Efeito da concentração de sólidos e de variáveis operacionais no desempenho de um hidrociclone concentrador

The hydrocycloning operation has a goal to separate solid-liquid suspensions and liquid-liquid emulsions through the centrifugal force action. Hydrocyclones are equipment with reduced size and used in both clarification and thickening. This device is used in many areas, like petrochemical and minerals process, and accumulate advantages like versatility and low cost of maintenance. However, the demand to improve the process and to reduce the costs has motivated several studies of equipment optimization. The filtering hydrocyclone is a non-conventional equipment developed at FEQUI/UFU with objective to improve the hydrocycloning separation efficiency. The purpose of this study is to evaluate the operating conditions of feed concentration and underflow diameter on the performance of a filtering geometry optimized to minimization of energy costs. The filtration effect was investigated through the comparison between the performance of the Optimized Filtering Hydrocyclone (HCOF) and the Optimized Concentrator Hydrocyclone (HCO). Because of the resemblance of hydrocyclones performance, the filtration did not represent significant effect on the performance of the HCOF. It was found that in this geometry the decrease of the variable underflow diameter was very favorable to thickening operation. The suspension concentration of quartzite at 1.0% of solids in volume was increased about 42 times when the 3 mm underflow diameter was used. The increase on the feed solid percentage was good for decreasing the energy spent, so that a minimum number of Euler of 730 was achieved at CVA = 10.0%v. However, a greater amount of solids in suspension leads to a lower efficiency of the equipment. Therefore, to minimize the underflow-to-throughput ratio and keep a high efficiency level, it is indicated to work with dilute suspension (CVA = 1.0%) and 3 mm underflow diameter (η = 67%). But if it is necessary to work with high feed concentration, the use of 5 mm underflow diameter provides a rise in the efficiency. The HCO hydrocyclone was compared to the traditional family of hydrocyclones Rietema and presented advantages like higher efficiency (34% higher in average) and lower energy costs (20% lower in average). Finally, the efficiency curves and project equation have been raised for the HCO hydrocyclone each with satisfactory adjust.

Instrumento de avaliação de processos cognitivos para a aprendizagem de subestações de energia em ambientes 2D e realidade virtual

This study describes the development of a prototype to evaluate the potential of environments based on two-dimensional modeling and virtual reality as power substations learning objects into training environments from a central operation and control of power utility Cemig. Initially, there was an identification modeling features and cognitive processes in 2D and RV, from which it was possible to create frames that serve to guide the preparation of a checklist with assigning a metric weight for measuring cognitive potential learning in the study sites. From these contents twenty-four questions were prepared and each was assigned a weight that was used in the calculation of the metric; the questions were grouped into skill sets and similar cognitive processes called categories. Were then developed two distinct environments: the first, the prototype features an interactive checklist and your individual results. And, second, a system of data management environment for the configuration and editing of the prototype, and the observation and analysis of the survey results. For prototype validation, were invited to access the virtual checklist and answer it, five professionals linked to Cemig's training area. The results confirmed the validity of this instrument application to assess the possible potential of modeling in 2D and RV as learning objects in power substations, as well as provide feedback to developers of virtual environments to improve the system.

Avaliação da soldagem GMAW mecanizada e automatizada para união de dutos utilizando fontes convencional e com controle de curto- circuito

Welding is one of the most employed process for joining steel pipes. Although, manual welding is still the most used one, mechanized version and even automatized one have increased its demand. Thus, this work deals with girth welding of API 5L X65 pipes with 8” of nominal diameter and 8.0 mm thickness, beveled with V-30º narrow gap. Torch is moved by a bug carrier (mechanized welding) and further the parameters are controlled as a function of angular position (automatized welding). Welding parameters are presented for filling the joint with two-passes (root and filling/capping passes). Parameters for the root pass were extracted from previous author´s work with weldments carried out in plates, but validated in this work for pipe welding. GMAW processes were assessed with short-circuit metal transfer in both conventional and derivative modes using different technologies (RMD, STT and CMT). After the parameter determination, mechanical testing was performed for welding qualification (uniaxial tension, face and root bending, nick break, Charpy V-notch impact, microhardness and macrograph). The initially obtained results for RMD and CMT were acceptable for all testing and, in a second moment, also for the STT. However, weld beads carried out by using the conventional process failed and revealed the existence of lack of fusion, which required further parametrization. Thus, a Parameter-Variation System for Girth Welding (SVP) was designed and built to allow varying the welding parameters as a function of angular position by using an inclinometer. The parameters were set for each of the three angular positions (flat, vertical downhill and overhead). By using such equipment and approach, the conventional process with parameter variation allowed reducing the welding time for joint accomplishment of the order of 38% for the root pass and 30% for the filling/capping pass.

