Melting of polymers

The project set out to investigate the relative effectiveness of thermal conductive heating (from external resistance heaters) and viscous heating in the heating (and melting) of low density polyethylene. A model system was used in order to simplify the mathematical analysis. A theory was developed to describe both processes in the model apparatus. The results showed large differences between the experimental and predicted results at low melt temperatures (the predicted results were much greater than the experimental) . Analysis of the results indicated that the apparatus was probably not producing the required shear rates in the sample. The theory appeared to be satisfactory, in that it did not over estimate the viscous heating to any significant extent. The theoretical results could therefore be considered to be a reasonable estimate of the viscous heating.

Melting and solidification of Zinc-Aluminium alloys

Following a scene-setting introduction are detailed reviews of the relevant scientific principles, thermal analysis as a research tool and the development of the zinc-aluminium family of alloys. A recently introduced simultaneous thermal analyser, the STA 1500, its use for differential thermal analysis (DTA) being central to the investigation, is described, together with the sources of support information, chemical analysis, scanning electron microscopy, ingot cooling curves and fluidity spiral castings. The compositions of alloys tested were from the binary zinc-aluminium system, the ternary zinc-aluminium-silicon system at 30%, 50% and 70% aluminium levels, binary and ternary alloys with additions of copper and magnesium to simulate commercial alloys and five widely used commercial alloys. Each alloy was shotted to provide the smaller, 100mg, representative sample required for DTA. The STA 1500 was characterised and calibrated with commercially pure zinc, and an experimental procedure established for the determination of DTA heating curves at 10°C per minute and cooling curves at 2°C per minute. Phase change temperatures were taken from DTA traces, most importantly, liquidus from a cooling curve and solidus from both heating and cooling curves. The accepted zinc-aluminium binary phase diagram was endorsed with the added detail that the eutectic is at 5.2% aluminium rather than 5.0%. The ternary eutectic trough was found to run through the points, 70% Al, 7.1% Si, 545°C; 50% Al, 3.9% Si, 520°C; 30% Al, 1.4% Si, 482°C. The dendrite arm spacing in samples after DTA increased with increasing aluminium content from 130m at 30% to 220m at 70%. The smallest dendrite arm spacing of 60m was in the 30% aluminium 2% silicon alloy. A 1kg ingot of the 10% aluminium binary alloy, insulated with Kaowool, solidified at the same 2°C per minute rate as the DTA samples. A similar sized sand casting was solidified at 3°C per minute and a chill casting at 27°C per minute. During metallographic examination the following features were observed: heavily cored phase which decomposed into ' and '' on cooling; needles of the intermetallic phase FeAl4; copper containing ternary eutectic and copper rich T phase.

ICT and internet use at the household levels:a melting pot of sub-optimum decision making in the case of E-Grocery shopping

Research shows that consumers are readily embracing the Internet to buy products. This paper proposes that, in the case of grocery shopping, this may lead to sub-optimal decisions at the household level. Decisions online on what, where and from who to buy are normally taken by one individual. In the case of grocery shopping, decisions, however, need to be ‘vetted’ by ‘other’ individuals within the household. The ‘household wide related’ decisions influence how information technologies and systems for commerce should be designed and managed for optimum decision making. This paper argues, unlike previous research, that e-grocery retailing is failing to grow to its full potential not solely because of the ‘classical’ hazards and perceived risks associated with doing grocery shopping online but because e-grocery retailing strategy has failed to acknowledge the micro-household level specificities that affect decision making. Our exploratory research is based on empirical evidence which were collected through telephone interviews. We offer an insight into how e-grocery ‘fits’ and is ‘disrupted’ by the reality of day to day consumption decision making at the household level. Our main finding is to advocate a more role-neutral, multi-user and multi-technology approach to e-grocery shopping which re-defines the concept of the main shopper/decision maker thereby reconceptualising the ‘shopping logic’ for grocery products.