determinação voltamétrica de zinco empregando eletrodos quimicamente modificados com bismuto

This dissertation presents the development of voltammetric methods to zinc determination in multivitamin commercial samples, talc, and art materials for painting (soft pastel) combining an alkaline extraction with 1.0 mol L-1 NaOH aqueous solution and bismuth modified electrodes. Two electrodes were used to zinc quantification in the samples, bismuth film electrode (BiFE) plated in situ onto glassy carbon and carbon paste electrode chemically modified with strongly acidic ion exchange resin Amberlite® IR 120 and bismuth nanostructures (EPCAmbBi). It was verified that the best concentration of Bi3+ for Bi film deposition onto glassy carbon was 4.0 μmol L-1 using an 0.1 mol L-1 acetate buffer aqueous solution (pH = 4.5) as supporting electrolyte. The best condition to formation of Bi nanostructures in the EPC modified with 10 % Amberlite® IR 120 was the use of 30 s to pre-concentration (open circuit) in 0.5 mmol L-1 Bi3+ aqueous solution (pH 5.5) prepared with supporting electrolyte solution. The obtained analytical curve for Zn2+ using BiFE presented linear range from 0.5 to 5.0 μmol L-1, the limit of detection (LD) was 41 nmol L-1. For EPCAmbBi only one linear range was observed for the analytical curve varying the Zn2+ concentration from 0.05 to 8.2 μmol L-1, LD obtained in this curve it was equal to 10 nmol L-1. The EPCAmbBi presented the most intense and sharp anodic stripping peaks for Zn2+ presenting, therefore, a better voltammetric profile, with sensitivity higher than obtained with the BiFE. Moreover, the EPCAmbBi presented a LD lower than that obtained with the BiFE. Alkaline extraction was an efficient sample pretreatment to extract Zn2+ from solid samples, besides that, this procedure was less susceptible to interferences from Cu2+, since it remains at extracting vessel as insoluble Cu(OH)2. The combination of alkaline extraction with the EPCAmbBi is a simple, fast, efficient and low cost for the zinc determination in pharmaceutical formulations and art materials for painting (soft pastel) samples, which can be employed as a low-cost alternative method to the atomic absorption spectroscopy.

Determinação do estado fundamental de compostos antiferromagnéticos da série Tb(1-x)Y(x)RhIn(5): aproximação teórico experimental

We present the results of electrical resistivity, magnetic susceptibility, specific heat and x-ray absorption spectroscopy measurements in Tb1−xYxRhIn5 (x = 0.00, 0.15, 0.4.0, 0.50 e 0.70) single crystals. Tb1−xYxRhIn5 is an antiferromagnetic AFM compound with ordering temperature TN ≈ 46 K, the higher TN within the RRhIn5 serie (R : rare earth). We evaluate the physical properties evolution and the supression of the AFM state considering doping and Crystalline Electric Field (CEF) effects on magnetic exchange interaction between Tb3+ magnetic ions. CEF acts like a perturbation potential, breaking the (2J + 1) multiplet s degeneracy. Also, we studied linear-polarization-dependent soft x-ray absorption at Tb M4 and M5 edges to validate X-ray Absorption Spectroscopy as a complementary technique in determining the rare earth CEF ground state. Samples were grown by the indium excess flux and the experimental data (magnetic susceptibility and specific heat) were adjusted with a mean field model that takes account magnetic exchange interaction between first neighbors and CEF effects. XAS experiments were carried on Total Electron Yield mode at Laborat´onio Nacional de Luz S´ıncrotron, Campinas. We measured X-ray absorption at Tb M4,5 edges with incident polarized X-ray beam parallel and perpendicular to c-axis (E || c e E ⊥ c). The mean field model simulates the mean behavior of the whole system and, due to many independent parameters, gives a non unique CEF scheme. XAS is site- and elemental- specific technique and gained the scientific community s attention as complementary technique in determining CEF ground state in rare earth based compounds. In this work we wil discuss the non conclusive results of XAS technique in TbRhIn5 compounds.

Métodos de extração de fósforo e micronutrientes em latossolos com uso de energia ultrassônica

Assessing the soil nutrient availability to plants under lab conditions is one of the main challenges to Soil Fertility and Chemistry, due to the complex behavior and the interaction of the soil properties. Many extractant solutions associated with mechanical forms of agitation have been proposed, showing different correlations with plant growth and nutrients absorption. Using ultrasonic energy is a agitation procedure of the soil:extractant solution suspension (based on the cavitation phenomenon). It allows the establishment of relations between the amount of extracted nutrient and the ultrasonic energy level. Thus, this work aims: to evaluate the effect of cavitation intensity on the extraction of P, Zn, Cu, Mn and Fe in soil samples from five Latosols under different uses around Uberlândia and Uberaba, Minas Gerais State; to obtain extracting curves as function of ultrasonic energy levels; and to obtain an index from extracting curves to expresses the nutrient retention by the soil solid phase. A soil-solution suspension (ratio 1:10) was sonicated using a probe ultrasound equipment under different combinations of power and time: i) 30 W for 35, 70, 140 and 280 s; ii) 50 W for 21, 42, 84 and 168 s; and iii) 70 W for 15, 30, 60 and 120 s. The extractant solutions used were Mehlich-1 (for all elements), Olsen and distilled water for P. After each sonication, P concentration was quantified by molybdenum blue colorimetric method and Zn, Cu, Mn and Fe by flame atomic absorption spectrophotometry. The cavitation intensity did not affect the P extraction, only the total energy applied. The P extraction was influenced by extractant solution, decreasing as follows: Mehlich-1>Olsen>water. In cultivated Latosols, the P extraction increased linearly with ultrasonic energy, and the slope of the 1:1 linear regression reflects the P retention in the soil. The Zn and Fe extractions were influenced only by total energy applied. Mn and Cu extractions were influenced by both cavitation intensity and total ultrasonic energy. Soils containing similar amounts of P, Cu, Zn, Mn, and Fe may have a different extraction rate. Likewise, soils containing different amounts of those elements may have the same extraction rate.

