The development of a modified dissolution method suitable for investigating powder mixtures

A novel dissolution method was developed, suitable for powder mixtures, based on the USP basket apparatus. The baskets were modified such that the powder mixtures were retained within the baskets and not dispersed, a potential difficulty that may arise when using conventional USP basket and paddle apparatus. The advantages of this method were that the components of the mixtures were maintained in close proximity, maximizing any drug:excipient interaction and leading to more linear dissolution profiles. Two weakly acidic model drugs, ibuprofen and acetaminophen, and a selection of pharmaceutical excipients, including potential dissolution-enhancing alkalizing agents, were chosen for investigation. Dissolution profiles were obtained for simple physical mixtures. The f1 fit factor values, calculated using pure drug as the reference material, demonstrated a trend in line with expectations, with several dissolution enhancers apparent for both drugs. Also, the dissolution rates were linear over substantial parts of the profiles. For both drugs, a rank order comparison between the f1 fit factor and calculated dissolution rate, obtained from the linear section of the dissolution profile, demonstrated a correlation using a significance level of P=0.05. The method was proven to be suitable for discriminating between the effects of excipients on the dissolution of the model drugs. The method design produced dissolution profiles where the dissolution rate was linear for a substantial time, allowing determination of the dissolution rate without mathematical transformation of the data. This method may be suitable as a preliminary excipient-screening tool in the drug formulation development process.

Compressed orally disintegrating tablets:excipients evolution and formulation strategies

Introduction: Orally disintegrating tablets (ODTs) have emerged as one of the novel solid oral dosage forms with a potential to deliver a wide range of drug candidates to both paediatric and geriatric patient populations. Of the plethora of available technologies, compression of excipients offers a cost-effective and translatable methodology for the manufacture of ODTs. Areas covered: The review is a modest endeavour from the authors to assemble literature published over the last couple of decades on formulation development of compressed ODT. It describes the main ODT excipients used since the introduction of this dosage form in the 1990s and explores the switch from cellulose-based excipients towards sugar/polyols. Furthermore, it unfolds the key properties of ODT fillers, binders and disintegrants with an emphasis on their advantages and drawbacks. The review also provides a critical assessment of the various strategies employed for performance enhancement of compressed ODT with a focus on the underlying mechanisms for fast disintegration and acceptable mechanical strength. Expert opinion: Recent increase in the total number of compression-based technologies for ODT development promises to reduce the manufacturing cost of this dosage form in the future. However, some of the developed methods may affect the stability of tablets due to susceptibility to moisture, collapse of pores or the generation of less stable polymorphs which require rigorous testing prior to commercialization. © 2013 Informa UK, Ltd.

Strategic development and physicochemical analysis of oral preparations for unstable drugs

Oral liquid formulations are ideal dosage forms for paediatric, geriatric and patient with dysphagia. Dysphagia is prominent among patients suffering from stroke, motor neurone disease, advanced Alzheimer’s and Parkinson’s disease. However oral liquid preparations are particularly difficult to formulate for hydrophobic and unstable drugs. Therefore current methods employed in solving this issue include the use of ‘specials’ or extemporaneous preparations. In order to challenge this, the government has encouraged research into the field of oral liquid formulations, with the EMEA and MHRA publishing list of drugs of interest. The current work investigates strategic formulation development and characterisation of select API’s (captopril, gliclazide, melatonin, L-arginine and lansoprazole), each with unique obstacles to overcome during solubilisation, stabilisation and when developing a palatable dosage from. By preparing a validated calibration protocol for each of the drug candidates, the oral liquid formulations were assessed for stability, according to the ICH guidelines along with thorough physiochemical characterisation. The results showed that pH and polarity of the solvent had the greatest influence on the extent of drug solubilisation, with inclusion of antioxidants and molecular steric hindrance influencing the extent of drug stability. Captopril, a hydrophilic ACE inhibitor (160 mg.mL-1), undergoes dimerisation with another captopril molecule. It was found that with the addition of EDTA and HP-β-CD, the drug molecule was stabilised and prevented from initiating a thiol induced first order free radical oxidation. The cyclodextrin provided further steric hindrance (1:1 molar ratio) resulting in complete reduction of the intensity of sulphur like smell associated with captopril. Palatability is a crucial factor in patient compliance, particularly when developing a dosage form targeted towards paediatrics. L-arginine is extremely bitter in solution (148.7 g.L-1). The addition of tartaric acid into the 100 mg.mL-1 formulation was sufficient to mask the bitterness associated with its guanidium ions. The hydrophobicity of gliclazide (55 mg.L-1) was strategically challenged using a binary system of a co-solvent and surfactant to reduce the polarity of the medium and ultimately increase the solubility of the drug. A second simpler method was developed using pH modification with L-arginine. Melatonin has two major obstacles in formulation: solubility (100 μg.mL-1) and photosensitivity, which were both overcome by lowering the dielectric constant of the medium and by reversibly binding the drug within the cyclodextrin cup (1:1 ratio). The cyclodextrin acts by preventing UV rays from reaching the drug molecule and initiated the degradation pathway. Lansoprazole is an acid labile drug that could only be delivered orally via a delivery vehicle. In oral liquid preparations this involved nanoparticulate vesicles. The extent of drug loading was found to be influenced by the type of polymer, concentration of polymer, and the molecular weight. All of the formulations achieved relatively long shelf-lives with good preservative efficacy.

