Optimizing supply chain waste management through the use of RFID technology

This paper presents a Decision Support System framework based on Constrain Logic Programming and offers suggestions for using RFID technology to improve several of the critical procedures involved. This paper suggests that a widely distributed and semi-structured network of waste producing and waste collecting/processing enterprises can improve their planning both by the proposed Decision Support System, but also by implementing RFID technology to update and validate information in a continuous manner. © 2010 IEEE.

Decision making in nuclear waste management:the use of the synoptic approach

This thesis is concerned with the use of the synoptic approach within decision making concerning nuclear waste management. The synoptic approach to decision making refers to an approach to rational decision making that assumes as an ideal, comprehensiveness of information and analysis. Two case studies are examined in which a high degree of synoptic analysis has been used within the decision making process. The case studies examined are the Windscale Inquiry into the decision to build the THORP reprocessing plant and the Nirex safety assessment of nuclear waste disposal. The case studies are used to test Lindblom's hypothesis that a synoptic approach to decision making is not achievable. In the first case study Lindblom's hypothesis is tested through the evaluation of the decision to build the THORP plant, taken following the Windscale Inquiry. It is concluded that the incongruity of this decision supports Lindblom's hypothesis. However, it has been argued that the Inquiry should be seen as a legitimisation exercise for a decision that was effectively predetermined, rather than a rigorous synoptic analysis. Therefore, the Windscale Inquiry does not provide a robust test of the synoptic method. It was concluded that a methodology was required, that allowed robust conclusions to be drawn, despite the ambiguity of the role of the synoptic method in decision making. Thus, the methodology adopted for the second case study was modified. In this case study the synoptic method was evaluated directly. This was achieved through the analysis of the cogency of the Nirex safety assessment. It was concluded that the failure of Nirex to provide a cogent synoptic analysis supported Lindblom's criticism of the synoptic method. Moreover, it was found that the synoptic method failed in the way that Lindblom predicted that it would.

Characterisation of waste derived intermediate pyrolysis oils for use as diesel engine fuels

This paper studies the characteristics of intermediate pyrolysis oils derived from sewage sludge and de-inking sludge (a paper industry residue), with a view to their use as fuels in a diesel engine. The feedstocks were dried and pelletised, then pyrolysed in the Pyroformer intermediate pyrolysis system. The organic fraction of the oils was separated from the aqueous phase and characterised. This included elemental and compositional analysis, heating value, cetane index, density, viscosity, surface tension, flash point, total acid number, lubricity, copper corrosion, water, carbon residue and ash content. Most of these results are compared with commercial diesel and biodiesel. Both pyrolysis oils have high carbon and hydrogen contents and their higher heating values compare well with biodiesel. The water content of the pyrolysis oils is reasonable and the flash point is found to be high. Both pyrolysis oils have good lubricity, but show some corrosiveness. Cetane index is reduced, which may influence ignition. Also viscosity is increased, which may influence atomisation quality. Carbon residue and ash content are both high, indicating potential deposition problems. Compared with de-inking sludge pyrolysis oil (DSPO), sewage sludge pyrolysis oil (SSPO) has a higher heating value, but higher corrosiveness and viscosity. The conclusions are that both intermediate pyrolysis oils will be able to provide sufficient heat when used in diesel engine; however poor combustion and carbon deposition may be encountered. Blending of these pyrolysis oils with diesel or biodiesel could overcome these problems and is recommended for further investigation.

A review of barriers to kerbside recycling household waste in the UK

The aim of this work is to use systematic review methodology to answer the question “What are the current barriers to kerbside recycling of household waste in the UK?” A systematic search of electronic databases and journals was undertaken to identify academic published work. A critical scoping review of research published between 2000 – 2008 profiles theory and research design. The systematic review identified twelve relevant papers, of which seven contain original data. To define the current barriers the explanations of barriers were systematically aggregated into four main categories: household / individual behaviour; services / local situation; attitudes / motivation; information and knowledge. The purpose of the work is to inform future marketing campaigns which will assist the UK to reach the statutory targets of waste diversion. The synthesis will be useful to environmental professionals working in waste authorities and researchers and students. The framework offers an opportunity to develop better marketing and communications strategies to help more people recycle more things more often and will inform future recycling policy development.

'Urine testing is a waste of time': newly diagnosed Type 2 diabetes patients' perceptions of self-monitoring

Aims To date, there is no convincing evidence that non-insulin treated patients who undertake self-blood glucose monitoring (SBGM) have better glycaemic control than those who test their urine. This has led to a recommendation that non-insulin dependent patients undertake urine testing, which is the cheaper option. This recommendation does not take account of patients' experiences and views. This study explores the respective merits of urine testing and SBGM from the perspectives of newly diagnosed patients with Type 2 diabetes. Methods Qualitative study using repeat in-depth interviews with 40 patients. Patients were interviewed three times at 6-monthly intervals over 1 year. Patients were recruited from hospital clinics and general practices in Lothian, Scotland. The study was informed by grounded theory, which involves concurrent data collection and analysis. Results Patients reported strongly negative views of urine testing, particularly when they compared it with SBGM. Patients perceived urine testing as less convenient, less hygienic and less accurate than SBGM. Most patients assumed that blood glucose meters were given to those with a more advanced or serious form of diabetes. This could have implications for how they thought about their own disease. Patients often interpreted negative urine results as indicating that they could not have diabetes. Conclusions Professionals should be aware of the meanings and understandings patients attach to the receipt and use of different types of self-monitoring equipment. Guidelines that promote the use of consistent criteria for equipment allocation are required. The manner in which negative urine results are conveyed needs to be reconsidered.

