An analysis of the effectiveness of a behavioural based safety intervention in a UK paper mill

This research examines a behavioural based safety (BBS) intervention within a paper mill in the South East of England. Further to this intervention two other mills are examined for the purposes of comparison — one an established BBS programme and the other an improving safety management system through management ownership. BBS programmes have become popular within the UK, but most of the research about their efficacy is carried out by the BBS providers themselves. This thesis aims to evaluate a BBS intervention from a standpoint which is not commercially biased in favour of BBS schemes. The aim of a BBS scheme is to either change personnel behaviours or attitudes, which in turn will positively affect the organisation's safety culture. The research framework involved a qualitative methodology in order to examine the effects of the intervention on the paper mill's safety culture. The techniques used were questionnaires and semi structured interviews, in addition to observation and discussions which were possible because of the author's position as participant observer. The results demonstrated a failure to improve any aspect of the mill's safety culture, which worsened following the BBS intervention. Issues such as trust, morale, communication and support of management showed significant signs of negative workforce response. The paper mill where the safety management system approach was utilised demonstrated a significantly improved safety culture and achieved site ownership from middle managers and supervisors. Research has demonstrated that a solid foundation is required prior to successfully implementing a BBS programme. For a programme to work there must be middle management support in addition to senior management commitment. If a trade union actively distances itself from BBS, it is also unlikely to be effective. This thesis proposes that BBS observation programmes are not suitable for the papermaking industry, particularly when staffing levels are low due to challenging economic conditions. Observers are not available when there are high hazard situations and this suggests that BBS implementation is not the correct intervention for the paper industry.

The ecology of paper mill by-product and its evaluation as a casing medium in the culture of Agaricus bisporus (Lange) Pilat

Effluent from pulp and paper production at the Kemsley mill of Bowaters U.K. Paper Company Limited passes through two treatment stages before its discharge into the Swale estuary. Suspended material removed during treatment is deposited on wasteground as a thin sludge. The solids it contains are mainly wood components lost during pulp production, whilst it also has a high salt content, derived from chemicals used in pulping processes. After deposition the sludge undergoes an ageing process during which it dries out and its salt content is reduced. This ageing can be reproduced and accelerated by improved drainage under controlled conditions. The paper mill sludge was investigated as a casing medium in the culture of Agaricus bisporus (Lange) Pilat, the cultivated mushroom. It was unsuitable up to one year from deposition due largely to the inhibitory effect of its salt content on fruiting. Material eighteen months or more in age gave yields comparable to standard peat casing. Before use as a casing the material must be shredded to a satisfactory structure, neutralised with chalk, and pasteurised to eliminate organisms harmful to the crop. The prepared medium has a high water holding capacity and a structure resilient to management procedures, important requirements of a good casing. A passive movement of salts from the compost to the casing was shown to occur during culture, capable of enhancing the natural decline in cropping if sufficiently great. The ions chloride, potassium, sodium and sulphate were shown to be responsible, their damaging effects being due to high conductivity created in the casing. Studies of elements available during culture suggested phosphate availability in the compost could limit crop potential, whilst iron released by mycelium of A.bisporus in the casing may be utilised by associated micro-organisms.

Computer aided process planning (CAPP) for flat rolling of copper alloys

The manufacture of copper alloy flat rolled metals involves hot and cold rolling operations, together with annealing and other secondary processes, to transform castings (mainly slabs and cakes) into such shapes as strip, plate, sheet, etc. Production is mainly to customer orders in a wide range of specifications for dimensions and properties. However, order quantities are often small and so process planning plays an important role in this industry. Much research work has been done in the past in relation to the technology of flat rolling and the details of the operations, however, there is little or no evidence of any research in the planning of processes for this type of manufacture. Practical observation in a number of rolling mills has established the type of manual process planning traditionally used in this industry. This manual approach, however, has inherent drawbacks, being particularly dependent on the individual planners who gain their knowledge over a long span of practical experience. The introduction of the retrieval CAPP approach to this industry was a first step to reduce these problems. But this could not provide a long-term answer because of the need for an experienced planner to supervise generation of any plan. It also fails to take account of the dynamic nature of the parameters involved in the planning, such as the availability of resources, operation conditions and variations in the costs. The other alternative is the use of a generative approach to planning in the rolling mill context. In this thesis, generative methods are developed for the selection of optimal routes for single orders and then for batches of orders, bearing in mind equipment restrictions, production costs and material yield. The batch order process planning involves the use of a special cluster analysis algorithm for optimal grouping of the orders. This research concentrates on cold-rolling operations. A prototype model of the proposed CAPP system, including both single order and batch order planning options, has been developed and tested on real order data in the industry. The results were satisfactory and compared very favourably with the existing manual and retrieval methods.

Some aspects of system design for production management in the rolling-mill industry

Case studies in copper-alloy rolling mill companies showed that existing planning systems suffer from numerous shortcomings. Where computerised systems are in use, these tend to simply emulate older manual systems and still rely heavily on modification by experienced planners on the shopfloor. As the size and number of orders increase, the task of process planners, while seeking to optimise the manufacturing objectives and keep within the production constraints, becomes extremely complicated because of the number of options for mixing or splitting the orders into batches. This thesis develops a modular approach to computerisation of the production management and planning functions. The full functional specification of each module is discussed, together with practical problems associated with their phased implementation. By adapting the Distributed Bill of Material concept from Material Requirements Planning (MRP) philosophy, the production routes generated by the planning system are broken down to identify the rolling stages required. Then to optimise the use of material at each rolling stage, the system generates an optimal cutting pattern using a new algorithm that produces practical solutions to the cutting stock problem. It is shown that the proposed system can be accommodated on a micro-computer, which brings it into the reach of typical companies in the copper-alloy rolling industry, where profit margins are traditionally low and the cost of widespread use of mainframe computers would be prohibitive.