Paediatric drug development:reformulation, in vitro, genomic and in vivo evaluation

Angiotensin converting enzyme (ACE) inhibitors lisinopril and ramipril were selected from EMA/480197/2010 and the potassium-sparing diuretic spironolactone was selected from the NHS specials list for November 2011 drug tariff with the view to produce oral liquid formulations providing dosage forms targeting paediatrics. Lisinopril, ramipril and spironolactone were chosen for their interaction with transporter proteins in the small intestine. Formulation limitations such as poor solubility or pH sensitivity needed consideration. Lisinopril was formulated without extensive development as drug and excipients were water soluble. Ramipril and spironolactone are both insoluble in water and strategies combating this were employed. Ramipril was successfully solubilised using low concentrations of acetic acid in a co-solvent system and also via complexation with hydroxypropyl-β-cyclodextrin. A ramipril suspension was produced to take formulation development in a third direction. Spironolactone dosages were too high for solubilisation techniques to be effective so suspensions were developed. A buffer controlled pH for the sensitive drug whilst a precisely balanced surfactant and suspending agent mix provided excellent physical stability. Characterisation, stability profiling and permeability assessment were performed following formulation development. The formulation process highlighted current shortcomings in techniques for taste assessment of pharmaceutical preparations resulting in early stage research into a novel in vitro cell based assay. The formulations developed in the initial phase of the research were used as model formulations investigating microarray application in an in vitro-in vivo correlation for carrier mediated drug absorption. Caco-2 cells were assessed following transport studies for changes in genetic expression of the ATP-binding cassette and solute carrier transporter superfamilies. Findings of which were compared to in vitro and in vivo permeability findings. It was not possible to ascertain a correlation between in vivo drug absorption and the expression of individual genes or even gene families, however there was a correlation (R2 = 0.9934) between the total number of genes with significantly changed expression levels and the predicted human absorption.

Paediatric drug development of ramipril:reformulation, in vitro and in vivo evaluation

Ramipril is used mainly for the treatment of hypertension and to reduce incidence of fatality following heart attacks in patients who develop indications of congestive heart failure. In the paediatric population it is used most commonly for the treatment of heart failure, hypertension in type 1 diabetes and diabetic nephropathy. Due to the lack of a suitable liquid formulation, the current study evaluates the development of a range of oral liquid formulations of ramipril along with their in vitro and in vivo absorption studies. Three different formulation development approaches were studied: solubilisation using acetic acid as a co-solvent, complexation with hydroxypropyl-β-cyclodextrin (HP-β-CD) and suspension development using xanthan gum. Systematic optimisation of formulation parameters for the different strategies resulted in the development of products stable for twelve months at long term stability conditions. In vivo evaluation showed CMAX of 10.48 µg/mL for co-solvent, 13.04µg/ml for the suspension and 29.58µg/mL for the cyclodextrin based ramipril solution. Interestingly, both ramipril solution (co-solvent) and the suspension showed a TMAX of 2.5h, however, cyclodextrin based ramipril produced TMAX at 0.75h following administration. The results presented in this study provide translatable products for oral liquid ramipril which offer preferential paediatric use over existing alternatives.