Ajustes de coeficientes integrantes de processos físicos e bioquímicos na autedepuração em curso de água de médio porte

The mathematical modeling in the simulation of self-purification capacity in lotic environment is an important tool in the planning and management of hydric resources in hydrographic basin scale. It satisfactorily deals with the self-purification process when the coefficients of physical and biochemical processes are calibrated from monitorated water quality data, which was the main focus of this study. The present study was conducted to simulate the behavior of the parameters OD, BOD5, total phosphorus, E. coli, ammonia, nitrite, nitrate and the total metals cadmium, chromium, copper, lead and zinc in the Uberabinha’s lower course (with an approximate annual growth flow between 4-35 m3/s), in a stretch of 19 km downstream of the treated effluent release by the WWTP of the city. The modelings, on the present study, show the importance of constant water quality parameters monitoration over the water course, based on the comparison of the simulations from calibrated coefficients and coefficients obtained in the literature for the period of June until November 2015. After coefficients calibration, there were good adjustments between simulated and measured data for the parameters OD, BOD, Ptotal, ammonia and nitrate and unsatisfactory adjust for the parameters nitrite and E. coli. About the total metals, the adjustments were not satisfactory on the reservoir’s vicinity of the Small Hydropower Plant Martins, due the considerable increase of the bottom sediment in lentic region. The greatest scientific contribution of this study was to calibrate the decay coefficient K and the quantification of the release by the fund S of total metals in watercourse midsize WWTP pollutant load receptor, justified by the lack of studies in the literature about the subject. For the metals cadmium, chromium, copper, lead and zinc, the borderline for K and S calibrated were: 0.0 to 13.0 day-1 and 0.0 to 1.7 g/m3.day; 0.0 to 0.9 day-1 and 0.0 to 7.3 g/m3.day; 0.0 to 25.0 day-1 and 0.0 to 1.8 g/m3.day; 0.0 to 7.0 day-1 and 0.0 to 40.3 g/m3.day; 0.0 to 30.0 day-1 and 0.0 to 70.1 g/m3.day.

Fungicidas protetores no manejo da ferrugem da soja, processos fisiológicos e produtividade da cultura

Currently, the management recommendations for asian soybean rust (ASR) has been based on the application of protective fungicides mixed with triazoles and stronilurins. Thus, this study aimed at assessing whether the increased productivity provided by the application of protective fungicides is due solely to the fungicidal action of the product or some physiological changes in the plant and which the latter would be. The experiment was conducted from March to July 2015 at the experimental station of Udi Research and Development in Uberlândia-MG, with the cultivar 97Y07 RR. The experimental design chosen for this study was comprised of a randomized block with four replications and 16 treatments: check, fluxapyroxad + pyraclostrobin (116.55 + 58.45 g ha-1), azoxystrobin + benzovindiflupir (90 + 45 g ha-1), trifloxystrobin + prothioconazole (60 + 70 g ha-1), tebuconazole + picoxystrobin (100 + 60 g ha-1), picoxystrobin + cyproconazole (60 + 24 g ha-1), mancozeb (1125 g ha-1), azoxistrobina + tebuconazole + difenoconazole (60 + 75 + 120 g ha-1), azoxystrobin + tebuconazole + difenoconazole + chlorothalonil ( 60 + 120 + 75 + 1440 g ha-1), and mistures fluxapyroxad + pyraclostrobin + mancozeb, azoxystrobin + benzovindiflupir + mancozeb, trifloxystrobin + prothioconazole + mancozeb, tebuconazole + picoxystrobin + mancozeb, picoxystrobin + cyproconazole + mancozeb, azoxystrobin + tebuconazole + difenoconazole + mancozeb, and azoxystrobin + benzovindiflupir + chlorothalonil, from the aforesaid doses. The first application of the treatments occurred in R1, in the absence of symptoms. The number of applications, intervals and the use of adjuvants were performed according to the recommendations by manufacturers. The variables analyzed were: disease severity, concentration of chlorophylls and carotenoids, photosynthetic rate (A), transpiration rate (E), stomatal conductance (gs), internal carbon concentration (Ci), instantaneous efficiency in water use (A/E), intrinsic water use efficiency (A/gs), and carboxylation efficiency (A/C). With these data collected, this study set to date the progress curve of each variable (AUPC). At the end of the crop cycle, the average of pods per plant was quantified, grain per pod, productivity and weight of 1,000 grains. It was concluded that: the addition of mancozeb to fluxapyroxad + pyraclostrobin, azoxystrobin + benzovindiflupir, trifloxystrobin + prothioconazole and tebuconazole + picoxystrobin potentiated the ASR control; adding mancozebe to the mixture azoxystrobin + benzovindiflupir provided better control of the disease compared to the addition of chlorothalonil; mancozeb amounts to AUPC concentration of photosynthetic pigments and when added to axozystrobin + tebuconazole + difenoconazole, increases the AUPC for total chlorophyll concentration, as well as when chlorothalonil was added; mancozeb added to the mix fluxapyroxad + pyraclostrobin raised the AUPC for A/Ci and A/gs, increasing the W1,000G and crop productivity; the addition of protectors similarly reflected on the productivity of culture.