The ecology of paper mill by-product and its evaluation as a casing medium in the culture of Agaricus bisporus (Lange) Pilat

Effluent from pulp and paper production at the Kemsley mill of Bowaters U.K. Paper Company Limited passes through two treatment stages before its discharge into the Swale estuary. Suspended material removed during treatment is deposited on wasteground as a thin sludge. The solids it contains are mainly wood components lost during pulp production, whilst it also has a high salt content, derived from chemicals used in pulping processes. After deposition the sludge undergoes an ageing process during which it dries out and its salt content is reduced. This ageing can be reproduced and accelerated by improved drainage under controlled conditions. The paper mill sludge was investigated as a casing medium in the culture of Agaricus bisporus (Lange) Pilat, the cultivated mushroom. It was unsuitable up to one year from deposition due largely to the inhibitory effect of its salt content on fruiting. Material eighteen months or more in age gave yields comparable to standard peat casing. Before use as a casing the material must be shredded to a satisfactory structure, neutralised with chalk, and pasteurised to eliminate organisms harmful to the crop. The prepared medium has a high water holding capacity and a structure resilient to management procedures, important requirements of a good casing. A passive movement of salts from the compost to the casing was shown to occur during culture, capable of enhancing the natural decline in cropping if sufficiently great. The ions chloride, potassium, sodium and sulphate were shown to be responsible, their damaging effects being due to high conductivity created in the casing. Studies of elements available during culture suggested phosphate availability in the compost could limit crop potential, whilst iron released by mycelium of A.bisporus in the casing may be utilised by associated micro-organisms.

Protein interactions studied by SAXS:effect of ionic strength and protein concentration for BSA in aqueous solutions

We have studied a series of samples of bovine serum albumin (BSA) solutions with protein concentration, c, ranging from 2 to 500 mg/mL and ionic strength, I, from 0 to 2 M by small-angle X-ray scattering (SAXS). The scattering intensity distribution was compared to simulations using an oblate ellipsoid form factor with radii of 17 x 42 x 42 A, combined with either a screened Coulomb, repulsive structure factor, S-SC(q), or an attractive square-well structure factor, S-SW(q). At pH = 7, BSA is negatively charged. At low ionic strength, I <0.3 M, the total interaction exhibits a decrease of the repulsive interaction when compared to the salt-free solution, as the net surface charge is screened, and the data can be fitted by assuming an ellipsoid form factor and screened Coulomb interaction. At moderate ionic strength (0.3-0.5 M), the interaction is rather weak, and a hard-sphere structure factor has been used to simulate the data with a higher volume fraction. Upon further increase of the ionic strength (I >= 1.0 M), the overall interaction potential was dominated by an additional attractive potential, and the data could be successfully fitted by an ellipsoid form factor and a square-well potential model. The fit parameters, well depth and well width, indicate that the attractive potential caused by a high salt concentration is weak and long-ranged. Although the long-range, attractive potential dominated the protein interaction, no gelation or precipitation was observed in any of the samples. This is explained by the increase of a short-range, repulsive interaction between protein molecules by forming a hydration layer with increasing salt concentration. The competition between long-range, attractive and short-range, repulsive interactions accounted for the stability of concentrated BSA solution at high ionic strength.

Drinking while thirsty can lead to conditioned increases in consumption

A within-subject design was used to test whether repeatedly drinking a novel-flavoured and coloured drink while thirsty would influence subsequent liking for or consumption of that drink, compared to a different flavoured and coloured drink repeatedly consumed while less thirsty. Each participant was given 300 ml of one flavoured drink (H) after consuming a high salt meal (5.27 g of salt), and 300 ml of another flavoured drink (L) after consuming a low salt meal (1.27 g of salt). Participants had 4 sessions with each meal-type/drink combination, in an intermixed order. Pre- and post-training assessments of the drinks were conducted to determine the impact of the training regime on pleasantness and perceived thirst-quenching effect of the drinks. The final session included a choice test, and ad libitum access to the chosen drink, after either a high or low salt meal. In this final choice session, people drank almost twice as much H as L; however, there were no differential effects of past training on rated liking or choice. The increased consumption of H might reflect greater liking for H which was not detected by the rating scales; or it might reflect the learning of greater "conditioned thirst" in response to the flavour of H. © 2002 Elsevier Science Ltd. All rights reserved.