Excipients in medicines for children:scientific and regulatory paradigms

There is an ongoing debate over the use of pharmaceutical excipients in medicines for children, triggered by the increased number of formulations suitable for this target patient population. Pharmaceutical excipients can be regarded as essential / necessary enablers in formulation development. These are materials other than the 'active pharmaceutical ingredient' which are added to the formulation to achieve a specific function1. This may include aiding in the processing or manufacture of the drug delivery system such as lubricants or flow aids, controlling the release of the active ingredient to achieve modified release, enhance patient acceptability by improving taste of medicines or to develop easily swallowed dosage forms.

The role of formulation excipients in the development of lyophilised fast-disintegrating tablets

Despite recent Success, many fast-disintegrating tablets (FDTs) still face problems of low mechanical strength, poor mouth-feel and higher disintegration times. This Study aimed to optimise FDTS using a progressive three-stage approach. A series of hardness, fracturability and disintegration time tests were performed on the formulations at each stage. During Stage 1, tablets were prepared in concentrations between 2% and 5% w/w, and were formulated at each concentration as single and combination bloom strength gelatin (BSG) using 75 and 225 BSGs. Analysis revealed that both hardness and disintegration time increased with an increase in gelatin concentration. A combination (5% gelatin) FDT comprising a 50:50 ratio of 75:225 BSGs (hardness: 13.7 +/- 0.9 N and disintegration time: 24.1 +/- 0.6 s) was judged the most ideal, and was carried forward to Stage II: the addition of the saccharides sorbitol, mannitol and sucrose in concentrations between 10% and 80% w/w. The best properties were exhibited by mannitol-containing formulations (50%-hardness: 30.9 +/- 2.8 N and disintegration time: 13.3 +/- 2.1 s), which were carried forward to the next stage: the addition of viscosity-modifying polymers to improve mouth-feel and aid pre-gastric retention. Addition of carbopol 974P-NF resulted in the enhancement of viscosity with a compromise of the hardness of the tablet, whereas Pluronic F127 (6%) showed an increase in disintegration time and viscosity with retention of mechanical propel-ties. (C) 2008 Elsevier B.V. All rights reserved.

Development and formulation of wax-based transdermal drug delivery systems

Topical and transdermal formulations are promising platforms for the delivery of drugs. A unit dose topical or transdermal drug delivery system that optimises the solubility of drugs within the vehicle provides a novel dosage form for efficacious delivery that also offers a simple manufacture technique is desirable. This study used Witepsol® H15 wax as a abase for the delivery system. One aspect of this project involved determination of the solubility of ibuprofen, flurbiprofen and naproxen in the was using microscopy, Higuchi release kinetics, HyperDSC and mathematical modelling techniques. Correlations between the results obtained via these techniques were noted with additional merits such as provision of valuable information on drug release kinetics and possible interactions between the drug and excipients. A second aspect of this project involved the incorporation of additional excipients: Tween 20 (T), Carbopol®971 (C) and menthol (M) to the wax formulation. On in vitro permeation through porcine skin, the preferred formulations were: ibuprofen (5% w/w) within Witepsol®H15 + 1% w/w T; flurbiprofen (10% w/w) within Witepsol®H15 + 1% w/w T; naproxen (5% w/w) within Witepsol®H15 + 1% w/w T + 1% C and sodium diclofenac (10% w/w) within Witepsol®H15 + 1% w/w T + 1% w/w T + 1% w/w C + 5% w/w M. Unit dose transdermal tablets containing ibuprofen and diclofenac were produced with improved flux compared to marketed products; Voltarol Emugel® demonstrated flux of 1.68x10-3 cm/h compared to 123 x 10-3 cm/h for the optimised product as detailed above; Ibugel Forte® demonstrated a permeation coefficient value of 7.65 x 10-3 cm/h compared to 8.69 x 10-3 cm/h for the optimised product as described above.

