Synthesis and characterization of triazolotriazines

The Dimroth rearrangement in ring-fused 1,2,4-triazoles has been reviewed in detail in Part I and the synthesis of all known triazolo-triazines is described in Part II. Experimental investigations concerned the establishinent of the skeletal arrangement of a variety of triazolotriazines formed by several synthetic routes. Interaction of 3-amino-5-hydrazino-12,4-triazole and benzilafforded 2-amino-6, 7-diphenyl-1, 2,4-triazolo[ 5, 1-c-]-1,2,4-triazine,whereas cyclization of 5,6-diphenyl-3-hydrazino-1,2,4-triazine withcyanogen bromide resulted in the isomeric 3-amino-6,7-diphenyl,-1,2,4-triazolo [4, 3-b]-1,2,4-triazine: both amines were deaminated with amyl nitrite in boiling tetrahydrofuran without rearrangement of the heterocyclic skeleton. 6,7-Diphenyl-1,2,4-triazolo[5,1-cJ-1,2.4-triazine, synthesized from 3-hydrazino-1,2,4-triazole and benzil, formed a covalent hydrate which could be detected spectroscopically in solution, and a covalemt methanolate and ethanolate which could be isolated. A new route to 3-amino-5-hydrazino-pyrazole is described and cyclization to 7-amino-3,4-diphenyl-pyrazolo[ 5,1-.c]-1,2,4-triazine was achieved with benzil. The diazonium nitrate of 3-amino-1,2,4-triazole coupled with ethyl cyanoacetate to yield a mixture of two geometrical isomers of ethyl 2-(2H-1,2,4-triazol-3-ylhydrazono) cyanoacetate.Recrystallization of the crude coupling mixture from aqueous ethanol gave a single hydra-zone which cyclized predominantly to ethyl 7-amino-1,2,4-triazolo[5,1-c]-1,2,4-triazine-6-carboxylate in acid conditions and 6-cyano-1,2,4-triazolo[ 5,1-c]-1,2,4~triazin-7(4H)-one under basic conditions. The nature of the cyclizing medium also controlled the cyclization of .the (pyrazol-ylhydrazono) cyanoacetate hut the corresponding (tetrazol- ylhydrazono) cyanoacetate gave only ethyl 7-aminotetrazolo[ 5,1-cJ-1,2,4- -triazine-6-carboxylate. 2-( 2H-1,2,4-Triazol-3-:ylhydrazono) malonitrile cyclized unambiguously to 7-amino-6-cyano-1,2,4-triazolo-[ 5,1-c]-1,2,4- triazine. Drastic hydrolysis of ethyl 2-(2H-1,2,4-triazol-3-yllhydrazono)-cyanoacetate, ethyl 7-amino-1, 2,4-triazolo[ 5,1-c]-1,2,4-triazine-6-carboxylate, 6-cyano-1,2,4-triazolo[ 5,1-c]-1,2,4-triazin-7{ 4H)-one and 7-amino-6- cyano-1,2,4-triazolo[5,1-c]-1,2,4-triazine gave a hydrate of 1,2,4-triazo1o[5,1-c ]-1,2,4-triazin-7(4H)-one. Mass spectral fragmentations of 7-aminoazolo-[5,1-c]-1,2,4-triazinesconfirm that the azole ring is more stable than the 1,2,4-triazine ring on electron impact.

A detailed study of the mechanical and electrical aspects of microparticle impact phenomena

An experimental and theoretical study of the impact behaviour of charged microparticles in a high voltage vacuum gap has been carried out to investigate under controlled conditions the role of low velocity microparticles (ζ 500 ms-1) in initiating electrical breakdown in such gaps. This has involved developing a unique (UHV) low-velocity source of micron-sized charged particles to study the underlying mechanical and electrical aspects of micro-particle impact on a range of target materials e.g. Pb, Ti, C, stainless-steel and mica etc., having atomically clean or oxidised surfaces. Argon-ion etching and electron-beam heating has been used for in-situ surface treatment and ellipsometry for characterising the target surfaces. An associated sphere/plane theoretical model has been developed for detailed analysis of the many complex electrical (in-flight in-field emission, M.I.M. tunnelling and ohmic conduction) and mechanical (impact dynamics, deformation and heating) phenomena that are involved when a microparticle closely approaches and impacts on a plane target. In each instance the influence of parameters such as particle radius, particle/target impact velocity, surface field, surface condition and material has been determined.

