Cost and performance analysis of new wood-fuelled power plant concepts

The objective of the thesis was to analyse several process configurations for the production of electricity from biomass. Process simulation models using AspenPlus aimed at calculating the industrial performance of power plant concepts were built, tested, and used for analysis. The criteria used in analysis were performance and cost. All of the advanced systems appear to have higher efficiencies than the commercial reference, the Rankine cycle. However, advanced systems typically have a higher cost of electricity (COE) than the Rankine power plant. High efficiencies do not reduce fuel costs enough to compensate for the high capital costs of advanced concepts. The successful reduction of capital costs would appear to be the key to the introduction of the new systems. Capital costs account for a considerable, often dominant, part of the cost of electricity in these concepts. All of the systems have higher specific investment costs than the conventional industrial alternative, i.e. the Rankine power plant; Combined beat and power production (CUP) is currently the only industrial area of application in which bio-power costs can be considerably reduced to make them competitive. Based on the results of this work, AsperiPlus is an appropriate simulation platform. How-ever, the usefulness of the models could be improved if a number of unit operations were modelled in greater detail. The dryer, gasifier, fast pyrolysis, gas engine and gas turbine models could be improved.

An investigation of the factor-analytic approach to the determination of abilities involved in psychomotor learning

This research began with an attempt to solve a practical problem, namely, the prediction of the rate at which an operator will learn a task. From a review of the literature, communications with researchers in this area and the study of psychomotor learning in factories it was concluded that a more fundamental approach was required which included the development of a task taxonomy. This latter objective had been researched for over twenty years by E. A. Fleishman and his approach was adopted. Three studies were carried out to develop and extend Fleishman's approach to the industrial area. However, the results of these studies were not in accord with FIeishman's conclusions and suggested that a critical re-assessment was required of the arguments, methods and procedures used by Fleishman and his co-workers. It was concluded that Fleishman's findings were to some extent an artifact of the approximate methods and procedures which he used in the original factor analyses and that using the more modern computerised factor analytic methods a reliable ability taxonomy could be developed to describe the abilities involved in the learning of psychomotor tasks. The implications for a changing-task or changing-subject model were drawn and it was concluded that a changing task and subject model needs to be developed.

Cadmium in the environment and high risk population groups

Cadmium has been widely used in various industries for the past fifty years, with current world production standing at around 16,755 tonnes per year. Very little cadmium is ever recycled and the ultimate fate of all cadmium is the environment. In view of reports that cadmium in the environment is increasing, this thesis aims to identify population groups 'at risk' of receiving dietary intakes of cadmium up to or above the current Food and Agricultural Organisation/World Health Organisation maximum tolerable intake of 70 ug/day. The study involves the investigation of one hundred households (260 individuals) who grow a large proportion of their vegetable diet in garden soils in the Borough of Walsall, part of an urban/industrial area in the United Kingdom. Measurements were made of the cadmium levels in atmospheric deposition, soil, house dust, diet and urine from the participants. Atmospheric deposition of cadmium was found to be comparable with other urban/industrial areas in the European Community, with deposition rates as high as 209 g ha-1 yr-1. The garden soils of the study households were found to contain up to 33 mg kg-1 total cadmium, eleven times the highest level usually found in agricultural soils. Dietary intakes of cadmium by the residents from food were calculated to be as high as 68 ug/day. It is suggested that with intakes from other sources, such as air, adventitious ingestion, smoking and occupational exposure, total intakes of cadmium may reach or exceed the FAO/WHO limit. Urinary excretion of cadmium amongst a non-smoking, non-occupationally exposed sub-group of the study population was found to be significantly higher than that of a similar urban population who did not rely on home-produced vegetables. The results from this research indicate that present levels of cadmium in urban/industrial areas can increase dietary intakes and body burdens of cadmium. As cadmium serves no useful biological function and has been found to be highly toxic, it is recommended that policy measures to reduce human exposure on the European scale be considered.

