Drop and insert multiplexing with simultaneous clock recovery using an electroabsorption modulator

A three-node optical time-division multiplexing (OTDM) network is demonstrated that utilizes electroabsorption (EA) modulators as the core elements. Each node is self contained and performs its own clock recovery and synchronization. “Drop and insert” functionality is demonstrated for the first time with an EA modulator by completely removing a 10-Gb/s channel from a 40-Gb/s OTDM data stream. A different 10-Gb/s channel was subsequently inserted into the vacant time slot. Clock recovery is achieved by using an EA modulator in a novel bidirectional configuration. Bit-error-rate (BER) measurements are presented for each of the 10-Gb/s OTDM channels.

Postcesarean pelvic floor dysfunction contributes to undisclosed psychosocial morbidity

OBJECTIVE: To estimate the prevalence and severity of postcesarean pelvic dysfunction. STUDY DESIGN: Using biopsychosocial interviewing at home, 184 postcesarean primiparas were compared to 100 vaginally delivered women regarding symptoms of stress incontinence, anal incontinence and dyspareunia. Delivery details were confirmed from medical records. RESULTS: Comparison of postcesarean vs. vaginally delivered women revealed stress incontinence in 33% vs. 54% and dyspareunia in 27% vs. 46%, both differences reaching statistical significance, unlike anal incontinence, which was manifest in 51% vs. 44%. When compared to emergency cesarean the relative risk of stress incontinence following an elective cesarean was 0.99 (0.71, 1.39), of dyspareunia 1.02 and of anal incontinence 1.05, indicating no statistically significant difference. Thirty (22%) stress incontinent and 4 (3%) fecally incontinent mothers used pads continuously, suggesting severe physical morbidity. Severe dysphoria (depression) was expressed by 41 (35%) stress incontinent mothers, 38 (30%) with dyspareunia and 34 (26%) with anal incontinence; the association of severe dysphoria with dyspareunia was statistically significant (OR = 2.504 [1.362, 4.602]). Few women came forward to seek help. CONCLUSION: Pelvic dysfunction was similar after elective or emergency cesarean. Compared to vaginal delivery, postcesarean stress incontinence and dyspareunia were less frequent but biopsychosocial morbidity could be severe.

Psychological therapies for chronic pelvic pain:systematic review of randomized controlled trials

Chronic pelvic pain (CPP), a common cause of disability in women, is a condition best viewed in the biopsychosocial framework. Psychological interventions are frequently considered alongside medical and surgical treatments. Our objective was to evaluate the effectiveness of psychological therapies for the treatment of CPP. Electronic literature searches were conducted in Medline, Embase, PsycInfo and DARE databases from database inception to April 2010. Reference lists of selected articles were searched for further articles. The studies selected were randomized controlled trials of psychological therapies in patients with CPP compared with no treatment, standard gynecological treatment or another form of psychological therapy. Two reviewers independently selected articles without language restrictions and extracted data covering study characteristics, study quality and results. Reduction in pain, measured using visual analog scales or other measurements, was the main outcome measure. Of the 107 citations identified, four studies satisfied the inclusion criteria. Compared with no psychological intervention, therapy produced a standardized mean pain score of -3.27 [95% confidence interval (CI) -4.52 to -2.02] and 1.11 (95% CI -0.05 to 2.27) at 3 months and -3.95 (95% CI -5.35 to -2.55) and 0.54 (95% CI -0.78 to 1.86) at 6 months and greater, based on a visual analog scale score of 0-10. The current evidence does not allow us to conclude whether psychological interventions have an effect on self-reported pain scores in women with CPP.

