The diagenesis and palaeomagnetism of permian and triassic sediments from central Spain

Detailed diagenetic and palaeomagnetic studies have been made of Permian and Triassic rocks from the Iberian Cordillera, Spain. Five stratigraphical units comprising the Autunian, Saxonian, Buntsandstein, Muschelkalk, and Keuper have been studied in a number of sections which have been well documented sedimentologically. Autuninan rocks have a characteristic remanence which is exclusively reversed and corresponds to the Kiaman Interval. The pole position identified is consistent with previous studies, which indicate the rotation of Iberia in post-Triassic times. The Saxonian facies show complex multicomponent magnetizations; no polarity zonation can be resolved. The Buntsandstein is remarkable in that much of it is remagnetised in a direction similar to the present-day local geomagnetic field direction. The secondary remanence is carried by fine-grained haematite which has been formed as a result of carbonate dissolution associated with structural inversion of the Iberian Cordillera. Dating of diagenetic events associated with this remagnetization is also possible. Fragments of primary remanence are preserved in some fine-grained lithologies of the Buntsandstein. These indicate that normal and reversed zones of magnetization were originally present. The magnetization of the Muschelkalk and Keuper carbonates is also complex; secondary components similar to those of the Buntsandstein are present but there is evidence that primary components were predominantly normal during Karnian times.

An optical pump controlled tunable phase-shifted fiber grating transmission filter

Optical pump controlled, remotely tunable phase-shifted fiber grating transmission filters were analyzed. The transmission peak had a full width hail maximum (FWHM) bandwidth. With increasing control pump power, the resonant peak shifted towards the longer wavelength side. The efficiency of the system was largely affected by the greater number of sections of doped fiber as well as the absence of recirculation of unabsorbed pump beam. The configuration, besides its simplicity and cost-effectiveness, exhibited wavelength-independent pump-induced phase shifts and no anisotropic effects during operation.

Quantitative microscopic analysis of histological sections of brain tissue

This article reviews methods for quantifying the abundance of histological features in thin tissue sections of brain such as neurons, glia, blood vessels, and pathological lesions. The sampling methods by which quantitative measures can be obtained are described. In addition, methods are described for determining the spatial pattern of an object and for measuring the degree of spatial correlation between two or more histological features.

Measuring the spatial arrangement patterns of pathological lesions in histological sections of brain tissue

The development of abnormal protein aggregates in the form of extracellular plaques and intracellular inclusions is a characteristic feature of many neurodegenerative diseases such as Alzheimer's disease (AD), Creutzfeldt-Jakob disease (CJD) and the fronto-temporal dementias (FTD). An important aspect of a pathological protein aggregate is its spatial topography in the tissue. Lesions may not be randomly distributed within a histological section but exhibit spatial pattern, a departure from randomness either towards regularity or clustering. Information on the spatial pattern of a lesion may be useful in elucidating its pathogenesis and in studying the relationships between different lesions. This article reviews the methods that have been used to study the spatial topography of lesions. These include simple tests of whether the distribution of a lesion departs significantly from random using randomized points or sample fields, and more complex methods that employ grids or transects of contiguous fields and which can detect the intensity of aggregation and the sizes, distribution and spacing of the clusters. The usefulness of these methods in elucidating the pathogenesis of protein aggregates in neurodegenerative disease is discussed.

Methods of studying the planar distribution of objects in histological sections of brain tissue

This article reviews the statistical methods that have been used to study the planar distribution, and especially clustering, of objects in histological sections of brain tissue. The objective of these studies is usually quantitative description, comparison between patients or correlation between histological features. Objects of interest such as neurones, glial cells, blood vessels or pathological features such as protein deposits appear as sectional profiles in a two-dimensional section. These objects may not be randomly distributed within the section but exhibit a spatial pattern, a departure from randomness either towards regularity or clustering. The methods described include simple tests of whether the planar distribution of a histological feature departs significantly from randomness using randomized points, lines or sample fields and more complex methods that employ grids or transects of contiguous fields, and which can detect the intensity of aggregation and the sizes, distribution and spacing of clusters. The usefulness of these methods in understanding the pathogenesis of neurodegenerative diseases such as Alzheimer's disease and Creutzfeldt-Jakob disease is discussed. © 2006 The Royal Microscopical Society.