Influence of impact angles on penetration rates of CRAs exposed to a high velocity multiphase flow

A combined flow loop - jet impingement pilot plant has been used to determine mass loss rates in a mixed gas - saltwater - sand multiphase flow at impact velocities up to 70 m/s. Artificial brine with a salt content of 27 g/1 was used as liquid phase. Sand content, with grain size below 150 µ, was 2.7 g/l brine. CO at a pressure of 15 bar was used as gas phase. The impact angle between jet stream (nozzle) and sample surface was varied between 30 and 90°. Rectangular stainless steel disc samples with a size of 20 × 15 × 5 mm were used. They were mechanically ground and polished prior to testing. Damaged surfaces of specimens exposed to the high velocity multiphase flow were investigated by stereo microscopy, scanning electron microscopy (SEM) and an optical device for 3D surface measurements. Furthermore, samples were investigated by applying atomic force microscopy (AFM), magnetic force microscopy (MFM) and nanoindentation. Influence of impact velocity and impact angle on penetration rates (mass loss rates) of two CRAs (UNS S30400 and N08028) are presented. Moreover effects of chemical composition and mechanical properties are critically discussed. © 2008 by NACE International.

Impact of co-adsorbed oxygen on crotonaldehyde adsorption over gold nanoclusters:a computational study

Crotonaldehyde (2-butenal) adsorption over gold sub-nanometer particles, and the influence of co-adsorbed oxygen, has been systematically investigated by computational methods. Using density functional theory, the adsorption energetics of crotonaldehyde on bare and oxidised gold clusters (Au , d = 0.8 nm) were determined as a function of oxygen coverage and coordination geometry. At low oxygen coverage, sites are available for which crotonaldehyde adsorption is enhanced relative to bare Au clusters by 10 kJ mol. At higher oxygen coverage, crotonaldehyde is forced to adsorb in close proximity to oxygen weakening adsorption by up to 60 kJ mol relative to bare Au. Bonding geometries, density of states plots and Bader analysis, are used to elucidate crotonaldehyde bonding to gold nanoparticles in terms of partial electron transfer from Au to crotonaldehyde, and note that donation to gold from crotonaldehyde also becomes significant following metal oxidation. At high oxygen coverage we find that all molecular adsorption sites have a neighbouring, destabilising, oxygen adatom so that despite enhanced donation, crotonaldehyde adsorption is always weakened by steric interactions. For a larger cluster (Au, d = 1.1 nm) crotonaldehyde adsorption is destabilized in this way even at a low oxygen coverage. These findings provide a quantitative framework to underpin the experimentally observed influence of oxygen on the selective oxidation of crotyl alcohol to crotonaldehyde over gold and gold-palladium alloys. © 2014 the Partner Organisations.

Microparticle surface layering through dry coating:impact of moisture content and process parameters on the properties of orally disintegrating tablets

OBJECTIVES: The aim of this study was to investigate the influence of process parameters during dry coating on particle and dosage form properties upon varying the surface adsorbed moisture of microcrystalline cellulose (MCC), a model filler/binder for orally disintegrating tablets (ODTs). METHODS: The moisture content of MCC was optimised using the spray water method and analysed using thermogravimetric analysis. Microproperty/macroproperty assessment was investigated using atomic force microscopy, nano-indentation, scanning electron microscopy, tablet hardness and disintegration testing. KEY FINDINGS: The results showed that MCC demonstrated its best flowability at a moisture content of 11.2% w/w when compared to control, comprising of 3.9% w/w moisture. The use of the composite powder coating process (without air) resulted in up to 80% increase in tablet hardness, when compared to the control. The study also demonstrated that surface adsorbed moisture can be displaced upon addition of excipients during dry processing circumventing the need for particle drying before tabletting. CONCLUSIONS: It was concluded that MCC with a moisture content of 11% w/w provides a good balance between powder flowability and favourable ODT characteristics.