Investigation of ultrafast laser-photonic material interactions: Challenges for directly written glass photonics

Currently, direct-write waveguide fabrication is probably the most widely studied application of femtosecond laser micromachining in transparent dielectrics. Devices such as buried waveguides, power splitters, couplers, gratings, and optical amplifiers have all been demonstrated. Waveguide properties depend critically on the sample material properties and writing laser characteristics. In this paper, we discuss the challenges facing researchers using the femtosecond laser direct-write technique with specific emphasis being placed on the suitability of fused silica and phosphate glass as device hosts for different applications.

The ecology of paper mill by-product and its evaluation as a casing medium in the culture of Agaricus bisporus (Lange) Pilat

Effluent from pulp and paper production at the Kemsley mill of Bowaters U.K. Paper Company Limited passes through two treatment stages before its discharge into the Swale estuary. Suspended material removed during treatment is deposited on wasteground as a thin sludge. The solids it contains are mainly wood components lost during pulp production, whilst it also has a high salt content, derived from chemicals used in pulping processes. After deposition the sludge undergoes an ageing process during which it dries out and its salt content is reduced. This ageing can be reproduced and accelerated by improved drainage under controlled conditions. The paper mill sludge was investigated as a casing medium in the culture of Agaricus bisporus (Lange) Pilat, the cultivated mushroom. It was unsuitable up to one year from deposition due largely to the inhibitory effect of its salt content on fruiting. Material eighteen months or more in age gave yields comparable to standard peat casing. Before use as a casing the material must be shredded to a satisfactory structure, neutralised with chalk, and pasteurised to eliminate organisms harmful to the crop. The prepared medium has a high water holding capacity and a structure resilient to management procedures, important requirements of a good casing. A passive movement of salts from the compost to the casing was shown to occur during culture, capable of enhancing the natural decline in cropping if sufficiently great. The ions chloride, potassium, sodium and sulphate were shown to be responsible, their damaging effects being due to high conductivity created in the casing. Studies of elements available during culture suggested phosphate availability in the compost could limit crop potential, whilst iron released by mycelium of A.bisporus in the casing may be utilised by associated micro-organisms.

Sustainable energy from paper industry wastes

Secondary fibre paper mills are significant users of both heat and electricity which is mainly derived from the combustion of fossil fuels. The cost of producing this energy is increasing year upon year. These mills are also significant producers of fibrous sludge and reject waste material which can contain high amounts of useful energy. Currently the majority of these waste fractions are disposed of by landfill, land-spread or incineration using natural gas. These disposal methods not only present environmental problems but are also very costly. The focus of this work was to utilise the waste fractions produced at secondary fibre paper mills for the on-site production of combined heat and power (CHP) using advanced thermal conversion methods (gasification and pyrolysis), well suited to relatively small scales of throughput. The heat and power can either be used on-site or exported. The first stage of the work was the development of methods to condition selected paper industry wastes to enable thermal conversion. This stage required detailed characterisation of the waste streams in terms of proximate and ultimate analysis and heat content. Suitable methods to dry and condition the wastes in preparation for thermal conversion were also explored. Through trials at pilot scale with both fixed bed downdraft gasification and intermediate pyrolysis systems, the energy recovered from selected wastes and waste blends in the form of product gas and pyrolysis products was quantified. The optimal process routes were selected based on the experimental results, and implementation studies were carried out at the selected candidate mills. The studies consider the pre-processing of the wastes, thermal conversion, and full integration of the energy products. The final stage of work was an economic analysis to quantify economic gain, return on investment and environmental benefits from the proposed processes.

Material artifacts:practices for doing strategy with 'stuff'

This paper addresses the dearth of research into material artifacts and how they are engaged in strategizing activities. Building on the strategy-as-practice perspective, and the notion of epistemic objects, we develop a typology of strategy practices that show how managers use material artifacts to strategize by a dual process of knowledge abstraction and substitution. Empirically, we study the practice of underwriting managers in reinsurance companies. Our findings first identify the artifacts – pictures, maps, data packs, spreadsheets and graphs – that these managers use to appraise reinsurance deals. Second, the analysis of each artifact’s situated use led to the identification of five practices for doing strategy with artifacts: physicalizing, locating, enumerating, analyzing, and selecting. Last, we developed a typology that shows how practices vary in terms of their level of abstraction from the physical properties of the risk being reinsured and unfold through a process of substituting. Our conceptual framework extends existing work in the strategy-as-practice field that calls for research into the role of material artifacts.

Material and efficient cause interpretations of the formative model:resolving misunderstandings and clarifying conceptual language

This paper presents a causal explanation of formative variables that unpacks and clarifies the generally accepted idea that formative indicators are ‘causes’ of the focal formative variable. In doing this, we explore the recent paper by Diamantopoulos and Temme (AMS Review, 3(3), 160-171, 2013) and show that the latter misunderstand the stance of Lee, Cadogan, and Chamberlain (AMS Review, 3(1), 3-17, 2013; see also Cadogan, Lee, and Chamberlain, AMS Review, 3(1), 38-49, 2013). By drawing on the multiple ways that one can interpret the idea of causality within the MIMIC model, we then demonstrate how the continued defense of the MIMIC model as a tool to validate formative indicators and to identify formative variables in structural models is misguided. We also present unambiguous recommendations on how formative variables can be modelled in lieu of the formative MIMIC model.

