The influence of cutting tool geometry upon aspects of chip flow and tool wear:a theoretical, three dimensional examination of the cutting geometry and the shape of the twist drill

This work is undertaken in the attempt to understand the processes at work at the cutting edge of the twist drill. Extensive drill life testing performed by the University has reinforced a survey of previously published information. This work demonstrated that there are two specific aspects of drilling which have not previously been explained comprehensively. The first concerns the interrelating of process data between differing drilling situations, There is no method currently available which allows the cutting geometry of drilling to be defined numerically so that such comparisons, where made, are purely subjective. Section one examines this problem by taking as an example a 4.5mm drill suitable for use with aluminium. This drill is examined using a prototype solid modelling program to explore how the required numerical information may be generated. The second aspect is the analysis of drill stiffness. What aspects of drill stiffness provide the very great difference in performance between short flute length, medium flute length and long flute length drills? These differences exist between drills of identical point geometry and the practical superiority of short drills has been known to shop floor drilling operatives since drilling was first introduced. This problem has been dismissed repeatedly as over complicated but section two provides a first approximation and shows that at least for smaller drills of 4. 5mm the effects are highly significant. Once the cutting action of the twist drill is defined geometrically there is a huge body of machinability data that becomes applicable to the drilling process. Work remains to interpret the very high inclination angles of the drill cutting process in terms of cutting forces and tool wear but aspects of drill design may already be looked at in new ways with the prospect of a more analytical approach rather than the present mix of experience and trial and error. Other problems are specific to the twist drill, such as the behaviour of the chips in the flute. It is now possible to predict the initial direction of chip flow leaving the drill cutting edge. For the future the parameters of further chip behaviour may also be explored within this geometric model.

The cutting performance of sialon ceramic tools

The thesis deals with a research programme in which the cutting performance of a new generation of ceramic cutting tool material is evaluated using the turning process. In part one, the performance of commercial Kyon 2000 sialon ceramic inserts is studied when machining a hardened alloy steel under a wide range of cutting conditions. The aim is to formulate a pattern of machining behaviour in which tool wear is related to a theoretical interpretation of the temperatures and stresses generated by the chip-tool interaction. The work involves a correlation of wear measurement and metallographic examination of the wear area with the measurable cutting data. Four main tool failure modes are recognised: (a) flank and crater wear (b) grooving wear (c) deformation wear and (d) brittle failure Results indicate catastrophic edge breakdown under certain conditions. Accordingly in part two, the edge geometry is modified to give a double rake tool; a negative/positive combination. The results are reported for a range of workpiece materials under orthogonal cutting conditions. Significant improvements in the cutting performance are achieved. The improvements are explained by a study of process parameters; cutting forces, chip thickness ratio, chip contact length, temperature distribution, stress distribution and chip formation. In part three, improvements in tool performance are shown to arise when the edge chamfer on a single rake tool is modified. Under optimum edge chamfer conditions a substantial increase in tool life is obtained compared with the commercial cutting geometry.

Modelling the dynamics of cutting during turning

This thesis presents an approach to cutting dynamics during turning based upon the mechanism of deformation of work material around the tool nose known as "ploughing". Starting from the shearing process in the cutting zone and accounting for "ploughing", new mathematical models relating turning force components to cutting conditions, tool geometry and tool vibration are developed. These models are developed separately for steady state and for oscillatory turning with new and worn tools. Experimental results are used to determine mathematical functions expressing the parameters introduced by the steady state model in the case of a new tool. The form of these functions are of general validity though their coefficients are dependent on work and tool materials. Good agreement is achieved between experimental and predicted forces. The model is extended on one hand to include different work material by introducing a hardness factor. The model provides good predictions when predicted forces are compared to present and published experimental results. On the other hand, the extension of the ploughing model to taming with a worn edge showed the ability of the model in predicting machining forces during steady state turning with the worn flank of the tool. In the development of the dynamic models, the dynamic turning force equations define the cutting process as being a system for which vibration of the tool tip in the feed direction is the input and measured forces are the output The model takes into account the shear plane oscillation and the cutting configuration variation in response to tool motion. Theoretical expressions of the turning forces are obtained for new and worn cutting edges. The dynamic analysis revealed the interaction between the cutting mechanism and the machine tool structure. The effect of the machine tool and tool post is accounted for by using experimental data of the transfer function of the tool post system. Steady state coefficients are corrected to include the changes in the cutting configuration with tool vibration and are used in the dynamic model. A series of oscillatory cutting tests at various conditions and various tool flank wear levels are carried out and experimental results are compared with model—predicted forces. Good agreement between predictions and experiments were achieved over a wide range of cutting conditions. This research bridges the gap between the analysis of vibration and turning forces in turning. It offers an explicit expression of the dynamic turning force generated during machining and highlights the relationships between tool wear, tool vibration and turning force. Spectral analysis of tool acceleration and turning force components led to define an "Inertance Power Ratio" as a flank wear monitoring factor. A formulation of an on—line flank wear monitoring methodology is presented and shows how the results of the present model can be applied to practical in—process tool wear monitoring in • turning operations.