Measuring the degree of spatial correlation between histological features in thin sections of brain tissue

Histological features visible in thin sections of brain tissue, such as neuronal perikarya, blood vessels, or pathological lesions may exhibit a degree of spatial association or correlation. In neurodegenerative disorders such as AD, Pick's disease, and CJD, information on whether different types of pathological lesion are spatially correlated may be useful in elucidating disease pathogenesis. In the present article the statistical methods available for studying spatial association in histological sections are reviewed. These include tests of interspecific association between two or more histological features using χ2 contingency tables, measurement of 'complete' and 'absolute' association, and more complex methods that use grids of contiguous samples. In addition, the use of correlation matrices and stepwise multiple regression methods are described. The advantages and limitations of each method are reviewed and possible future developments discussed.

Mass spectrometry imaging of pharmacological compounds in tissue sections

The use of MS imaging (MSI) to resolve the spatial and pharmacodynamic distributions of compounds in tissues is emerging as a powerful tool for pharmacological research. Unlike established imaging techniques, only limited a priori knowledge is required and no extensive manipulation (e.g., radiolabeling) of drugs is necessary prior to dosing. MS provides highly multiplexed detection, making it possible to identify compounds, their metabolites and other changes in biomolecular abundances directly off tissue sections in a single pass. This can be employed to obtain near cellular, or potentially subcellular, resolution images. Consideration of technical limitations that affect the process is required, from sample preparation through to analyte ionization and detection. The techniques have only recently been adapted for imaging and novel variations to the established MSI methodologies will further enhance the application of MSI for pharmacological research.

Simplified preparation of human arterial sections for PCR analysis of Chlamydia pneumoniae and human DNA

AIMS: To investigate multiple techniques for the preparation of solid tissue for polymerase chain reaction (PCR) analysis, and to identify the most simple techniques for routine use in the laboratory. METHODS: Techniques for the preparation of arterial tissue samples including homogenisation, ultrafiltration, and treatments involving proteinase K, Gene Clean, lectin, and Fe3+ specific chelators were evaluated using the PCR to amplify both Chlamydia pneumoniae and human DNA. RESULTS: Treatment with either Gene-Clean or lectin and the Fe3+ specific chelator deferoxamine mesylate removed PCR inhibitors from tissue homogenates. Homogenisation followed by GeneClean treatment resulted in the amplification of C pneumoniae DNA from within a section of atherosclerotic carotid artery, implying that C pneumoniae elementary bodies had been disrupted. In eight further clinical samples from patients not known to have C pneumoniae infection, human DNA was amplified and no cross contamination was observed between samples. These samples contained no evidence of C pneumoniae by PCR. CONCLUSIONS: A simple preparation of solid tissue for PCR analysis, involving homogenisation followed by GeneClean treatment has been developed, and is effective for the amplification of both C pneumoniae and human DNA.

Analysis of spatial patterns in histological sections of brain tissue using a method based on regression

A method of determining the spatial pattern of any histological feature in sections of brain tissue which can be measured quantitatively is described and compared with a previously described method. A measurement of a histological feature such as density, area, amount or load is obtained for a series of contiguous sample fields. The regression coefficient (β) is calculated from the measurements taken in pairs, first in pairs of adjacent samples and then in pairs of samples taken at increasing degrees of separation between them, i.e. separated by 2, 3, 4,..., n units. A plot of β versus the degree of separation between the pairs of sample fields reveals whether the histological feature is distributed randomly, uniformly or in clusters. If the feature is clustered, the analysis determines whether the clusters are randomly or regularly distributed, the mean size of the clusters and the spacing of the clusters. The method is simple to apply and interpret and is illustrated using simulated data and studies of the spatial patterns of blood vessels in the cerebral cortex of normal brain, the degree of vacuolation of the cortex in patients with Creutzfeldt-Jacob disease (CJD) and the characteristic lesions present in Alzheimer's disease (AD). Copyright (C) 2000 Elsevier Science B.V.

