Kinetic study of the pyrolysis of miscanthus and its acid hydrolysis residue by thermogravimetric analysis

The kinetic parameters of the pyrolysis of miscanthus and its acid hydrolysis residue (AHR) were determined using thermogravimetric analysis (TGA). The AHR was produced at the University of Limerick by treating miscanthus with 5 wt.% sulphuric acid at 175 °C as representative of a lignocellulosic acid hydrolysis product. For the TGA experiments, 3 to 6 g of sample, milled and sieved to a particle size below 250 μm, were placed in the TGA ceramic crucible. The experiments were carried out under non-isothermal conditions heating the samples from 50 to 900 °C at heating rates of 2.5, 5, 10, 17 and 25 °C/min. The activation energy (EA) of the decomposition process was determined from the TGA data by differential analysis (Friedman) and three isoconversional methods of integral analysis (Kissinger–Akahira–Sunose, Ozawa–Flynn–Wall, Vyazovkin). The activation energy ranged from 129 to 156 kJ/mol for miscanthus and from 200 to 376 kJ/mol for AHR increasing with increasing conversion. The reaction model was selected using the non-linear least squares method and the pre-exponential factor was calculated from the Arrhenius approximation. The results showed that the best fitting reaction model was the third order reaction for both feedstocks. The pre-exponential factor was in the range of 5.6 × 1010 to 3.9 × 10+ 13 min− 1 for miscanthus and 2.1 × 1016 to 7.7 × 1025 min− 1 for AHR.

Investigating the role of capacitive coupling between the operating table and the return electrode of an electrosurgery unit in the modification of the current density distribution within the patients’ body

Background: Electrosurgery units are widely employed in modern surgery. Advances in technology have enhanced the safety of these devices, nevertheless, accidental burns are still regularly reported. This study focuses on possible causes of sacral burns as complication of the use of electrosurgery. Burns are caused by local densifications of the current, but the actual pathway of current within patient's body is unknown. Numerical electromagnetic analysis can help in understanding the issue. Methods: To this aim, an accurate heterogeneous model of human body (including seventy-seven different tissues), electrosurgery electrodes, operating table and mattress was build to resemble a typical surgery condition. The patient lays supine on the mattress with the active electrode placed onto the thorax and the return electrode on his back. Common operating frequencies of electrosurgery units were considered. Finite Difference Time Domain electromagnetic analysis was carried out to compute the spatial distribution of current density within the patient's body. A differential analysis by changing the electrical properties of the operating table from a conductor to an insulator was also performed. Results: Results revealed that distributed capacitive coupling between patient body and the conductive operating table offers an alternative path to the electrosurgery current. The patient's anatomy, the positioning and the different electromagnetic properties of tissues promote a densification of the current at the head and sacral region. In particular, high values of current density were located behind the sacral bone and beneath the skin. This did not occur in the case of non-conductive operating table. Conclusion: Results of the simulation highlight the role played from capacitive couplings between the return electrode and the conductive operating table. The concentration of current density may result in an undesired rise in temperature, originating burns in body region far from the electrodes. This outcome is concordant with the type of surgery-related sacral burns reported in literature. Such burns cannot be immediately detected after surgery, but appear later and can be confused with bedsores. In addition, the dosimetric analysis suggests that reducing the capacity coupling between the return electrode and the operating table can decrease or avoid this problem. © 2013 Bifulco et al.; licensee BioMed Central Ltd.

Differential gains from Business Link support and advice:a treatment effects approach

The provision of advisory support to small firms is almost ubiquitous in OECD countries, although it is organised in different ways and is justified on slightly different grounds. In England publicly supported advisory services are provided through the Business Link (BL) network. Here, we consider two questions: what sort of companies receive advisory support from BL; and, what types of firms benefit most from that support? Our analysis is based on a telephone survey of 2000 firms, around half of which had received intensive assistance from BL between April and October 2003. Probit analysis suggests that the probability of receiving assistance was greater among younger businesses, those with larger numbers of directors in the firm, and those with more gender diversity among the firm's leadership team. Our business-growth models suggest that BL intensive assistance was having a positive effect on employment growth in 2003. BL had a positive but insignificant impact on sales growth over the period. Employment growth effects tend to be larger where firms have a management and organisational structure, which is more conducive to absorbing and making use of external advice. The analysis suggests that BL might increase its impact through targeting these larger, more export-orientated, businesses. Employment growth effects differ little, however, depending on either the ethnic or the gender diversity of the leadership team.