Optical data transmission using periodic in-line all-optical format conversion

We introduce a novel transmission technique of periodic in-line all-optical format conversion between return-to-zero and non-return-to-zero-like aimed at delaying the accumulation of format-specific impairments. A particular realization of this approach using in-line normal dispersion fibre-enhanced nonlinear optical loop mirrors at 40Gbit/s data rate is presented. © 2004 Optical Society of America.

Optical data transmission using periodic in-line all-optical format conversion

We introduce a novel transmission technique of periodic in-line all-optical format conversion between return-to-zero and non-return-to-zero-like aimed at delaying the accumulation of format-specific impairments. A particular realization of this approach using in-line normal dispersion fibre-enhanced nonlinear optical loop mirrors at 40Gbit/s data rate is presented.

Prediction equations for cutting forces while oblique machining EN-8 steels employing 'response surface methodology'

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

All-optical 42.6 Gbit/s NRZ to RZ format conversion by cross-phase modulation in single SOA

A 42.6 Gbit/s all-optical non-retum-to-zero (NRZ) to return-to-zero (RZ) format converter using a single SOA followed by an asymmetrical Mach-Zehnder interferometer is presented. The format converter generates a correctly-coded RZ signal with a controllable duty-cycle. It has the advantages of flexible input N RZ wavelength, preserved input polarity, negative bit error rate power penalty and low switching pulse energy (15fJ).

Simultaneous multiple channel all-optical NRZ to CSRZ and RZ to CSRZ format conversion using an SOA-NOLM

The optical conversion bandwidth for an all-optical modulation format converter, based on a semiconductor laser amplifier in a nonlinear optical loop mirror (SOA-NOLM), is investigated. 4 Â 10 Gbit/s channels are all- optically converted between both non-return-to-zero (NRZ) and return-to-zero (RZ) format to carrier- suppressed return-to-zero (CSRZ). WDM transmission of the converted signals over a 194 km fibre span is then demonstrated. The receiver sensitivity for the converted four wavelengths is measured and compared after transmission.

Simultaneous multiple channel all-optical NRZ to CSRZ and RZ to CSRZ format conversion using an SOA-NOLM

The optical conversion bandwidth for an all-optical modulation format converter, based on a semiconductor laser amplifier in a nonlinear optical loop mirror (SOA-NOLM), is investigated. 4 Â 10 Gbit/s channels are all- optically converted between both non-return-to-zero (NRZ) and return-to-zero (RZ) format to carrier- suppressed return-to-zero (CSRZ). WDM transmission of the converted signals over a 194 km fibre span is then demonstrated. The receiver sensitivity for the converted four wavelengths is measured and compared after transmission.

Simultaneous multiple channel all-optical NRZ to CSRZ and RZ to CSRZ format conversion using an SOA-NOLM

The optical conversion bandwidth for an all-optical modulation format converter, based on a semiconductor laser amplifier in a nonlinear optical loop mirror (SOA-NOLM), is investigated. 4×10 Gbit/s channels are all-optically converted between both non-return-to-zero (NRZ) and return-to-zero (RZ) format to carrier-suppressed return-to-zero (CSRZ). WDM transmission of the converted signals over a 194 km fibre span is then demonstrated. The receiver sensitivity for the converted four wavelengths is measured and compared after transmission. © 2014 Elsevier B.V. All rights reserved.