Novel high water content hydrogels

Hydrogels may be described as cross-linked hydrophilic polymers that swell but do not dissolve in water. The production of high water content hydrogels was the subject of investigation. Based upon copolymer compositions that had already achieved commercial success as biomaterials, new monomers were added or substituted in and the effects observed. The addition of N-isopropyl acrylamide to an acrylamide-based composition that had previously been designed to become a contact lens, produced materials that showed smart effects in that the water content showed dependence on the temperature of the hydrating solution. Such thermo-responsive materials have potential uses in drug delivery, ultrafiltration and cell culture surfaces. Proteoglycans in nature have an important role to play in structural support where a highly hydrophilic structure maintains lubricious surfaces. Certain functional groups that impart this hydrophilicity are present in certain sulphonate monomers, Bis(3-sulphopropyl ester) itaconate, dipotassium salt (SPI), 3-Sulphopropyl ester acrylate, potassium salt (SPA) and Sodium 2-(acrylamido)-2-methyl propane sulphonate (NaAMPS). These monomers were incorporated into a HEMA-based copolymer that had been designed initially as a contact lens and the resulting effects examined. Highly hydrophilic materials resulted that showed reduced protein deposition over the neutral core material. It is postulated that a sulphonate group would have a larger number of hydration shells around it than for example methacrylic acid, leading to more dynamic exchange and so reducing the adsorption of biological solutes. A cationic monomer was added to bring back the net anionic nature of the sulphonate hydrogels and the effects studied. Ionic interactions were found to cause a reduction in the water content of the resulting materials as the mobility of the network decreased, leading to stiffer but less extensible materials. The presence of a net dominant charge, whether negative or positive, appeared to act to reduce protein deposition, but increasing equivalence in the amount of both charges served to present a more 'neutral' surface and deposition subsequently increased. The grafting of hydrophilic hydrogel layers onto silicone elastomer was attempted and the results evaluated using dynamic contact angle measurements. Following plasma oxidation to reduce the surface energy barrier to aqueous grafting chemistry, it was found that the wettability of the modified elastomers could be significantly enhanced by such treatment. The SPA-grafted material in particular hinted at an osmotic drive for rehydration that may be exploited in biomaterials.