Formulation and development of cationic liposomes as adjuvants for subunit protein vaccinese

Liposomes remain at the forefront of vaccine design due to their well documented abilities to act as delivery vehicles and adjuvants. Liposomes have been described to initiate an antigen depot-effect, thereby increasing antigen exposure to circulating antigen-presenting cells. More recently, in-depth reviews have focussed on inherent immunostimulatory abilities of various cationic lipids, the use of which is consequently of interest in the development of subunit protein vaccines which when delivered without an adjuvant are poorly immunogenic. The importance of liposomes for the mediation of an antigen depot-effect was examined by use of a dual-radiolabelling technique thereby allowing simultaneous detection of liposomal and antigenic components and analysis of their pharmacokinetic profile. In addition to investigating the biodistribution of these formulations, their physicochemical properties were analysed and the ability of the various liposome formulations to elicit humoral and cell-mediated immune responses was investigated. Our results show a requirement of cationic charge and medium/strong levels of antigen adsorption to the cationic liposome in order for both a liposome and antigen depot-effect to occur at the injection site. The choice of injection route had little effect on the pharmacokinetics or immunogenicity observed. In vitro, cationic liposomes were more cytotoxic than neutral liposomes due to significantly enhanced levels of cell uptake. With regards to the role of bilayer fluidity, liposomes expressing more rigid bilayers displayed increased retention at the injection site although this did not necessarily result in increased antigen retention. Furthermore, liposome bilayer rigidity did not necessarily correlate with improved immunogenicity. In similar findings, liposome size did not appear to control liposome or antigen retention at the injection site. However, a strong liposome size correlation between splenocyte proliferation and production of IL-10 was noted; specifically immunisation with large liposomes lead to increased levels of splenocyte proliferation coupled with decreased IL-10 production.

Novel formulation strategies for the fabrication of lyophilised orally disintegrating tablets

Orally disintegrating Tablets (ODTs), also known as fast-disintegrating, fast-melt or fast-dissolving tablets, are a relatively novel dosage technology that involves the rapid disintegration or dissolution of the dosage form into a solution or suspension in the mouth without the need for water. The solution containing the active ingredients is swallowed, and the active ingredients are then absorbed through the gastrointestinal epithelium to reach the target and produce the desired effect. Formulation of ODTs was originally developed to address swallowing difficulties of conventional solid oral dosage forms (tablets and capsules) experienced by wide range of patient population, especially children and elderly. The current work investigates the formulation and development of ODTs prepared by freeze drying. Initial studies focused on formulation parameters that influence the manufacturing process and performance of lyophilised tablets based on excipients used in commercial products (gelatin and saccharides). The second phase of the work was followed up by comprehensive studies to address the essential need to create saccharide free ODTs using naturally accruing amino acids individually or in combinations. Furthermore, a factorial design study was carried out to investigate the feasibility of delivering multiparticulate systems of challenging drugs using a novel formulation that exploited the electrostatic associative interaction between gelatin and carrageenan. Finally, studies aimed to replace gelatin with ethically and morally accepted components to the end users were performed and the selected binder was used in factorial design studies to investigate and optimise ODT formulations that incorporated drugs with varies physicochemical properties. Our results show that formulation of elegant lyophilised ODTs with instant disintegration and adequate mechanical strength requires carful optimisation of gelatin concentration and bloom strength in addition to saccharide type and concentration. Successful formulation of saccharides free lyophilised ODTs requires amino acids that crystallise in the frozen state or display relatively high Tg', interact and integrate completely with the binder and, also, display short wetting time with the disintegrating medium. The use of an optimised mixture of gelatin, carrageenan and alanine was able to create viscous solutions to suspend multiparticulate systems and at the same time provide tablets with short disintegration times and adequate mechanical properties. On the other hand, gum arabic showed an outstanding potential for use as a binder in the formulation of lyophilised ODTs. Compared to gelatin formulations, the use of gum arabic simplified the formulation stages, shortened the freeze drying cycles and produced tablets with superior performance in terms of the disintegration time and mechanical strength. Furthermore, formulation of lyophilised ODTs based on gum arabic showed capability to deliver diverse range of drugs with advantages over commercial products.