Analysis of spatial patterns in histological sections of brain tissue

A method is described which enables the spatial pattern of discrete objects in histological sections of brain tissue to be determined. The method can be applied to cell bodies, sections of blood vessels or the characteristic lesions which develop in the brain of patients with neurodegenerative disorders. The density of the histological feature under study is measured in a series of contiguous sample fields arranged in a grid or transect. Data from adjacent sample fields are added together to provide density data for larger field sizes. A plot of the variance/mean ratio (V/M) of the data versus field size reveals whether the objects are distributed randomly, uniformly or in clusters. If the objects are clustered, the analysis determines whether the clusters are randomly or regularly distributed and the mean size of the clusters. In addition, if two different histological features are clustered, the analysis can determine whether their clusters are in phase, out of phase or unrelated to each other. To illustrate the method, the spatial patterns of senile plaques and neurofibrillary tangles were studied in histological sections of brain tissue from patients with Alzheimer's disease.

Analysis of population dispersion in histological sections

Stereology and other image analysis methods have enabled rapid and objective quantitative measurements to be made on histological sections. These mesurements may include total volumes, surfaces, lengths and numbers of cells and blood vessels or pathological lesions. Histological features, however, may not be randomly distributed across a section but exhibit 'dispersion', a departure from randomness either towards regularity or aggregation. Information of population dispersion may be valuable not only in understanding the two-or three-dimensional structure but also in elucidating the pathogenesis of lesions in pathological conditions. This article reviews some of the statistical methods available for studying dispersion. These range from simple tests of whether the distribution of a histological faeture departs significantly from random to more complex methods which can detect the intensity of aggregation and the sizes, distribution and spacing of the clusters.

The Mechanics of the drawing of polygonal sections from round at elevated temperature

Economic factors such as the rise in cost of raw materials, labour and power, are compelling manufacturers of cold-drawn polygonal sections, to seek new production routes which will enable the expansion in the varieties of metals used and the inclusion of difficult-to-draw materials. One such method generating considerable industrial interest is the drawing of polygonal sections from round at elevated temperature. The technique of drawing mild steel, medium carbon steel and boron steel wire into octagonal, hexagonal and square sections from round at up to 850 deg C and 50% reduction of area in one pass has been established. The main objective was to provide a basic understanding of the process, with particular emphasis being placed on modelling using both experimental and theoretical considerations. Elevated temperature stress-strain data was obtained using a modified torsion testing machine. Data were used in the upper bound solution derived and solved numerically to predict drawing stress strain, strain-rate, temperature and flow stress distribution in the deforming zone for a range of variables. The success of this warm working process will, of course, depend on the use of a satisfactory elevated temperature lubricant, an efficient cooling system, a suitable tool material having good wear and thermal shock resistance and an efficient die profile design which incorporates the principle of least work. The merits and demerits of die materials such as tungsten carbide, chromium carbide, Syalon and Stellite are discussed, principally from the standpoint of minimising drawing force and die wear. Generally, the experimental and theoretical results were in good agreement, the drawing stress could be predicted within close limits and the process proved to be technically feasible. Finite element analysis has been carried out on the various die geometries and die materials, to gain a greater understanding of the behaviour of these dies under the process of elevated temperature drawing, and to establish the temperature distribution and thermal distortion in the deforming zone, thus establishing the optimum die design and die material for the process. It is now possible to predict, for the materials already tested, (i) the optimum drawing temperature range, (ii) the maximum possible reduction of area per pass, (iii) the optimum drawing die profiles and die materials, (iv) the most efficient lubricant in terms of reducing the drawing force and die wear.

Computer aided design and analysis of cold formed sections

The work reported in this thesis is concerned with the improvement and expansion of the assistance given to the designer by the computer in the design of cold formed sections. The main contributions have been in four areas, which have consequently led to the fifth, the development of a methodology to optimise designs. This methodology can be considered an `Expert Design System' for cold formed sections. A different method of determining section properties of profiles was introduced, using the properties of line and circular elements. Graphics were introduced to show the outline of the profile on screen. The analysis of beam loading has been expanded to beam loading conditions where the number of supports, point loads, and uniform distributive loads can be specified by the designer. The profile can then be checked for suitability for the specified type of loading. Artificial Intelligence concepts have been introduced to give the designer decision support from the computer, in combination with the computer aided design facilities. The more complex decision support was adopted through the use of production rules. All the support was based on the British standards. A method has been introduced, by which the appropriate use of stiffeners can be determined and consequently designed by the designer. Finally, the methodology by which the designer is given assistance from the computer, without constraining the designer, was developed. This methodology gives advice to the designer on possible methods of improving the design, but allows the designer to reject that option, and analyse the profile accordingly. The methodology enables optimisation to be achieved by the designer, designing variety of profiles for a particular loading, and determining which one is best suited.