Renal dopamine and salt-retaining states

Although generally regarded as a neurotransmitter, dopamine is also known to be secreted by the kidney whereby it promotes sodium excretion in its role as a natriuretic honnone. Peripheral dopamine may be formed by two alternative pathways; the decarboxylation of circulating L-Dopa by L-aromatic amino acid decarboxylase (LAAAD), and the desulphation of dopamine sulphate by arylsulphatase A (ASA), the latter being poorly represented in the literature. In many conditions and diseases with which sodium retention is associated, a reduced urinary excretion of dopamine has been noted implicating the involvement of dopamine in the maintenance of sodium homeostasis.This study investigates renal dopamine production via the desulphation of dopamine sulphate in a sample cohort during normal unregulated dietary sodium intake and following a low sodium regimen. After dietary salt restriction urinary dopamine sulphate levels were significantly increased, indicating that dopamine sulphate is indeed a physiological reservoir of active free dopamine, the necessity for which is reduced during self depletion. This confirmed the dopamine/dopamine sulphate pathway as one which may be relevant to the maintenance of sodium homeostasis. The activity of urinary ASA was investigated in diabetes mellitus as an example of a sodium-retaining state, and compared with that in a matched normal control group. A decreased ASA activity was anticipated, given the blunted dopamine excretion observed in many sodium-retaining states, however an unexpected increase in activity in the diabetic group was observed. Enzyme kinetic analysis of ASA showed that this was not due to the existence of an isoform having an altered affinity for dopamine sulphate. This rather paradoxical situation, that urinary-dopamine is decreased while ASA activity is increased, may be explained by the sequestering of free dopamine by autoxidation to 6-hydroxydopamine as has been hypothesised recently to occur in diabetes mellitus. To confirm the homogeneity of ASA in the normal and diabetic groups, four amplicons spanning the 3637bp intronic and exonic regions of the gene were generated by PCR. These were sequence utilising a fluorescent-dye terminator reaction using the forward PCR primer as sequencing primer. Although single nucleotide polymorphisms were observed between the two groups these occurred either in intronic regions or, when exonic, generated silent mutations, supporting the enzyme kinetic data. The expression of ASA was investigated to determine the basis of the increased activity observed in diabetes mellitus. Although a validated comparative RT-PCR assay was developed for amplification of arsa transcripts from fresh blood samples, expression analysis from archived paraffin-embedded renal tissue was complicated by the low yield and degradation of unprotected mRNA. Suggestions for the development of this work using renal cell-culture are discussed.

Influence of impact angles on penetration rates of CRAs exposed to a high velocity multiphase flow

A combined flow loop - jet impingement pilot plant has been used to determine mass loss rates in a mixed gas - saltwater - sand multiphase flow at impact velocities up to 70 m/s. Artificial brine with a salt content of 27 g/1 was used as liquid phase. Sand content, with grain size below 150 µ, was 2.7 g/l brine. CO at a pressure of 15 bar was used as gas phase. The impact angle between jet stream (nozzle) and sample surface was varied between 30 and 90°. Rectangular stainless steel disc samples with a size of 20 × 15 × 5 mm were used. They were mechanically ground and polished prior to testing. Damaged surfaces of specimens exposed to the high velocity multiphase flow were investigated by stereo microscopy, scanning electron microscopy (SEM) and an optical device for 3D surface measurements. Furthermore, samples were investigated by applying atomic force microscopy (AFM), magnetic force microscopy (MFM) and nanoindentation. Influence of impact velocity and impact angle on penetration rates (mass loss rates) of two CRAs (UNS S30400 and N08028) are presented. Moreover effects of chemical composition and mechanical properties are critically discussed. © 2008 by NACE International.

Cadmium in the environment and high risk population groups

Cadmium has been widely used in various industries for the past fifty years, with current world production standing at around 16,755 tonnes per year. Very little cadmium is ever recycled and the ultimate fate of all cadmium is the environment. In view of reports that cadmium in the environment is increasing, this thesis aims to identify population groups 'at risk' of receiving dietary intakes of cadmium up to or above the current Food and Agricultural Organisation/World Health Organisation maximum tolerable intake of 70 ug/day. The study involves the investigation of one hundred households (260 individuals) who grow a large proportion of their vegetable diet in garden soils in the Borough of Walsall, part of an urban/industrial area in the United Kingdom. Measurements were made of the cadmium levels in atmospheric deposition, soil, house dust, diet and urine from the participants. Atmospheric deposition of cadmium was found to be comparable with other urban/industrial areas in the European Community, with deposition rates as high as 209 g ha-1 yr-1. The garden soils of the study households were found to contain up to 33 mg kg-1 total cadmium, eleven times the highest level usually found in agricultural soils. Dietary intakes of cadmium by the residents from food were calculated to be as high as 68 ug/day. It is suggested that with intakes from other sources, such as air, adventitious ingestion, smoking and occupational exposure, total intakes of cadmium may reach or exceed the FAO/WHO limit. Urinary excretion of cadmium amongst a non-smoking, non-occupationally exposed sub-group of the study population was found to be significantly higher than that of a similar urban population who did not rely on home-produced vegetables. The results from this research indicate that present levels of cadmium in urban/industrial areas can increase dietary intakes and body burdens of cadmium. As cadmium serves no useful biological function and has been found to be highly toxic, it is recommended that policy measures to reduce human exposure on the European scale be considered.