UV-stable paper coated with APTES-modified P25 TiO2 nanoparticles

In order to inhibit the photocatalytic degradation of organic material supports induced by small titania (TiO2) nanoparticles, highly photocatalytically active, commercially available P25-TiO2 nanoparticles were first modified with a thin layer of (3-aminopropyl) triethoxysilane (APTES), which were then deposited and fixed onto the surface of paper samples via a simple, dip-coating process in water at room temperature. The resultant APTES-modified P25 TiO2 nanoparticle-coated paper samples exhibit much greater stability to UV-illumination than uncoated blank reference paper. Very little, or no, photo-degradation in terms of brightness and whiteness, respectively, of the P25-TiO2-nanoparticle-treated paper is observed. There are many other potential applications for this Green Chemistry approach to protect cellulosic fibres from UV-bleaching in sunlight and to protect their whiteness and maintain their brightness. © 2014 Elsevier Ltd.

The effects of material variations in high value manufacturing industries

It has never been easy for manufacturing companies to understand their confidence level in terms of how accurate and to what degree of flexibility parts can be made. This brings uncertainty in finding the most suitable manufacturing method as well as in controlling their product and process verification systems. The aim of this research is to develop a system for capturing the company’s knowledge and expertise and then reflect it into an MRP (Manufacturing Resource Planning) system. A key activity here is measuring manufacturing and machining capabilities to a reasonable confidence level. For this purpose an in-line control measurement system is introduced to the company. Using SPC (Statistical Process Control) not only helps to predict the trend in manufacturing of parts but also minimises the human error in measurement. Gauge R&R (Repeatability and Reproducibility) study identifies problems in measurement systems. Measurement is like any other process in terms of variability. Reducing this variation via an automated machine probing system helps to avoid defects in future products.Developments in aerospace, nuclear, oil and gas industries demand materials with high performance and high temperature resistance under corrosive and oxidising environments. Superalloys were developed in the latter half of the 20th century as high strength materials for such purposes. For the same characteristics superalloys are considered as difficult-to-cut alloys when it comes to formation and machining. Furthermore due to the sensitivity of superalloy applications, in many cases they should be manufactured with tight tolerances. In addition superalloys, specifically Nickel based, have unique features such as low thermal conductivity due to having a high amount of Nickel in their material composition. This causes a high surface temperature on the work-piece at the machining stage which leads to deformation in the final product.Like every process, the material variations have a significant impact on machining quality. The main cause of variations can originate from chemical composition and mechanical hardness. The non-uniform distribution of metal elements is a major source of variation in metallurgical structures. Different heat treatment standards are designed for processing the material to the desired hardness levels based on application. In order to take corrective actions, a study on the material aspects of superalloys has been conducted. In this study samples from different batches of material have been analysed. This involved material preparation for microscopy analysis, and the effect of chemical compositions on hardness (before and after heat treatment). Some of the results are discussed and presented in this paper.

Eco-efficiency measurement and material balance principle:an application in power plants Malmquist Luenberger Index

Incorporating Material Balance Principle (MBP) in industrial and agricultural performance measurement systems with pollutant factors has been on the rise in recent years. Many conventional methods of performance measurement have proven incompatible with the material flow conditions. This study will address the issue of eco-efficiency measurement adjusted for pollution, taking into account materials flow conditions and the MBP requirements, in order to provide ‘real’ measures of performance that can serve as guides when making policies. We develop a new approach by integrating slacks-based measure to enhance the Malmquist Luenberger Index by a material balance condition that reflects the conservation of matter. This model is compared with a similar model, which incorporates MBP using the trade-off approach to measure productivity and eco-efficiency trends of power plants. Results reveal similar findings for both models substantiating robustness and applicability of the proposed model in this paper.

Solar stills:a comprehensive review of designs, performance and material advances

The demand for fresh water production is growing day by day with the increase in world population and with industrial growth. Use of desalination technology is increasing to meet this demand. Among desalination technologies, solar stills require low maintenance and are readily affordable; however their productivity is limited. This paper aims to give a detailed review about the various types of solar stills, covering passive and active designs, single- and multi-effect types, and the various modifications for improved productivity including reflectors, heat storage, fins, collectors, condensers, and mechanisms for enhancing heat and mass transfer. Photovoltaic-thermal and greenhouse type solar stills are also covered. Material advances in the area of phase change materials and nanocomposites are very promising to enhance further performance; future research should be carried out in these and other areas for the greater uptake of solar still technology.

An alternative to BlackboardTM? Student use of web-based textbook teaching and learning material

This paper investigates the use of web-based textbook supplementary teaching and learning materials which include multiple choice test banks, animated demonstrations, simulations, quizzes and electronic versions of the text. To gauge their experience of the web-based material students were asked to score the main elements of the material in terms of usefulness. In general it was found that while the electronic text provides a flexible platform for presentation of material there is a need for continued monitoring of student use of this material as the literature suggests that digital viewing habits may mean there is little time spent in evaluating information, either for relevance, accuracy or authority. From a lecturer perspective these materials may provide an effective and efficient way of presenting teaching and learning materials to the students in a variety of multimedia formats, but at this stage do not overcome the need for a VLE such as Blackboard™.