Market-level information and the diffusion of competing technologies:an exploratory analysis of the LAN industry

Market-level information diffused by print media may contribute to the legitimation of an emerging technology and thus influence the diffusion of competing technological standards. After analyzing more than 10,000 trade media abstracts from the Local Area Networks (LAN) industry published between 1981 and 2000, we found the presence of differential effects on the adoption of competing standards by two market-level information types: technology and product availability. The significance of these effects depends on the technology's order of entry and suggests that high-tech product managers should make strategic use of market-level information by appropriately focusing the content of their communications. © 2007 Elsevier B.V. All rights reserved.

Identification, mutagenesis, and transcriptional analysis of the methanesulfonate transport operon of methylosulfonomonas methylovora

Recently identified genes located downstream (3') of the msmEF (transport encoding) gene cluster, msmGH, and located 5' of the structural genes for methanesulfonate monooxygenase (MSAMO) are described from Methylosulfonomonas methylovora. Sequence analysis of the derived polypeptide sequences encoded by these genes revealed a high degree of identity to ABC-type transporters. MsmE showed similarity to a putative periplasmic substrate binding protein, MsmF resembled an integral membraneassociated protein, and MsmG was a putative ATP-binding enzyme. MsmH was thought to be the cognate permease component of the sulfonate transport system. The close association of these putative transport genes to the MSAMO structural genes msmABCD suggested a role for these genes in transport of methanesulfonic acid (MSA) into M. methylovora. msmEFGH and msmABCD constituted two operons for the coordinated expression of MSAMO and the MSA transporter systems. Reverse-transcription-PCR analysis of msmABCD and msmEFGH revealed differential expression of these genes during growth on MSA and methanol. The msmEFGH operon was constitutively expressed, whereas MSA induced expression of msmABCD. A mutant defective in msmE had considerably slower growth rates than the wild type, thus supporting the proposed role of MsmE in the transport of MSA into M. methylovora.

Sequence analysis and distribution of an IS3-like insertion element isolated from Salmonella enteritidis

The nucleotide sequence of a 3 kb region immediately upstream of the sef operon of Salmonella enteritidis was determined. A 1230 base pair insertion sequence which shared sequence identity (> 75%) with members of the IS3 family was revealed. This element, designated IS1230, had almost identical (90% identity) terminal inverted repeats to Escherichia coli IS3 but unlike other IS3-like sequences lacked the two characteristic open reading frames which encode the putative transposase. S. enteritidis possessed only one copy of this insertion sequence although Southern hybridisation analysis of restriction digests of genomic DNA revealed another fragment located in a region different from the sef operon which hybridised weakly which suggested the presence of an IS1230 homologue. The distribution of IS1230 and IS1230-like elements was shown to be widespread amongst salmonellas and the patterns of restriction fragments which hybridised differed significantly between Salmonella serotypes and it is suggested that IS1230 has potential for development as a differential diagnostic tool.

Applications of differential geometry to high spin field theories

The main aim of this thesis is to investigate the application of methods of differential geometry to the constraint analysis of relativistic high spin field theories. As a starting point the coordinate dependent descriptions of the Lagrangian and Dirac-Bergmann constraint algorithms are reviewed for general second order systems. These two algorithms are then respectively employed to analyse the constraint structure of the massive spin-1 Proca field from the Lagrangian and Hamiltonian viewpoints. As an example of a coupled field theoretic system the constraint analysis of the massive Rarita-Schwinger spin-3/2 field coupled to an external electromagnetic field is then reviewed in terms of the coordinate dependent Dirac-Bergmann algorithm for first order systems. The standard Velo-Zwanziger and Johnson-Sudarshan inconsistencies that this coupled system seemingly suffers from are then discussed in light of this full constraint analysis and it is found that both these pathologies degenerate to a field-induced loss of degrees of freedom. A description of the geometrical version of the Dirac-Bergmann algorithm developed by Gotay, Nester and Hinds begins the geometrical examination of high spin field theories. This geometric constraint algorithm is then applied to the free Proca field and to two Proca field couplings; the first of which is the minimal coupling to an external electromagnetic field whilst the second is the coupling to an external symmetric tensor field. The onset of acausality in this latter coupled case is then considered in relation to the geometric constraint algorithm.