Returned medicines:Waste or a wasted opportunity?

Background: Re-use of unused medicines returned from patients is currently considered unethical in the UK and these are usually destroyed by incineration. Previous studies suggest that many of these medicines may be in a condition suitable for re-use. Methods: All medicines returned over two months to participating community pharmacies and GP surgeries in Eastern Birmingham PCT were assessed for type, quantity and value. A registered pharmacist assessed packs against set criteria to determine the suitability for possible re-use. Results: Nine hundred and thirty-four return events were made from 910 patients, comprising 3765 items worth £33 608. Cardiovascular drugs (1003, 27%) and those acting on the CNS (884, 24%) were most prevalent. Returned packs had a median of 17 months remaining before expiry and one-quarter of packs (1248 out of 4291) were suitable for possible re-use. One-third of those suitable for re-use (476 out of 1248) contained drugs in the latest WHO Essential Drugs List. Conclusion: Unused medicines are returned in substantial quantities and have considerable financial value, with many in a condition suitable for re-use. We consider it appropriate to reopen the debate on the potential for re-using these medicines in developing countries where medicines are not widely available and also within the UK. © The Author 2007, Published by Oxford University Press on behalf of Faculty of Public Health. All rights reserved.

The development of a solid waste management strategy

This research is concerned with the application of operational research techniques in the development of a long- term waste management policy by an English waste disposal authority. The main aspects which have been considered are the estimation of future waste production and the assessment of the effects of proposed systems. Only household and commercial wastes have been dealt with in detail, though suggestions are made for the extension of the effect assessment to cover industrial and other wastes. Similarly, the only effects considered in detail have been costs, but possible extensions are discussed. An important feature of the study is that it was conducted in close collaboration with a waste disposal authority, and so pays more attention to the actual needs of the authority than is usual in such research. A critical examination of previous waste forecasting work leads to the use of simple trend extrapolation methods, with some consideration of seasonal effects. The possibility of relating waste production to other social and economic indicators is discussed. It is concluded that, at present, large uncertainties in predictions are inevitable; waste management systems must therefore be designed to cope with this uncertainty. Linear programming is used to assess the overall costs of proposals. Two alternative linear programming formulations of this problem are used and discussed. The first is a straightforward approach, which has been .implemented as an interactive computer program. The second is more sophisticated and represents the behaviour of incineration plants more realistically. Careful attention is paid to the choice of appropriate data and the interpretation of the results. Recommendations are made on methods for immediate use, on the choice of data to be collected for future plans, and on the most useful lines for further research and development.

A legal perspective of integrated surface mining, solid waste landfill reclamation and land conservation

In the area of international environmental law this thesis proposes the formulation of one-step planning and permitting regulation for the integrated utilisation of new surface mines as depositories for municipal solid waste. Additionally, the utilisation of abandoned and currently operated surface mines is proposed as solid waste landfills as an integral step in their reclamation. Existing laws, litigation and issues in the United Kingdom, the U.S. and Canada are discussed because of their common legal system, language and heritage. The critical shortage of approved space for disposal of solid waste has caused an urgent and growing problem for both the waste disposal industry and society. Surface mining can serve three important environmental and societal functions inuring to the health and welfare of the public: (1) providing basic minerals for goods and construction; (20 sequentially, to provide critically needed, safe burial sites for society's wastes, and (3) to conserve land by dual purpose use and to restore derelict land to beneficial surface use. Currently, the first two functions are treated environmentally, and in regulation, as two different siting problems, yet they both are earth-disturbing and excavating industries requiring surface restoration. The processes are largely duplicative and should be combined for better efficiency, less earth disturbance, conservation of land, and for fuller and better reclamation of completed surface mines returning the surfaces to greater utility than present mined land reclamation procedures. While both industries are viewed by a developed society and its communities as "bad neighbours", they remain essential and critical for mankind's existence and welfare. The study offers successful examples of the integrated process in each country. The study argues that most non-fuel surface mine openings, if not already safe, can economically, through present containment technology, be made environmentally safe for use as solid waste landfills. Simultaneously, the procedure safeguards and monitors protection of ground and surface waters from landfill contamination.