An experimental analysis of operating conditions in cold roll-forming

A detailed literature survey confirmed cold roll-forming to be a complex and little understood process. In spite of its growing value, the process remains largely un-automated with few principles used in set-up of the rolling mill. This work concentrates on experimental investigations of operating conditions in order to gain a scientific understanding of the process. The operating conditions are; inter-pass distance, roll load, roll speed, horizontal roll alignment. Fifty tests have been carried out under varied operating conditions, measuring section quality and longitudinal straining to give a picture of bending. A channel section was chosen for its simplicity and compatibility with previous work. Quality measurements were measured in terms of vertical bow, twist and cross-sectional geometric accuracy, and a complete method of classifying quality has been devised. The longitudinal strain profile was recorded, by the use of strain gauges attached to the strip surface at five locations. Parameter control is shown to be important in allowing consistency in section quality. At present rolling mills are constructed with large tolerances on operating conditions. By reduction of the variability in parameters, section consistency is maintained and mill down-time is reduced. Roll load, alignment and differential roll speed are all shown to affect quality, and can be used to control quality. Set-up time is reduced by improving the design of the mill so that parameter values can be measured and set, without the need for judgment by eye. Values of parameters can be guided by models of the process, although elements of experience are still unavoidable. Despite increased parameter control, section quality is variable, if only due to variability in strip material properties. Parameters must therefore be changed during rolling. Ideally this can take place by closed-loop feedback control. Future work lies in overcoming the problems connected with this control.

Computer aided form roll design

Cold roll forming is an extremely important but little studied sheet metal forming process. In this thesis, the process of cold roll forming is introduced and it is seen that form roll design is central to the cold roll forming process. The conventional design and manufacture of form rolls is discussed and it is observed that surrounding the design process are a number of activities which although peripheral are time consuming and a possible source of error. A CAD/CAM system is described which alleviates many of the problems traditional to form roll design. New techniques for the calculation of strip length and controlling the means of forming bends are detailed. The CAD/CAM system's advantages and limitations are discussed and, whilst the system has numerous significant advantages, its principal limitation can be said to be the need to manufacture form rolls and test them on a mill before a design can be stated satisfactory. A survey of the previous theoretical and experimental analysis of cold roll forming is presented and is found to be limited. By considering the previous work, a method of numerical analysis of the cold roll forming process is proposed based on a minimum energy approach. Parallel to the numerical analysis, a comprehensive range of software has been developed to enhance the designer's visualisation of the effects of his form roll design. A complementary approach to the analysis of form roll design is the generation of form roll design, a method for the partial generation of designs is described. It is suggested that the two approaches should continue in parallel and that the limitation of each approach is knowledge of the cold roll forming process. Hence, an initial experimental investigation of the rolling of channel sections is described. Finally, areas of potential future work are discussed.

A 'sexy space' for women? Heterosexual women's experiences of a male strip show venue

The rise of male strip shows marketed towards heterosexual women has called into question the idea that only men can 'gaze' or be 'sexual scrutinizers' in public leisure spaces. This paper details the findings of an ethnographic study of a male strip event 'Cheeky's',1 located in the Midlands, England. Utilising observation, informal interviews and photography, the paper describes the physical environment and the atmosphere of the event, and analyses interview data with female customers. The paper questions what spaces such as Cheeky's mean for female sexualities, sexual roles and desires. The findings are twofold. On the one hand the club was a relatively novel sexual space, as some women spectators experienced it as an 'empowering' space in which they could be 'sexually aggressive'; on the other hand, the character of the club was actively and adeptly manufactured by the Master of Ceremonies (MC), and male dancers, so as to encourage - and even to coercively elicit - extrovert behaviour from women customers. Despite shifting normative gendered expectations of women's sexual behaviour to some extent, ultimately the club structured women's sexual experiences around traditional heterosexist lines. The club did not encourage women's autonomous sexual expression, and many women claimed they had not found it a very 'sexy space'. © 2011 Taylor & Francis.

Empowering, degrading or a 'mutually exploitative' exchange For women?: Characterising the power relations of the strip club

This paper seeks to characterise the gendered and sexualised power relations of both female and male strip clubs, and to signal what this means for establishing positive definitions of female desire. It is argued that while it is not useful to present female strippers, or female patrons of male strip clubs as purely passive victims of male heterosexism within these venues, it is equally damaging to assume that these venues represent a whole-scale challenge to conventional oppressive gender and sexual relations for women. Some research has even suggested that both strippers and their patrons are engaged in a 'mutually exploitative' power relationship. Moreover, further empirical research documents key points where female dancers have perhaps wielded 'more' power over patrons at certain moments, and female dancers have highlighted feelings of empowerment and highlighted potential for gender and sexual relations which position women as passive to be subverted within stripping. However, such feelings are often temporally specific and are not applicable to all women in the strip industry. It may be particularly hard for these to manifest in women concentrated in the least economically-rewarding areas of the industry who have less 'power' to resist compromising their bodily boundaries. Furthermore, it is argued that women watching male strippers does little to reverse the 'male gaze', and nor does this male occupation carry as much negative social stigma with it as female stripping suffers. It is thus argued that the overwhelming picture, stemming largely from accounts of former dancers and from empirical studies of individual clubs, suggests these venues in fact do very little to challenge normative hetero-oppressive sexual scripts.