Projeto iterativo, simulação, análise e otimização de máquina a relutância variável monofásica

Variable reluctance motors have been increasingly used as an alternative for variable speed and high speed drives in many industrial applications, due to many advantages like the simplicity of construction, robustness, and low cost. The most common applications in recent years are related to aeronautics, electric and hybrid vehicles and wind power generation. This paper explores the theory, operation, design procedures and analysis of a variable reluctance machine. An iterative design methodology is introduced and used to design a 1.25 kW prototype. For the analysis of the machine two methods are used, an analytical method and the finite element simulation. The results obtained by both methods are compared. The results of finite element simulation are used to determine the inductance profiles and torque of the prototype. The magnetic saturation is examined visually and numerically in four critical points of the machine. The data collected in the simulation allow the verification of design and operating limits for the prototype. Moreover, the behavior of the output quantities is analyzed (inductance, torque and magnetic saturation) by variation of physical dimensions of the motor. Finally, a multiobjective optimization using Differential Evolution algorithms and Genetic Algorithms for switched reluctance machine design is proposed. The optimized variables are rotor and stator polar arcs, and the goals are to maximize the average torque, the average torque per copper losses and the average torque per core volume. Finally, the initial design and optimized design are compared.

Influência da utilização do fluido de corte com adição de grafeno na temperatura de usinagem e formação de rebarba no processo de micro fresamento

As time passed, humanity needed the development of new materials used in various activities. High strength materials such as titanium and Inconel for example, had been studied because they are widely used for implants in biomedicine, as well as their use in aerospace and automotive industries. Because of its thermal and mechanical properties, these materials are considered difficult to machine, promoting a rapid wear of cutting tools, primarily caused by the high temperatures in machining. With the development of new materials has emerged the need of developing new manufacturing processes. One of today’s innovative processes is the micro-manufacturing. Being a process with a defined cutting tool geometry, burr formation is a constant and undesirable phenomenon formed during the machininig process. Being detrimental to the manufacturing process, overspending deburring operations are constantly employed leading to increase the aggregate cost to the manufactured material. Assembly components are also impaired if there is no control of the burr, with consequences including the disposal of components due to the occurence of this phenomenon. This paper presents the study of micro-milling Inconel 718, investigating influential parameters in the formation of burrs in order to minimize the occurrence of this phenome non. Different feed rates per tooth and cutting speed are evaluated, and different cutting fluids with different methods of applying the fluid. Adding graphene to cutting fluids was considered as a variable to be investigated, which is considered an excellent solid lubricant, in addition to increasing the thermal conductivity of the cooling solution (AZIMI; MOZAF FARI, 2015). The micro-milling temperature was evaluated in the present work. It was observed a new phenomenon that causes the machined surface temperature decreases below room temperature when using the solution water + oil. This phenomenon is explained in further chapters. In order to unravel this phenomenon, a new test was proposed and, from this test, it can be concluded, comparatively, which cutting fluid has a better cooling property.Using cutting fluid with different thermal properties has shown influence when analy zing burr formation and reducing machining temperature.

Desenvolvimento do capim-marandu com altura fixa ou variável durante as estações do ano

Aimed to identify, for assessing the tillering dynamics and morphogenesis , strategy (s ) suitable ( s) defoliation management to optimize the appearance of tillers and biomass of Urochloa Brizantha syn. Brachiaria brizantha cv. Marandu ( marandugrass ) throughout the year. The experiment was conducted from January 2013 to May 2014 were studied three strategies defoliation: Marandugrass with 30 cm throughout the experimental period (constant height); Marandugrass 15 cm in winter, the spring 30 cm and 45 cm in summer (increasing height); and Marandugrass 45 cm in winter, the spring 30 cm and 15 cm in summer (descending height). The experimental design was completely randomized in a split plot in time, with four replications. In winter, in the spring and summer, the following variables were calculated: appearance rate (TApP), mortality (TMoP) and survival (TSoP) of tillers, balance (BAL) between TApP and TMoP, stability index (IE) numbers of tillers and leaf elongation rates and stem, length of leaf blade and stem, leaf senescence rate, phyllochron and duration of life of the sheet. The TAPP was higher in the early spring and summer. For TMoP, the highest values were in the late spring and summer. The balance between TApP and TMoP was negative in winter and late spring, regardless of defoliation strategy. There was no difference in IE between the heights of the canopy during winter and late spring .. The number of tillers was higher in early spring and summer and lower in winter and late spring. The defoliation strategies have not changed phyllochron, leaf elongation rate. In spring and summer, there were increases in the rates of appearance, elongation and leaf senescence and, furthermore, decreased life span and phyllochron sheet. The plant height with increasing showed a lower rate of senescence and lower culm length in the spring. To increase the number of tillers marandu, it is advantageous to handle the plant with increasing height, ie, 15 cm in autumn and winter, the spring 30 cm and 45 cm in summer.The maintaining of B. brizantha cv. Marandu with fixed height of 30 cm or with variations between 15 and 45cm from the fall/winter to summer, does not influence the appearance and the growth of leaves per tiller, which indicates great flexibility on management defoliation in this forage plant.

Efeito da concentração de sólidos e de variáveis operacionais no desempenho de um hidrociclone concentrador

The hydrocycloning operation has a goal to separate solid-liquid suspensions and liquid-liquid emulsions through the centrifugal force action. Hydrocyclones are equipment with reduced size and used in both clarification and thickening. This device is used in many areas, like petrochemical and minerals process, and accumulate advantages like versatility and low cost of maintenance. However, the demand to improve the process and to reduce the costs has motivated several studies of equipment optimization. The filtering hydrocyclone is a non-conventional equipment developed at FEQUI/UFU with objective to improve the hydrocycloning separation efficiency. The purpose of this study is to evaluate the operating conditions of feed concentration and underflow diameter on the performance of a filtering geometry optimized to minimization of energy costs. The filtration effect was investigated through the comparison between the performance of the Optimized Filtering Hydrocyclone (HCOF) and the Optimized Concentrator Hydrocyclone (HCO). Because of the resemblance of hydrocyclones performance, the filtration did not represent significant effect on the performance of the HCOF. It was found that in this geometry the decrease of the variable underflow diameter was very favorable to thickening operation. The suspension concentration of quartzite at 1.0% of solids in volume was increased about 42 times when the 3 mm underflow diameter was used. The increase on the feed solid percentage was good for decreasing the energy spent, so that a minimum number of Euler of 730 was achieved at CVA = 10.0%v. However, a greater amount of solids in suspension leads to a lower efficiency of the equipment. Therefore, to minimize the underflow-to-throughput ratio and keep a high efficiency level, it is indicated to work with dilute suspension (CVA = 1.0%) and 3 mm underflow diameter (η = 67%). But if it is necessary to work with high feed concentration, the use of 5 mm underflow diameter provides a rise in the efficiency. The HCO hydrocyclone was compared to the traditional family of hydrocyclones Rietema and presented advantages like higher efficiency (34% higher in average) and lower energy costs (20% lower in average). Finally, the efficiency curves and project equation have been raised for the HCO hydrocyclone each with satisfactory adjust.