Ethanol intake of paediatric intensive care patients

Background - Limiting the amount of alcohol in children's medicines is advisable but as alcohol is the second most common solvent used in liquid preparations, paediatric patients with increased medication intake may be exposed to a considerable alcohol intake. Few medicines are specifically designed for children in Paediatric Intensive Care (PICU), and therefore adult formulations are frequently administered, with high medication use further exposing a PICU patient to undesired alcohol intake. Aims - This small pilot study aimed to examiine the intake of a sample of PICU patients, highlight common medicines used on PICU containing alcohol, provide alternatives where possible and where alternatives are not possible, provide the prescriber with a list of the higher alcohol containing medicines. Method - A retrospective medication chart review was undertaken as a two point snap shot. Data collected included age, weight, medications prescribed and the formulations used at time of the study. The patients' sedation score was recorded. The electronic medicine compendium (EMC) was consulted for any ethanol content for the commercially available products. The manufacturer was contacted for ethanol content of all ‘specials’ and any commercial products found to contain ethanol from the EMC. The PICU patient's daily intake of ethanol was calculated. The calculation was converted to an adult equivalent alcohol unit intake and although this method of conversion is crude and does not take physiological differences of adult and children into account, it was done in order to provide the clinician with commonly used terminology in deciding the risk to the patient. Results - Twenty-eight patients were prescribed a range of 69 different medications. Of the 69 medicines, 12 products were found to contain ethanol. Patient ages ranged from a 26 week premature infant to 15 years old, weights ranges from 0.7 kg to 45 kg. Only 2 out of the 28 patients did not receive ethanol containing medications, and most patients were prescribed at least two medicines containing ethanol. Daily ethanol intake uncorrected for weight ranged from 0.006 ml to 2.18 ml (median 0.26 ml). Converting this to adult units per week, alcohol intake ranged from 0.07 to 15.2 units (median 1.4 units). The two patients receiving above 15 units/week adult equivalent were prescribed an oral morphine weaning regimen, therefore the high alcohol exposure was short term. The most common drugs prescribed containing alcohol were found to be nystatin, ranitidine, furosemide and morphine. No commercially available alcohol-free oral liquid preparations were found for ranitidine, furosemide or morphine at the time of the study. Correlation of the sedation score against ethanol intake was difficult to analyse as most patients were actively sedated. Conclusions - Polypharmacy in PICU patients increases the exposure to alcohol. Some commercially available medicines provide excessive ethanol intake, providing the clinician with ethical, potentially economical dilemmas of prescribing an unlicensed medicine to minimise ethanol exposure. Further research is required to evaluate the scope of the problem, effects of exposure and provision of alcohol free formulations.

Appetite regulatory mechanisms and food intake in mice are sensitive to mismatch in diets between pregnancy and postnatal periods