An experimental analysis of operating conditions in cold roll-forming

A detailed literature survey confirmed cold roll-forming to be a complex and little understood process. In spite of its growing value, the process remains largely un-automated with few principles used in set-up of the rolling mill. This work concentrates on experimental investigations of operating conditions in order to gain a scientific understanding of the process. The operating conditions are; inter-pass distance, roll load, roll speed, horizontal roll alignment. Fifty tests have been carried out under varied operating conditions, measuring section quality and longitudinal straining to give a picture of bending. A channel section was chosen for its simplicity and compatibility with previous work. Quality measurements were measured in terms of vertical bow, twist and cross-sectional geometric accuracy, and a complete method of classifying quality has been devised. The longitudinal strain profile was recorded, by the use of strain gauges attached to the strip surface at five locations. Parameter control is shown to be important in allowing consistency in section quality. At present rolling mills are constructed with large tolerances on operating conditions. By reduction of the variability in parameters, section consistency is maintained and mill down-time is reduced. Roll load, alignment and differential roll speed are all shown to affect quality, and can be used to control quality. Set-up time is reduced by improving the design of the mill so that parameter values can be measured and set, without the need for judgment by eye. Values of parameters can be guided by models of the process, although elements of experience are still unavoidable. Despite increased parameter control, section quality is variable, if only due to variability in strip material properties. Parameters must therefore be changed during rolling. Ideally this can take place by closed-loop feedback control. Future work lies in overcoming the problems connected with this control.

Differential perception of innovation with particular reference to the organisational context

Differential perception of innovation is a research area which has been advocated as a suitable topic for study in recent years. It developed from the problems encountered within earlier perception of innovation studies which sought to establish what characteristics of an innovation affected the ease of its adoption. While some success was achieved In relating perception of innovation to adoption behaviour, variability encountered Within groups expected - to fercelve innovation similarly suggested that the needs and experiences of the potential adopter were significantly affecting the research findings. Such analysis being supported by both sociological and psychological perceptual research. The present study sought to identify the presence of differential perception of innovation and explore the nature of the process. It was decided to base the research in an organisational context and to concentrate upon manufacturing innovation. It has been recognised that such adoption of technological innovation is commonly the product of a collective decision-making process, involving individuals from a variety of occupational backgrounds, both in terms of occupational speciality and level within the hierarchy. Such roles appeared likely to significantly influence perception of technological innovation, as gathered through an appropriate measure and were readily identifiable. Data vas collected by means of a face-to-face card presentation technique, a questionnaire and through case study material. Differential perception of innovation effects were apparent In the results, many similarities and differences of perception being related to the needs and experiences of the individuals studied. Phenomenological analysis, which recognises the total nature of experience in infiuencing behaviour, offered the best means of explaining the findings. It was also clear that the bureaucratic model of role definition was not applicable to the area studied, it seeming likely that such definitions are weaker under conditions of uncertainty, such as encountered in innovative decision-making.

Kineto-elastodynamic analysis of high-speed four-bar mechanism

This thesis addresses the kineto-elastodynamic analysis of a four-bar mechanism running at high-speed where all links are assumed to be flexible. First, the mechanism, at static configurations, is considered as structure. Two methods are used to model the system, namely the finite element method (FEM) and the dynamic stiffness method. The natural frequencies and mode shapes at different positions from both methods are calculated and compared. The FEM is used to model the mechanism running at high-speed. The governing equations of motion are derived using Hamilton's principle. The equations obtained are a set of stiff ordinary differential equations with periodic coefficients. A model is developed whereby the FEM and the dynamic stiffness method are used conjointly to provide high-precision results with only one element per link. The principal concern of the mechanism designer is the behaviour of the mechanism at steady-state. Few algorithms have been developed to deliver the steady-state solution without resorting to costly time marching simulation. In this study two algorithms are developed to overcome the limitations of the existing algorithms. The superiority of the new algorithms is demonstrated. The notion of critical speeds is clarified and a distinction is drawn between "critical speeds", where stresses are at a local maximum, and "unstable bands" where the mechanism deflections will grow boundlessly. Floquet theory is used to assess the stability of the system. A simple method to locate the critical speeds is derived. It is shown that the critical speeds of the mechanism coincide with the local maxima of the eigenvalues of the transition matrix with respect to the rotational speed of the mechanism.

Numerical and statistical analysis of long-haul undersea optical communication systems

Firstly, we numerically model a practical 20 Gb/s undersea configuration employing the Return-to-Zero Differential Phase Shift Keying data format. The modelling is completed using the Split-Step Fourier Method to solve the Generalised Nonlinear Schrdinger Equation. We optimise the dispersion map and per-channel launch power of these channels and investigate how the choice of pre/post compensation can influence the performance. After obtaining these optimal configurations, we investigate the Bit Error Rate estimation of these systems and we see that estimation based on Gaussian electrical current systems is appropriate for systems of this type, indicating quasi-linear behaviour. The introduction of narrower pulses due to the deployment of quasi-linear transmission decreases the tolerance to chromatic dispersion and intra-channel nonlinearity. We used tools from Mathematical Statistics to study the behaviour of these channels in order to develop new methods to estimate Bit Error Rate. In the final section, we consider the estimation of Eye Closure Penalty, a popular measure of signal distortion. Using a numerical example and assuming the symmetry of eye closure, we see that we can simply estimate Eye Closure Penalty using Gaussian statistics. We also see that the statistics of the logical ones dominates the statistics of the logical ones dominates the statistics of signal distortion in the case of Return-to-Zero On-Off Keying configurations.