A study on the flow characteristics of an industrial radiant tube burner

The thesis presents an experimentally validated modelling study of the flow of combustion air in an industrial radiant tube burner (RTB). The RTB is used typically in industrial heat treating furnaces. The work has been initiated because of the need for improvements in burner lifetime and performance which are related to the fluid mechanics of the com busting flow, and a fundamental understanding of this is therefore necessary. To achieve this, a detailed three-dimensional Computational Fluid Dynamics (CFD) model has been used, validated with experimental air flow, temperature and flue gas measurements. Initially, the work programme is presented and the theory behind RTB design and operation in addition to the theory behind swirling flows and methane combustion. NOx reduction techniques are discussed and numerical modelling of combusting flows is detailed in this section. The importance of turbulence, radiation and combustion modelling is highlighted, as well as the numerical schemes that incorporate discretization, finite volume theory and convergence. The study first focuses on the combustion air flow and its delivery to the combustion zone. An isothermal computational model was developed to allow the examination of the flow characteristics as it enters the burner and progresses through the various sections prior to the discharge face in the combustion area. Important features identified include the air recuperator swirler coil, the step ring, the primary/secondary air splitting flame tube and the fuel nozzle. It was revealed that the effectiveness of the air recuperator swirler is significantly compromised by the need for a generous assembly tolerance. Also, there is a substantial circumferential flow maldistribution introduced by the swirier, but that this is effectively removed by the positioning of a ring constriction in the downstream passage. Computations using the k-ε turbulence model show good agreement with experimentally measured velocity profiles in the combustion zone and proved the use of the modelling strategy prior to the combustion study. Reasonable mesh independence was obtained with 200,000 nodes. Agreement was poorer with the RNG  k-ε and Reynolds Stress models. The study continues to address the combustion process itself and the heat transfer process internal to the RTB. A series of combustion and radiation model configurations were developed and the optimum combination of the Eddy Dissipation (ED) combustion model and the Discrete Transfer (DT) radiation model was used successfully to validate a burner experimental test. The previously cold flow validated k-ε turbulence model was used and reasonable mesh independence was obtained with 300,000 nodes. The combination showed good agreement with temperature measurements in the inner and outer walls of the burner, as well as with flue gas composition measured at the exhaust. The inner tube wall temperature predictions validated the experimental measurements in the largest portion of the thermocouple locations, highlighting a small flame bias to one side, although the model slightly over predicts the temperatures towards the downstream end of the inner tube. NOx emissions were initially over predicted, however, the use of a combustion flame temperature limiting subroutine allowed convergence to the experimental value of 451 ppmv. With the validated model, the effectiveness of certain RTB features identified previously is analysed, and an analysis of the energy transfers throughout the burner is presented, to identify the dominant mechanisms in each region. The optimum turbulence-combustion-radiation model selection was then the baseline for further model development. One of these models, an eccentrically positioned flame tube model highlights the failure mode of the RTB during long term operation. Other models were developed to address NOx reduction and improvement of the flame profile in the burner combustion zone. These included a modified fuel nozzle design, with 12 circular section fuel ports, which demonstrates a longer and more symmetric flame, although with limited success in NOx reduction. In addition, a zero bypass swirler coil model was developed that highlights the effect of the stronger swirling combustion flow. A reduced diameter and a 20 mm forward displaced flame tube model shows limited success in NOx reduction; although the latter demonstrated improvements in the discharge face heat distribution and improvements in the flame symmetry. Finally, Flue Gas Recirculation (FGR) modelling attempts indicate the difficulty of the application of this NOx reduction technique in the Wellman RTB. Recommendations for further work are made that include design mitigations for the fuel nozzle and further burner modelling is suggested to improve computational validation. The introduction of fuel staging is proposed, as well as a modification in the inner tube to enhance the effect of FGR.

New technology, industrial relations and white collar trade unions : the case of the National and Local Government Officers Association

The decade since 1979 has seen the most rapid introduction of microelectronic technology in the workplace. In particular, the scope offered for the application of this new technology to the area of white collar work has meant that it is a sector where trade unions have been confronted with major challenges. However the application of this technology has also provided trade unions with opportunities for exerting influence to reshape traditional attitudes to both industrial relations and the nature of work. Recent academic research on the trade union response to the introduction of new technology at the workplace suggests that, despite the resources and apparent sophistication of modern trade unions, they have not in general been able to take advantage of the opportunities offered during this period of radical technological change,the argument being that this is due both to structural weaknesses and the inappropriateness of the system of collective bargaining where new technology issues are concerned. Despite the significance of the Public Sector in employment terms, research into the response of public sector white collar trade unions to technological change has been fairly limited. This thesis sets out the approach of the National and Local Government Officers Association (NALGO), the largest solely white collar union in the world with over three quarters of a million members employed in a wide range of public service industries. The thesis examines NALGO's response at national level and, through detailed case studies, at local level in respect of Local Government and Water Industry NALGO members. The response is then evaluated and conclusions drawn in terms of a framework based upon an assessment of the key factors relevant in judging the ability of NALGO to respond effectively to the challenges brought about by the technological revolution of the last ten years.