Flow and pressure drop on the shellside of cylindrical heat exchangers

This work presents pressure distributions and fluid flow patterns on the shellside of a cylindrical shell-and-tube heat exchanger. The apparatus used was constructed from glass enabling direct observation of the flow using a dye release technique and had ten traversable pressure instrumented tubes permitting detailed pressure distributions to be obtained. The `exchanger' had a large tube bundle (278 tubes) and main flow areas typical of practical designs. Six geometries were studied: three baffle spacings both with and without baffle leakage. Results are also presented of three-dimensional modelling of shellside flows using the Harwell Laboratory's FLOW3D code. Flow visualisation provided flow patterns in the central plane of the bundle and adjacent to the shell wall. Comparison of these high-lighted significant radial flow variations. In particular, separated regions, originating from the baffle tips, were observed. The size of these regions was small in the bundle central plane but large adjacent to the shell wall and extended into the bypass lane. This appeared to reduce the bypass flow area and hence the bypass flow fraction. The three-dimensional flow modelling results were presented as velocity vector and isobar maps. The vector maps illustrated regions of high and low velocity which could be prone to tube vibration and fouling. Separated regions were also in evidence. A non-uniform crossflow was discovered with, in general, higher velocities in the central plane of the bundle than near the shell wall._The form of the isobar maps calculated by FLOW3D was in good agreement with experimental results. In particular, larger pressure drops occurred across the inlet than outlet of a crossflow region and were higher near the upstream than downstream baffle face. The effect of baffle spacing and baffle leakage on crossflow and window pressure drop measurements was identified. Agreement between the current measurements, previously obtained data and commonly used design correlations/models was, in general, poor. This was explained in terms of the increased understanding of shellside flow. The bulk of previous data, which dervies from small-scale rigs with few tubes, have been shown to be unrepresentative of typical commerical units. The Heat Transfer and Fluid Flow Service design program TASC provided the best predictions of the current pressure drop results. However, a number of simple one-dimensional models in TASC are, individually, questionable. Some revised models have been proposed.

The Single drop drying of heat-sensitive materials

The literature relating to the principles and practice of drying of materials, particularly those susceptible to thermal degradation or undesirable loss of volatile components, has been reviewed. Single droplets of heat-sensitive materials were dried whilst suspended in a horizontal wind tunnel from a specially-designed, rotating thermocouple which enabled direct observation of drying behaviour and continuous measurement of droplet temperature as drying progressed. The effects of drying air temperature and initial solids concentration on the potency of various antibiotics, viz. ampicillin, chloramphenicol, oxytetracycline, streptomycin and tetracycline, were assessed using a modified Drug Sensitivity Testing technique. Only ampicillin was heat-sensitive at temperatures above 100°C, e.g. at an air temperature of 115°C its zone diameter was reduced from 100% to 45%. Selected enzymes, viz. dextran sucrase and invertase, were also dried and their residual activities determined by High Performance Liquid Chromatography. The residual activity of dextran sucrase was rapidly reduced at temperatures above 65°C, and the residual activity of invertase reduced rapidly at temperatures above 65°C; but drying with short residence times will retain most of its activity. The performance of various skin-forming encapsulants, viz. rice and wheat starch, dextrin, coffee, skim milk, fructose, gelatine 60 and 150 Bloom, and gum arabic, was evaluated to determine their capabilities for retention of ethanol as a model volatile, under different operating conditions. The effects of initial solids concentration, air velocity and temperature were monitored for each material tested. Ethanol content was analysed by Gas Liquid Chromatography and in some cases dried crusts were removed for examination. Volatiles retention was concluded to depend in all cases upon the rate and nature of the skin formation and selective diffusion phenomena. The results provided further insight into the inter-relationship between temperature, residence time and thermal degradation of heat-sensitive materials. They should also assist in selection of the preferred dryer for such materials, and of the operating parameter to enable maximum retention of the required physico-chemical characteristics in the dried materials.

Fibre optic sensors for high speed hypervelocity impact studies and low velocity drop tests

The initial aim of this project was to develop a non-contact fibre optic based displacement sensor to operate in the harsh environment of a 'Light Gas Gun' (LGG), which can 'fire' small particles at velocities ranging from 1-8.4 km/s. The LGG is used extensively for research in aerospace to analyze the effects of high speed impacts on materials. Ideally the measurement should be made close to the centre of the impact to minimise corruption of the data from edge effects and survive the impact. A further requirement is that it should operate at a stand-off distance of ~ 8cm. For these reasons we chose to develop a pseudo con-focal intensity sensor, which demonstrated resolution comparable with conventional PVDF sensors combined with high survivability and low cost. A second sensor was developed based on 'Fibre Bragg Gratings' (FBG) which although requiring contact with the target the low weight and very small contact area had minimal effect on the dynamics of the target. The FBG was mounted either on the surface of the target or tangentially between a fixed location. The output signals from the FBG were interrogated in time by a new method. Measurements were made on composite and aluminium plates in the LGG and on low speed drop tests. The particle momentum for the drop tests was chosen to be similar to that of the particles used in the LGG.

Does post-caesarean dyspareunia reflect sexual malfunction, pelvic floor and perineal dysfunction?