Development and evaluation of a novel intranasal spray for the delivery of amantadine

The aim of this study was to develop and characterize an intranasal delivery system for amantadine hydrochloride (AMT). Optimal formulations consisted of a thermosensitive polymer Pluronic® 127 and either carboxymethyl cellulose or chitosan which demonstrated gel transition at nasal cavity temperatures (34 ± 1°C). Rheologically, the loss tangent (Tan δ) confirmed a 3-stage gelation phenomena at 34 ± 1°C and non-Newtonian behavior. Storage of optimized formulation carboxymethyl cellulose and optimal formulation chitosan at 4°C for 8 weeks resulted in repeatable release profiles at 34°C when sampled, with a Fickian mechanism earlier on but moving toward anomalous transport by week 8. Polymers (Pluronic® 127, carboxymethyl cellulose, and chitosan) demonstrated no significant cellular toxicity to human nasal epithelial cells up to 4 mg/mL and up to 1 mM for AMT (IC50: 4.5 ± 0.05 mM). Optimized formulation carboxymethyl cellulose and optimal formulation chitosan demonstrated slower release across an in vitro human nasal airway model (43%-44% vs 79 ± 4.58% for AMT). Using a human nasal cast model, deposition into the olfactory regions (potential nose-to-brain) was demonstrated on nozzle insertion (5 mm), whereas tilting of the head forward (15°) resulted in greater deposition in the bulk of the nasal cavity.

Regional benchmarking in a global context:knowledge, competitiveness, and economic development

Benchmarking exercises have become increasingly popular within the sphere of regional policy making. However, most exercises are restricted to comparing regions within a particular continental bloc or nation.This article introduces the World Knowledge Competitiveness Index (WKCI), which is one of the very few benchmarking exercises established to compare regions across continents.The article discusses the formulation of the WKCI and analyzes the results of the most recent editions.The results suggest that there are significant variations in the knowledge-based regional economic development models at work across the globe. Further analysis also indicates that Silicon Valley, as the highest ranked WKCI region, holds a unique economic position among the globe’s leading regions. However, significant changes in the sources of regional competitiveness are evolving as a result of the emergence of new regional hot spots in Asia. It is concluded that benchmarking is imperative to the learning process of regional policy making.

Increased potential of a cationic liposome-based delivery system:enhancing stability and sustained immunological activity in pre-clinical development

The combination of dimethyl dioctadecyl ammonium bromide (DDA) and the synthetic cord factor trehalose dibehenate (TDB) with Ag85B-ESAT-6 (H1 fusion protein) has been found to promote strong protective immune responses against Mycobacterium tuberculosis. The development of a vaccine formulation that is able to facilitate the requirements of sterility, stability and generation of a vaccine product with acceptable composition, shelf-life and safety profile may necessitate selected alterations in vaccine formulation. This study describes the implementation of a sterilisation protocol and the use of selected lyoprotective agents in order to fulfil these requirements. Concomitantly, close analysis of any alteration in physico-chemical characteristics and parameters of immunogenicity have been examined for this promising DDA liposome-based tuberculosis vaccine. The study addresses the extensive guidelines on parameters for non-clinical assessment, suitable for liposomal vaccines and other vaccine delivery systems issued by the World Health Organisation (WHO) and the European Medicines Agency (EMEA). Physical and chemical stability was observed following alteration in formulations to include novel cryoprotectants and radiation sterilisation. Immunogenicity was maintained following these alterations and even improved by modification with lysine as the cryoprotective agent for sterilised formulations. Taken together, these results outline the successful alteration to a liposomal vaccine, representing improved formulations by rational modification, whilst maintaining biological activity.

A study of strategy formulation in an automotive manufacturer

The strategies and operations of the Rover Group were investigated using a behaviour based longitudinal examination. The investigating method used was developed from Mintzberg's classical diachronic study approach through the adoption of an observing participant approach supplemented with probes into specific areas of the organisation's activities. The thesis argues, through the use of a future-forward perspective of organisation capability, that an organisation's future capability can be assessed. The thesis questions the periodisation approach normally adopted in longitudinal studies and proposes an alternative method which the author believes generates a better understanding of the operations and future potential of the organisation. This method also produces generalisations which can be readily applied to other organisations. The introduction of a process perspective to behavioural studies has led to the promise of a unified understanding of strategic management and organisation development.