Business cycles, long waves, and company langevity in Birmingham area metal industries 1780-1980

This doctoral thesis originates from an observational incongruence between the perennial aims and aspirations of economic endeavour and actually recorded outcomes, which frequently seem contrary to those intended and of a recurrent, cyclical type. The research hypothesizes parallel movement between unstable business environments through time, as expressed by periodically fluctuating levels of economic activity, and the precipitation rates of industrial production companies. A major problem arose from the need to provide theoretical and empirical cohesion from the conflicting, partial and fragmented interpretations of several hundred historians and economists, without which the research question would remain unanswerable. An attempt to discover a master cycle, or superimposition theorem, failed, but was replaced by minute analysis of both the concept of cycles and their underlying data-bases. A novel technique of congregational analysis emerged, resulting in an integrated matrix of numerical history. Two centuries of industrial revolution history in England and Wales was then explored and recomposed for the first time in a single account of change, thereby providing a factual basis for the matrix. The accompanying history of the Birmingham area provided the context of research into the failure rates and longevities of firms in the city's staple metal industries. Sample specific results are obtained for company longevities in the Birmingham area. Some novel presentational forms are deployed for results of a postal questionnaire to surviving firms. Practical demonstration of the new index of national economic activity (INEA) in relation to company insolvencies leads to conclusions and suggestions for further applications of research into the tempo of change, substantial Appendices support the thesis and provide a compendium of information covering immediately contiguous domains.

Identification of industrial sources of airborne heavy metal pollution in urban areas

The research examines the deposition of airborne particles which contain heavy metals and investigates the methods that can be used to identify their sources. The research focuses on lead and cadmium because these two metals are of growing public and scientific concern on environmental health grounds. The research consists of three distinct parts. The first is the development and evaluation of a new deposition measurement instrument - the deposit cannister - designed specifically for large-scale surveys in urban areas. The deposit cannister is specifically designed to be cheap, robust, and versatile and therefore to permit comprehensive high-density urban surveys. The siting policy reduces contamination from locally resuspended surface-dust. The second part of the research has involved detailed surveys of heavy metal deposition in Walsall, West Midlands, using the new high-density measurement method. The main survey, conducted over a six-week period in November - December 1982, provided 30-day samples of deposition at 250 different sites. The results have been used to examine the magnitude and spatial variability of deposition rates in the case-study area, and to evaluate the performance of the measurement method. The third part of the research has been to conduct a 'source-identification' exercise. The methods used have been Receptor Models - Factor Analysis and Cluster Analysis - and a predictive source-based deposition model. The results indicate that there are six main source processes contributing to deposition of metals in the Walsall area: coal combustion, vehicle emissions, ironfounding, copper refining and two general industrial/urban processes. |A source-based deposition model has been calibrated using facctorscores for one source factor as the dependent variable, rather than metal deposition rates, thus avoiding problems traditionally encountered in calibrating models in complex multi-source areas. Empirical evidence supports the hypothesised associatlon of this factor with emissions of metals from the ironfoundry industry.

Energy conservation measures on an industrial site

World and UK energy resources and use are reviewed and the role of energy conservation in energy policy identified. In considering various energy conservation measures, a distinction is made between energy intensive and non-intensive industries and also between direct and indirect uses of energy. Particular attention is given to the non-intensive user of energy. Energy use on one such industrial site has been studied to determine the most effective energy saving measures in the short term. Here it is estimated that over 65% of energy is consumed for indirect purposes, mainly for heating and lighting buildings. Emphasis is placed on energy auditing techniques and those energy saving measures requiring greater technical, economic and organisational resources to secure their implementation. Energy auditing techniques include the use of aerial thermography and snow formation surveys to detect heat losses. Qualitative and quantitative interpretations are carried out, but restricted mainly to evaluating building roof heat losses. From the energy auditing exercise, it is confirmed that the intermittent heating of buildings is the largest and most cost effective fuel saving measure. This was implemented on the site and a heat monitoring programme established to verify results. Industrial combined heat and power generation is investigated. A proposal for the site demonstrates that there are several obstacles to its successful implementation. By adopting an alternative financial rationale, a way of overcoming these obstacles is suggested. A useful by-product of the study is the classification of industrial sites according to the nature of industrial energy demand patterns. Finally, energy saving measures implemented on the site are quantlfied using comparative verification methods. Overall fuel savings of 13% are indicated. Cumulative savings in heating fuel amount to 26% over four years although heated area increased by approximately 25%.

The management of diversification in a large industrial company

This work is the result of an action-research-type study of the diversification effort of part of a major U.K. industrial company. Work in contingency theory concerning the impact of environmental factors on organizational design, and the systemic model of viable systems put forward by Stafford Beer form the theoretical basis of the vvork. The two streams of thought are compared and found to offer similar conclusions about the design of effective organizations. These findings are taken as the framework for an analysis both of organization structures for promoting innovation described in the literature, and of those employed by the company for this purpose in recent years. Much attention is given to the use of venture groups, and conclusions are drawn on particular factors which may influence their success or failure. Both theoretical considerations, and the examination of the company' s recent experience suggested that the formation of the policy of diversification, as well as the method of implementation of the police, might affect its outcorre. Attention is therefore focused on the policy-making and planning process, and in particular on possible problems that this process could generate in a multi-division company. The view finally taken of diversification effort is that it should be regarded as a learning system. This view helps to expose some ambiguities in the concepts of success and failure in this area, and demonstrates considerable weaknesses in traditional project evaluation procedures.