Structure-function analysis of amino acid 74 of human RAMP1 and RAMP3 and its role in peptide interactions with adrenomedullin and calcitonin gene-related peptide receptors

The receptors for calcitonin gene-related peptide (CGRP) and adrenomedullin (AM) are complexes of the calcitonin receptor-like receptor (CLR) and receptor activity-modifying proteins (RAMP). The CGRP receptor is a CLR/RAMP1 pairing whereas CLR/RAMP2 and CLR/RAMP3 constitute two subtypes of AM receptor: AM(1) and AM(2), respectively. Previous studies identified Glu74 in RAMP3 to be important for AM binding and potency. To further understand the importance of this residue and its equivalent in RAMP1 (Trp74) we substituted the native amino acids with several others. In RAMP3, these were Trp, Phe, Tyr, Ala, Ser, Thr, Arg and Asn; in RAMP1, Glu, Phe, Tyr, Ala and Asn substitutions were made. The mutant RAMPs were co-expressed with CLR in Cos7 cells; receptor function in response to AM, AM(2)/intermedin and CGRP was measured in a cAMP assay and cell surface expression was determined by ELISA. Phe reduced AM potency in RAMP3 but had no effect in RAMP1. In contrast, Tyr had no effect in RAMP3 but enhanced AM potency in RAMP1. Most other substitutions had a small effect on AM potency in both receptors whereas there was little impact on CGRP or AM(2) potency. Overall, these data suggest that the geometry and charge of the residue at position 74 contribute to how AM interacts with the AM(2) and CGRP receptors and confirms the role of this position in dictating differential AM pharmacology at the AM(2) and CGRP receptors.

Identification and analysis of moderator variables:investigating the customer satisfaction-loyalty link

Purpose – Research on the relationship between customer satisfaction and customer loyalty has advanced to a stage that requires a more thorough examination of moderator variables. Limited research shows how moderators influence the relationship between customer satisfaction and customer loyalty in a service context; this article aims to present empirical evidence of the conditions in which the satisfaction-loyalty relationship becomes stronger or weaker. Design/methodology/approach – Using a sample of more than 700 customers of DIY retailers and multi-group structural equation modelling, the authors examine moderating effects of several firm-related variables, variables that result from firm/employee-customer interactions and individual-level variables (i.e. loyalty cards, critical incidents, customer age, gender, income, expertise). Findings – The empirical results suggest that not all of the moderators considered influence the satisfaction-loyalty link. Specifically, critical incidents and income are important moderators of the relationship between customer satisfaction and customer loyalty. Practical implications – Several of the moderator variables considered in this study are manageable variables. Originality/value – This study should prove valuable to academic researchers as well as service and retailing managers. It systematically analyses the moderating effect of firm-related and individual-level variables on the relationship between customer satisfaction and loyalty. It shows the differential effect of different types of moderator variables on the satisfaction-loyalty link.

Performance analysis of 20 Gbit/s RZ-DPSK non-slope matched transoceanic submarine links

This paper studies the performance of a typical non-slope matched transoceanic submarine link using 20Gb/s channel rate and RZ-DPSK modulation with different duty cycles. Through comparison with direct error counting, we have also demonstrated the limitations of the available numerical approaches to the BER estimation for return-to-zero differential phase-shift keying (RZ-DPSK). The numerical results have been confirmed by experiments, and indicate that 20 Gb/s RZ-DPSK transmission is a feasible technique for the upgrade of existing submarine links.

Comparative analysis of BER estimation methods in numerical simulation of 40-Gb/s RZ-DPSK transmission with in-line SOAs

Applying direct error counting, we compare the accuracy and evaluate the validity of different available numerical approaches to the estimation of the bit-error rate (BER) in 40-Gb/s return-to-zero differential phase-shift-keying transmission. As a particular example, we consider a system with in-line semiconductor optical amplifiers. We demonstrate that none of the existing models has an absolute superiority over the others. We also reveal the impact of the duty cycle on the accuracy of the BER estimates through the differently introduced Q-factors.