The aim was to define post-caesarean dyspareunia as a sexual and pelvic-perineal symptom. Post-caesarean (80 elective, 104 emergency) and 100 vaginally delivered primiparae had domiciliary interviews at 10 months postpartum. A total of 50 (28% and 27%) post-caesarean and 46 (46%) vaginally delivered, reported dyspareunia. Severely impaired general sexual health occurred in 82 (24% elective, 25% emergency, 35% vaginally delivered) as category 3 (dyspareunia with sexual symptoms) and 27 (10% elective, 7% emergency, 12% vaginally delivered) as category 4 (reduced frequency <6). The risk of dyspareunia (RR 1.14, CI 0.73, 1.77) or impaired general sexual health (RR 0.93, CI 0.32, 2.74) was similar among those with or without perineal trauma. Both caesarean and perineal scars were associated with sexual malfunction. Primiparae with new incontinence had a lower risk of dyspareunia than impaired general sexual health. Awareness of the associations of post-caesarean dyspareunia and impaired general sexual health with incontinence would facilitate appropriate obstetric decision-making. Further research is indicated. © 2011 Informa UK, Ltd.

Drop and insert multiplexing with simultaneous clock recovery using an electroabsorption modulator

A three-node optical time-division multiplexing (OTDM) network is demonstrated that utilizes electroabsorption (EA) modulators as the core elements. Each node is self contained and performs its own clock recovery and synchronization. "Drop and insert" functionality is demonstrated for the first time with an EA modulator by completely removing a 10-Gb/s channel from a 40-Gb/s OTDM data stream. A different 10-Gb/s channel was subsequently inserted into the vacant time slot. Clock recovery is achieved by using an EA modulator in a novel bidirectional configuration. Bit-error-rate (BER) measurements are presented for each of the 10-Gb/s OTDM channels.

First experimental demonstration of terabit interferometric drop, add and extract multiplexer

We present the first experimental implementation of an all-optical ROADM scheme for routing of individual channels within an all-optical OFDM superchannel. The interferometric technique demonstrated enables a fully flexible node, implementing the extraction, drop and addition of individual sub-channel.

A novel architecture for all-optical add-drop multiplexing of OFDM signals

We propose a novel architecture for all-optical add-drop multiplexing of OFDM signals. Extensive numerical simulations have been carried out to benchmark the performance of the architecture against critical design parameters.

Experimental implementation of an all-optical interferometric drop, add, and extract multiplexer for superchannels

We present the experimental implementation of an all-optical ROADM scheme for routing of an individual subchannel within an all-optical OFDM superchannel. The different functions required of optical node were demonstrated using interferometric technique with the extraction, drop, and addition of individual subchannel in a ten subchannels optically aggregated signal. The scheme we reported enables a fully flexible node compatible with future terabit per second superchannel transmission.

Fibre optic sensors for high speed hypervelocity impact studies and low velocity drop tests

The initial aim of this project was to develop a non-contact fibre optic based displacement sensor to operate in the harsh environment of a 'Light Gas Gun' (LGG), which can 'fire' small particles at velocities ranging from 1-8.4 km/s. The LGG is used extensively for research in aerospace to analyze the effects of high speed impacts on materials. Ideally the measurement should be made close to the centre of the impact to minimise corruption of the data from edge effects and survive the impact. A further requirement is that it should operate at a stand-off distance of ~ 8cm. For these reasons we chose to develop a pseudo con-focal intensity sensor, which demonstrated resolution comparable with conventional PVDF sensors combined with high survivability and low cost. A second sensor was developed based on 'Fibre Bragg Gratings' (FBG) which although requiring contact with the target the low weight and very small contact area had minimal effect on the dynamics of the target. The FBG was mounted either on the surface of the target or tangentially between a fixed location. The output signals from the FBG were interrogated in time by a new method. Measurements were made on composite and aluminium plates in the LGG and on low speed drop tests. The particle momentum for the drop tests was chosen to be similar to that of the particles used in the LGG.

All-optical add-drop multiplexing of OFDM signals

We discuss the recently proposed architecture for an all-optical add-drop multiplexer of OFDM signals and we summarize the results of its theoretical design and experimental implementation. © 2015 OSA.

All-optical add-drop multiplexer for OFDM signals

We summarize our research work on the design and development of an add-drop multiplexer for spectrally overlapping OFDM signals. The standard node functions of sub-channel drop, extraction and insertion were obtained whilst the signals remained fully in the optical domain. Numerical simulations have been carried out to identify the main sources of degradation and to benchmark the architectural performance against critical design parameters, whereas the experimental demonstration of the scheme has been achieved for both single quadrature and dual quadrature signals. The reported scheme enables a fully flexible node compatible with future terabit per second super-channel transmission.