Optimally-designed single fiber Bragg grating filter scheme for RZ-OOK/DPSK/DQPSK to NRZ-OOK/DPSK/DQPSK format conversion

We investigate return-to-zero (RZ) to non-return-to-zero (NRZ) format conversion by means of the linear time-invariant system theory. It is shown that the problem of converting random RZ stream to NRZ stream can be reduced to constructing an appropriate transfer function for the linear filter. This approach is then used to propose novel optimally-designed single fiber Bragg grating (FBG) filter scheme for RZ-OOK/DPSK/DQPSK to NRZ-OOK/DPSK/DQPSK format conversion. The spectral response of the FBG is designed according to the optical spectra of the algebraic difference between isolated NRZ and RZ pulses, and the filter order is optimized for the maximum Q-factor of the output NRZ signals. Experimental results as well as simulations show that such an optimallydesigned FBG can successfully perform RZ-OOK/DPSK/DQPSK to NRZOOK/ DPSK/DQPSK format conversion.

CLAE to move to online format

Editorial: The 2015 BCLA annual conference was another fantastic affair. It was the first time the conference was held in the beautiful city of Liverpool. The venue was great and the programme was excellent. The venue overlooked the River Mersey and many of the hotels were local boutique hotels. I stayed in one which was formerly the offices of White Star Liners—where the RMS Titanic was originally registered. The hotel decor was consistent with its historic significance. The BCLA gala dinner was held in the hugely impressive Anglican Cathedral with entertainment from a Beatles tribute band. That will certainly be a hard act to follow at the next conference in 2017. Brian Tompkins took the reigns as the new BCLA president. Professor Fiona Stapleton was the recipient of the BCLA Gold Medal Award. The winner of the poster competition was Dorota Szczesna-Iskander with a poster entitled ‘Dry Contact lens poor wettability and visual performance’. Second place was Renee Reeder with her poster entitled ‘Abnormal Rosacea as a differential diagnosis in corneal scarring’. And third place was Maria Jesus Gonzalez-Garcia with her poster entitled ‘Dry Effect of the Environmental Conditions on Tear Inflammatory Mediators Concentration in Contact Lens Wearers’. The photographic competition winner was Professor Wolfgang Sickenberger from Jena in Germany. The Editorial Panel of CLAE met at the BCLA conference for their first biannual meeting. The journal metrics were discussed. In terms of number of submissions of new papers CLAE seems to have plateaued after seeing a rapid growth in the number of submissions over the last few years. The increase over the last few years could be attributed to the fact that CLAE was awarded an impact factor for the first time in 2012. This year it seems that impact factors across nearly all ophthalmic related journals has dropped. This could in part be due to the fact that last year was a ‘Research Exercise Framework (REF) year for UK universities, where they are judged on quality of their research output. The next REF is in 2020 so we may see changes nearing that time. Looking at article downloads, there seems to be a continued rise in figures. Currently CLAE attracts around 85,000 downloads per year (this is an increase of around 10,000 per year for the last few years) and the 2015 prediction is 120,000! With this in mind and with other contributing factors too, the BCLA has decided to move to online delivery of CLAE to its members starting from issue 5 of 2015. Some members do like to flick through the pages of a hard copy of the journal so members will still have the option of receiving a hard copy through the post but the default journal delivery method will now be online. The BCLA office will send various alerts and content details to members email addresses. To access CLAE online you will need to log in via the BCLA web page, currently you then click on ‘Resources’ and then under ‘Free and Discounted Publications’ you will see CLAE. This actually takes you to CLAE’s own webpage (www.contactlensjournal.com) but you need to log in via the BCLA web page. The BCLA plans to change these weblinks so that from the BCLA web page you can link to the journal website much more easily and you have the choice of going directly into the general website for CLAE or straight to the current issue. In 2016 you will see an even easier way of accessing CLAE online as the BCLA will launch a CLAE application for mobile devices where the journal can be downloaded as a ‘flick-book’. This is a great way of bringing CLAE into the modern era where people access their information in newer ways. For many the BCLA conference was part of a very busy conference week as it was preceded by the International Association of Contact Lens Educators’ (IACLE) Third World Congress, held in Manchester on the 4 days before the BCLA conference. The first and second IACE World Congresses were held in Waterloo, Canada in 1994 and 2000 respectively and hosted by Professor Des Fonn. Professor Fonn was the recipient of the first ever IACLE lifetime achievement award. The Third IACLE World Congress saw more than 100 contact lens educators and industry representatives from around 30 countries gather in the UK for the four-day event, hosted by The University of Manchester. Delegates gained hands-on experience of innovations in teaching, such as learning delivery systems, the use of iPads in the classroom and for creating ePub content, and augmented and virtual reality technologies. IACLE members around the world also took part via a live online broadcast. The Third IACLE World Congress was made possible by the generous support of Sponsors Alcon, CooperVision and Johnson & Johnson Vision Care., for more information look at the IACLE web page (www.iacle.org).

