Atom transfer radical polymerisation - towards the synthesis of a fully-functional photorefractive polymer

Atom transfer radical polymerisation (ATRP) of styrene in xylene solution initiated with 1-phenylethyl bromide and mediated by CuBr/N-propyl-2- pyridinemethanimine catalyst complex was studied. The polymerisation was ill-controlled, yielding polymers with broad molecular weight distributions and values of number average molecular weight considerably higher than the theoretical values calculated from 100% initiator efficiency. The degree of control afforded over the polymerisation was enhanced by use of a more soluble catalyst complex, CuBr/N-octyl-2-pyridinemethanimine. Furthermore, the use of a more polar solvent, diglyme, generated a homogeneous catalyst complex that facilitated the production of polymers having narrow molecular weight distributions (1.10 < PDi < 1.20). The kinetics of the atom transfer radical polymerisation of methyl methacrylate at 90°C in diglyme solution initiated with ethyl-2-bromoisobutyrate and mediated by CuBr/N-octyl-2-pyridinemethanimine was studied and the orders of the reaction were established. The effect on the rate of polymerisation of the ratio of CuBr:N-octyl-2-pyridinemethanimine was also determined. The temperature dependencies of the rate of polymerisation of methyl methacrylate in diglyme solution and xylene solution were studied, and were found to be non-linear and dependent upon the polarity of the solvent. The use of highly polar aprotic solvents, such as N,N-dimethylformamide and dimethylsulphoxide, was found to be detrimental to the degree of control afforded over the polymerisation of methyl methacrylate. This was circumvented by use of a 5-fold excess, over that conventionally used, of catalyst complex. The atom transfer radical polymerisation of (4-nitrophenyl)-[3-[N-[2- (methacryloyloxy)ethyl]carbazolyl]]diazene in dimethyl sulphoxide solution was studied. Although homopolymerisation yielded only oligomers, copolymerisation of this monomer with methyl methacrylate was found to be readily achievable. Keywords: ATRP, Styrene; Methyl methacrylate; Polar solvents; Fully-functional photorefractive polymer. 2

Synthesis and characterization of triazolotriazines

The Dimroth rearrangement in ring-fused 1,2,4-triazoles has been reviewed in detail in Part I and the synthesis of all known triazolo-triazines is described in Part II. Experimental investigations concerned the establishinent of the skeletal arrangement of a variety of triazolotriazines formed by several synthetic routes. Interaction of 3-amino-5-hydrazino-12,4-triazole and benzilafforded 2-amino-6, 7-diphenyl-1, 2,4-triazolo[ 5, 1-c-]-1,2,4-triazine,whereas cyclization of 5,6-diphenyl-3-hydrazino-1,2,4-triazine withcyanogen bromide resulted in the isomeric 3-amino-6,7-diphenyl,-1,2,4-triazolo [4, 3-b]-1,2,4-triazine: both amines were deaminated with amyl nitrite in boiling tetrahydrofuran without rearrangement of the heterocyclic skeleton. 6,7-Diphenyl-1,2,4-triazolo[5,1-cJ-1,2.4-triazine, synthesized from 3-hydrazino-1,2,4-triazole and benzil, formed a covalent hydrate which could be detected spectroscopically in solution, and a covalemt methanolate and ethanolate which could be isolated. A new route to 3-amino-5-hydrazino-pyrazole is described and cyclization to 7-amino-3,4-diphenyl-pyrazolo[ 5,1-.c]-1,2,4-triazine was achieved with benzil. The diazonium nitrate of 3-amino-1,2,4-triazole coupled with ethyl cyanoacetate to yield a mixture of two geometrical isomers of ethyl 2-(2H-1,2,4-triazol-3-ylhydrazono) cyanoacetate.Recrystallization of the crude coupling mixture from aqueous ethanol gave a single hydra-zone which cyclized predominantly to ethyl 7-amino-1,2,4-triazolo[5,1-c]-1,2,4-triazine-6-carboxylate in acid conditions and 6-cyano-1,2,4-triazolo[ 5,1-c]-1,2,4~triazin-7(4H)-one under basic conditions. The nature of the cyclizing medium also controlled the cyclization of .the (pyrazol-ylhydrazono) cyanoacetate hut the corresponding (tetrazol- ylhydrazono) cyanoacetate gave only ethyl 7-aminotetrazolo[ 5,1-cJ-1,2,4- -triazine-6-carboxylate. 2-( 2H-1,2,4-Triazol-3-:ylhydrazono) malonitrile cyclized unambiguously to 7-amino-6-cyano-1,2,4-triazolo-[ 5,1-c]-1,2,4- triazine. Drastic hydrolysis of ethyl 2-(2H-1,2,4-triazol-3-yllhydrazono)-cyanoacetate, ethyl 7-amino-1, 2,4-triazolo[ 5,1-c]-1,2,4-triazine-6-carboxylate, 6-cyano-1,2,4-triazolo[ 5,1-c]-1,2,4-triazin-7{ 4H)-one and 7-amino-6- cyano-1,2,4-triazolo[5,1-c]-1,2,4-triazine gave a hydrate of 1,2,4-triazo1o[5,1-c ]-1,2,4-triazin-7(4H)-one. Mass spectral fragmentations of 7-aminoazolo-[5,1-c]-1,2,4-triazinesconfirm that the azole ring is more stable than the 1,2,4-triazine ring on electron impact.

Controlled growth of poly(2-(diethylamino)ethyl methacrylate) brushes via atom transfer radical polymerisation on planar silicon surfaces

Progress in making pH-responsive polyelectrolyte brushes with a range of different grafting densities is reported. Polymer brushes of poly(2-(diethylamino)ethyl methacrylate) were synthesised via atom transfer radical polymerisation on silicon wafers using a 'grafted from' approach. The [11-(2-bromo-2-methyl) propionyloxy]undecyl trichlorosilane initiator was covalently attached to the silicon via silylation, from which the brushes were grown using a catalytic system of copper(I) chloride and pentamethyldiethylenetriamine in tetrahydrofuran at 80°C. X-ray reflectivity was used to assess the initiator surfaces and an upper limit on the grafting density of the polymer was determined. The quality of the brushes produced was analysed using ellipsometry and atomic force microscopy, which is also discussed.