Investigação da rota biohidrometalúrgica com Acidithiobacillus ferrooxidans/thiooxidans para recuperação do cobalto de baterias de íons lítio descartadas

The recycling of metals from secondary sources can be advantageous. Among the metals of interest, we have cobalt, a metal used for various purposes. As regards the secondary sources of cobalt, the lithium-ion batteries can be considered, since they contain cobalt oxide in their composition (LiCoO2). This way, the objective of this work was to use the microorganism strains (Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans) to bioleach the LiCoO2 extracted from discarded lithium ion batteries with emphasis on the recovery of cobalt for synthesis of new materials of interest. The lineage growth occurred in T&K medium and the growth investigation was made by observing the media, by platelet growth and microscope analysis. Then, the inoculum was standardized on 5 x 106 cells mL-1 and used in bioleaching tests. The bioleaching was investigated: the microorganism nature: separate strains and A. ferrooxidans and A. thiooxidans consortium, bioleaching time (0 to 40 days), inoculum proportion (5 to 50% v/v), energy source (iron and sulfur) and residue concentration (1063 to 8500 mg L-1 of cobalt). The cobalt concentration in the media was found by atomic absorption spectrometry and the medium pH was monitored during the bioleaching. The results show that the amount of bioleached cobalt increases with time and the iron concentration. The bioleaching with A. thiooxidans was not influenced by the addition of sulfur. The use of the two lineages together did not improve the bioleaching rates. Among the lineages, the A. thiooxidans presented better results and was able to bioleach cobalt amounts above 50% in most of the experiments. A. thiooxidans presented lower bioleaching rates, with a maximum of 50% after 24 days of experiment. After reprocessing by bioleaching, the cobalt in solution was used for synthesis of new materials: such as LiCoO2 cathode and as adsorbent pesticide double lamellar hydroxide (HDL Co-Al-Cl) by the Pechini and co-precipitation methods. The reprocessed LiCoO2 presented a unique stoichiometric phase relative to the HT-LiCoO2 structure similar to the JCPDS 44-0145, presenting electrochemical activity when tested as a cathode material. The double lamellar hydroxide Co-Al-Cl was tested as pesticide adsorbent, being possible to adsorb around 100% of the pesticide. The bioleaching was efficient in the recovery of cobalt present in lithium-ion batteries and microorganisms presented high tolerance to the residue, being able to bioleach even at higher LiCoO2 concentrations. The cobalt bioleaching medium did not impair the synthesis phases and the obtained materials presented structure and activity similar to the sintered materials from the reagents containing cobalt.

Aplicação de espectroscopia no infravermelho médio e calibração multivariada para quantificação de adulterantes e teor em biodiesel de óleo de palma com óleo de soja, soja residual e diesel

In this work, it was developed and validated methodologies that were based on the use of Infrared Spectroscopy Mid (MIR) combined with multivariate calibration Square Partial Least (PLS) to quantify adulterants such as soybean oil and residual soybean oil in methyl and ethyl palm biodiesels in the concentration range from 0.25 to 30.00 (%), as well as to determine methyl and ethyl palm biodiesel content in their binary mixtures with diesel in the concentration range from 0.25 to 30.00 (%). The prediction results showed that PLS models constructed are satisfactory. Errors Mean Square Forecast (RMSEP) of adulteration and content determination showed values of 0.2260 (%), with mean error (EM) with values below 1.93 (%). The models also showed a strong correlation between actual and predicted values, staying above 0.99974. No systematic errors were observed, in accordance to ASTM E1655- 05. Thus the built PLS models, may be a promising alternative in the quality control of this fuel for possible adulterations or to content determination.

Determinação de teor de biodieseis de algodão e pinhão manso em misturas com diesel usando espectroscopia no infravermelho médio e quadrados mínimos parciais

Biodiesel is a renewable fuel derived from vegetable oils or animal fats, which can be a total or partial substitute for diesel. Since 2005, this fuel was introduced in the Brazilian energy matrix through Law 11.097 that determines the percentage of biodiesel added to diesel oil as well as monitoring the insertion of this fuel in market. The National Agency of Petroleum, Natural Gas and Biofuels (ANP) establish the obligation of adding 7% (v/v) of biodiesel to diesel commercialized in the country, making crucial the analytical control of this content. Therefore, in this study were developed and validated methodologies based on the use of Mid Infrared Spectroscopy (MIR) and Multivariate Calibration by Partial Least Squares (PLS) to quantify the methyl and ethyl biodiesels content of cotton and jatropha in binary blends with diesel at concentration range from 1.00 to 30.00% (v/v), since this is the range specified in standard ABNT NBR 15568. The biodiesels were produced from two routes, using ethanol or methanol, and evaluated according to the parameters: oxidative stability, water content, kinematic viscosity and density, presenting results according to ANP Resolution No. 45/2014. The built PLS models were validated on the basis of ASTM E1655-05 for Infrared Spectroscopy and Multivariate Calibration and ABNT NBR 15568, with satisfactory results due to RMSEP (Root Mean Square Error of Prediction) values below 0.08% (<0.1%), correlation coefficients (R) above 0.9997 and the absence of systematic error (bias). Therefore, the methodologies developed can be a promising alternative in the quality control of this fuel.