Comparison of the measurement performance of high precision multi-axis metal cutting machine tools

High precision manufacturers continuously seek out disruptive technologies to improve the quality, cost, and delivery of their products. With the advancement of machine tool and measurement technology many companies are ready to capitalise on the opportunity of on-machine measurement (OMM). Coupled with business case, manufacturing engineers are now questioning whether OMM can soon eliminate the need for post-process inspection systems. Metrologists will however argue that the machining environment is too hostile and that there are numerous process variables which need consideration before traceable measurement on-the-machine can be achieved. In this paper we test the measurement capability of five new multi-axis machine tools enabled as OMM systems via on-machine probing. All systems are tested under various operating conditions in order to better understand the effects of potentially significant variables. This investigation has found that key process variables such as machine tool warm-up and tool-change cycles can have an effect on machine tool measurement repeatability. New data presented here is important to many manufacturers whom are considering utilising their high precision multi-axis machine tools for both the creation and verification of their products.

Simultaneous multichannel carrier-suppressed return-to-zero to non-return-to-zero format conversion using a fiber Bragg grating

A novel multichannel carrier-suppressed return-to-zero (CSRZ) to non-return-to-zero (NRZ) format conversion scheme based on a single custom-designed fiber Bragg grating (FBG) with comb spectra is proposed. The spectral response of each channel is designed according to the algebraic difference between the CSRZ and NRZ spectra outlines. The tailored group delays are introduced to minimize the maximum refractive index modulation. Numerical results show that four-channel 200-GHz-spaced CSRZ signals at 40 Gbits/s can be converted into NRZ signals with high Q-factor and wide-range robustness. It is shown that our proposed FBG is robust to deviations of bandwidth and central wavelength detuning. Another important merit of this scheme is that the pattern effects are efficiently reduced owing to the well-designed spectra response.

Cutting the Gordian knot [?]:a response to Lukka and Vinnari (2014)

Purpose – The purpose of this paper is to constructively discuss the meaning and nature of (theoretical) contribution in accounting research, as represented by Lukka and Vinnari (2014) (hereafter referred to as LV). The authors aim is to further encourage debate on what constitutes management accounting theory (or theories) and how to modestly clarify contributions to the extant literature. Design/methodology/approach – The approach the authors take can be seen as (a)n interdisciplinary literature sourced analysis and critique of the movement’s positioning and trajectory” (Parker and Guthrie, 2014, p. 1218). The paper also draws upon and synthesizes the present authors and other’s contributions to accounting research using actor network theory. Findings – While a distinction between domain and methods theories … may appear analytically viable, it may be virtually impossible to separate them in practice. In line with Armstrong (2008), the authors cast a measure of doubt on the quest to significantly extend theoretical contributions from accounting research. Research limitations/implications – Rather than making (apparently) grandiose claims about (theoretical) contributions from individual studies, the authors suggest making more modest claims from the research. The authors try to provide a more appropriate and realistic approach to the appreciation of research contributions. Originality/value – The authors contribute to the debate on how theoretical contributions can be made in the accounting literature by constructively debating some views that have recently been outlined by LV. The aim is to provide some perspective on the usefulness of the criteria suggested by these authors. The authors also suggest and highlight (alternative) ways in which contributions might be discerned and clarified.