Human and animal studies suggest that obesity in adulthood may have its origins partly during prenatal development. One of the underlying causes of obesity is the perturbation of hypothalamic mechanisms controlling appetite. We determined mRNA levels of genes that regulate appetite, namely neuropeptide Y (NPY), pro-opiomelanocortin (POMC) and the leptin receptor isoform Ob-Rb, in the hypothalamus of adult mouse offspring from pregnant dams fed a protein-restricted diet, and examined whether mismatched post-weaning high-fat diet altered further expression of these gene transcripts. Pregnant MF1 mice were fed either normal protein (C, 18% casein) or protein-restricted (PR, 9% casein) diet throughout pregnancy. Weaned offspring were fed to adulthood a high-fat (HF; 45% kcal fat) or standard chow (21% kcal fat) diet to generate the C/HF, C/C, PR/HF and PR/C groups. Food intake and body weight were monitored during this period. Hypothalamic tissues were collected at 16 weeks of age for analysis of gene expression by real time RT-PCR. All HF-fed offspring were observed to be heavier vs. C groups regardless of the maternal diet during pregnancy. In the PR/HF males, but not in females, daily energy intake was reduced by 20% vs. the PR/C group (p <0.001). In PR/HF males, hypothalamic mRNA levels were lower vs. the PR/C group for NPY (p <0.001) and Ob-Rb (p <0.05). POMC levels were similar in all groups. In females, mRNA levels for these transcripts were similar in all groups. Our results suggest that adaptive changes during prenatal development in response to maternal dietary manipulation may have long-term sex-specific consequences on the regulation of appetite and metabolism following post-weaning exposure to an energy-rich nutritional environment. © 2008 Elsevier B.V. All rights reserved.

The effect of frequency and microstructure on corrosion fatigue crack propagation in high strength aluminium alloys

Fatigue crack growth in high strength aluminium alloy 7150 commercial plate material has been studied in both laboratory air and acidified aqueous salt solution. The aggressive aqueous environment enhanced fatigue crack growth rates by up to an order in magnitude compared to laboratory air. The enhancement in fatigue crack growth rate was accompanied by evidence of embrittlement in the crack path, involving both brittle intergranular and transgranular failure modes. Both the enhancement of fatigue crack growth rates and the extent of intergranular growth modes are dependent on cyclic frequency which, along with the absence of a similar frequency effect in a spray-formed version of the material with a significantly different grain structure, supports a mechanism of grain boundary hydrogen diffusion for intergranular corrosion fatigue crack growth. The convergence of corrosion fatigue crack growth rates at high ΔK in both spray-formed and conventional plate materials coincides with the operation of identical transgranular corrosion fatigue modes dependent on strain-controlled hydrogen diffusion ahead of the crack tip. © 1997 Acta Metallurgica Inc.

Molecular mechanisms of salt effects on carbon nanotube dispersions in an organic solvent (N-methyl-2-pyrrolidone)

We consider the effects of salt (sodium iodide) on pristine carbon nanotube (CNT) dispersions in an organic solvent, N-methyl-2-pyrrolidone (NMP). We investigate the molecular-scale mechanisms of ion interactions with the nanotube surface and we show how the microscopic ion-surface interactions affect the stability of CNT dispersions in NMP. In our study we use a combination of fully atomistic Molecular Dynamics simulations of sodium and iodide ions at the CNT-NMP interface with direct experiments on the CNT dispersions. In the experiments we analyze the effects of salt on the stability of the dispersions by photoluminescence (PL) and optical absorption spectroscopy of the samples as well as by visual inspection. By fully atomistic Molecular Dynamics simulations we investigate the molecular-scale mechanisms of sodium and iodide ion interactions with the nanotube surface. Our simulations reveal that both ions are depleted from the CNT surface in the CNT-NMP dispersions mainly due to the two reasons: (1) there is a high energy penalty for the ion partial desolvation at the CNT surface; (2) NMP molecules form a dense solvation layer at the CNT surface that prevents ions to come close to the CNT surface. As a result, an increase of the salt concentration increases the "osmotic" stress in the CNT-NMP system and, thus, decreases the stability of the CNT dispersions in NMP. Direct experiments confirm the simulation results: addition of NaI salt into the NMP dispersions of pristine CNTs leads to precipitation of CNTs (bundle formation) even at very small salt concentration (∼10 -3 mol L -1). In line with the simulation predictions, the effect increases with the increase of the salt concentration. Overall, our results show that dissolved salt ions have strong effects on the stability of CNT dispersions. Therefore, it is possible to stimulate the bundle formation in the CNT-NMP dispersions and regulate the overall concentration of nanotubes in the dispersions by changing the NaI concentration in the solvent. © 2012 The Royal Society of Chemistry.