Industrial new product planning:a study of the sources of new product ideas and the development of new product proposals in the UK computer industry

This thesis presents a study of the sources of new product ideas and the development of new product proposals in an organisation in the UK Computer Industry. The thesis extends the work of von Hippel by showing how the phenomenon which he describes as "the Customer Active Paradigm for new product idea generation" can be observed to operate in this Industry. Furthermore, this thesis contrasts his Customer Active Paradigm with the more usually encountered Manufacturer Active Paradigm. In a second area, the thesis draws a number of conclusions relating to methods of market research, confirming existing observations and demonstrating the suitability of flexible interview strategies in certain circumstances. The thesis goes on to demonstrate the importance of free information flow within the organisation, making it more likely that sought and unsought opportunities can be exploited. It is shown that formal information flows and documents are a necessary but not sufficient means of influencing the formation of the organisation's dominant ideas on new product areas. The findings also link the work of Tushman and Katz on the role of "Gatekeepers" with the work of von Hippel by showing that the role of gatekeeper is particularly appropriate and useful to an organisation changing from Customer Active to Manufacturer Active methods of idea generation. Finally, the thesis provides conclusions relating to the exploitation of specific new product opportunities facing the sponsoring organisation.

Optical fibre sensors and their applications in the industrial weighing and aerospace industries

This thesis presents the design, fabrication and testing of novel grating based Optical Fibre Sensor (OFS) systems being interrogated using “off the shelf” interrogation systems, with the eventual development of marketable commercial systems at the forefront of the research. Both in the industrial weighing and aerospace industries, there has been a drive to investigate the feasibility of using optical fibre sensors being deployed where traditionally their electrical or mechanical counterparts would traditionally have been. Already, in the industrial weighing industry, commercial operators are deploying OFS-based Weigh-In-Motion (WIM) systems. Likewise, in the aerospace industry, OFS have been deployed to monitor such parameters as load history, impact detection, structural damage, overload detection, centre of gravity and the determination of blade shape. Based on the intrinsic properties of fibre Bragg gratings (FBGs) and Long Period Fibre Gratings (LPFGs), a number of novel OFS-based systems have been realised. Experimental work has shown that in the case of static industrial weighing, FBGs can be integrated with current commercial products and used to detect applied loads. The work has also shown that embedding FBGs in e-glass, to form a sensing patch, can result in said patches being bonded to rail track, forming the basis of an FBG-based WIM system. The results obtained have been sufficiently encouraging to the industrial partner that this work will be progressed beyond the scope of the work presented in this thesis. Likewise, and to the best of the author’s knowledge, a novel Bragg grating based systems for aircraft fuel parameter sensing has been presented. FBG-based pressure sensors have been shown to demonstrate good sensitivity, linearity and repeatability, whilst LPFG-based systems have demonstrated a far greater sensitivity when compared to FBGs, as well the advantage of being potentially able to detect causes of fuel adulteration based on their sensitivity to refractive index (RI). In the case of the LPFG-based system, considerable work remains to be done on the mechanical strengthening to improve its survivability in a live aircraft fuel tank environment. The FBG system has already been developed to an aerospace compliant prototype and is due to be tested at the fuel testing facility based at Airbus, Filton, UK. It is envisaged by the author that in both application areas, continued research in this area will lead to the eventual development of marketable commercial products.

A European competence framework for industrial pharmacy practice in biotechnology

Project Report: The PHAR-IN ("Competences for industrial pharmacy practice in biotechnology") looked at whether there is a difference in how industrial employees and academics rank competences for practice in the biotechnological industry. A small expert panel consisting of the authors of this paper produced a biotechnology competence framework by drawing up an initial list of competences then ranking them in importance using a three-stage Delphi process. The framework was next evaluated and validated by a large expert panel of academics (n = 37) and industrial employees (n = 154). Results show that priorities for industrial employees and academics were similar. The competences for biotechnology practice that received the highest scores were mainly in: . "Research and Development", . "Upstream" and "Downstream" Processing', " . "Product development and formulation", " . "Aseptic processing", ."Analytical methodology", . "Product stability", and . "Regulation". The main area of disagreement was in the category "Ethics and drug safety" where academics ranked competences higher than did industrial employees.