Waste to power

ABSTRACT: There has been a growing trend towards the use of biomass as a primary energy source, which now contributes over 54% of the European pulp and paper industry energy needs [1]. The remaining part comes from natural gas, which to a large extent serves as the major source of energy for numerous recovered fiber paper mills located in regions with limited available forest resources. The cost of producing electricity to drive paper machinery and generate heat for steam is increasing as world demand for fossil fuels increases. Additionally, recovered fiber paper mills are also significant producers of fibrous sludge and reject waste material that can contain high amounts of useful energy. Currently, a majority of these waste fractions is disposed of by landspreading, incineration, or landfill. Paper mills must also pay a gate fee to process their waste streams in this way and the result of this is a further increase in operating costs. This work has developed methods to utilize the waste fractions produced at recovered fiber paper mills for the onsite production of combined heat and power (CHP) using advanced thermal conversion methods (pyrolysis and gasification) that are well suited to relatively small scales of throughput. The electrical power created would either be used onsite to power the paper making process or alternatively exported to the national grid, and the surplus heat created could also be used onsite or exported to a local customer. The focus of this paper is to give a general overview of the project progress so far and will present the experimental results of the most successful thermal conversion trials carried out by this work to date. Application: The research provides both paper mills and energy providers with methodologies to condition their waste materials for conversion into useful energy. The research also opens up new markets for gasifier and pyrolysis equipment manufacturers and suppliers.

Waste 4:electronic-scrap recycling

The Haloclean process, a rotary kiln process for pyrolysis, developed by researchers at the Forschungszentrum Karlsruhe, Germany makes it possible to recover copper and precious metals from the scrap, ready for recycling. Pyrolysis neatly turns brominated electronic scrap plastics into recyclable copper and methanol feedstock while removing the halogens. The process has demonstrated its ability to recycle brominated electronic scrap in extensive parametric studies. A method suitable for the selective production of HBr in the presence of chlorine is the treatment of the pyrolysis oils with molten polypropylene. This treatment is offers the possibility to use the gas and liquid fraction from pyrolysis of electronic scrap as fossil fuel substitute in copper smelter processes or as feedstock for methanol production via gasification.

Design, synthesis and RAFT polymerisation of a quinoline-based monomer for use in metal-binding composite microfibres

Metal-binding polymer fibres have attracted major attention for diverse applications in membranes for metal sequestration from waste waters, non-woven wound dressings, matrices for photocatalysis, and many more. This paper reports the design and synthesis of an 8-hydroxyquinoline-based zinc-binding styrenic monomer, QuiBoc. Its subsequent polymerisation by reversible addition–fragmentation chain transfer (RAFT) yielded well-defined polymers, PQuiBoc, of controllable molar masses (6 and 12 kg mol−1) with low dispersities (Đ, Mw/Mn < 1.3). Protected (PQuiBoc) and deprotected (PQuiOH) derivatives of the polymer exhibited a high zinc-binding capacity, as determined by semi-quantitative SEM/EDXA analyses, allowing the electrospinning of microfibres from a PQuiBoc/polystyrene (PS) blend without the need for removal of the protecting group. Simple “dip-coating” of the fibrous mats into ZnO suspensions showed that PQuiBoc/PS microfibres with only 20% PQuiBoc content had almost three-fold higher loadings of ZnO (29%) in comparison to neat PS microfibres (11%).

Energy production from biomass and waste derived intermediate pyrolysis oils

This study investigates the use of Pyroformer intermediate pyrolysis system to produce alternative diesel engines fuels (pyrolysis oil) from various biomass and waste feedstocks and the application of these pyrolysis oils in a diesel engine generating system for Combined Heat and Power (CHP) production. The pyrolysis oils were produced in a pilot-scale (20 kg/h) intermediate pyrolysis system. Comprehensive characterisations, with a view to use as engine fuels, were carried out on the sewage sludge and de-inking sludge derived pyrolysis oils. They were both found to be able to provide sufficient heat for fuelling a diesel engine. The pyrolysis oils also presented poor combustibility and high carbon deposition, but these problems could be mitigated by means of blending the pyrolysis oils with biodiesel (derived from waste cooking oil). The blends of SSPO (sewage sludge pyrolysis oil) and biodiesel (30/70 and 50/50 in volumetric ratios) were tested in a 15 kWe Lister type stationary generating system for up to 10 hours. There was no apparent deterioration observed in engine operation. With 30% SSPO blended into biodiesel, the engine presents better overall performance (electric efficiency), fuel consumption, and overall exhaust emissions than with 50% SSPO blend. An overall system analysis was carried out on a proposed integrated Pyroformer-CHP system. Combined with real experimental results, this was used for evaluating the costs for producing heat and power and char from wood pellets and sewage sludge. It is concluded that the overall system efficiencies for both types of plant can be over 40%; however the integrated CHP system is not economically viable. This is due to extraordinary project capital investment required.

Estimation of computer waste quantities using forecasting techniques

Technology changes rapidly over years providing continuously more options for computer alternatives and making life easier for economic, intra-relation or any other transactions. However, the introduction of new technology “pushes” old Information and Communication Technology (ICT) products to non-use. E-waste is defined as the quantities of ICT products which are not in use and is bivariate function of the sold quantities, and the probability that specific computers quantity will be regarded as obsolete. In this paper, an e-waste generation model is presented, which is applied to the following regions: Western and Eastern Europe, Asia/Pacific, Japan/Australia/New Zealand, North and South America. Furthermore, cumulative computer sales were retrieved for selected countries of the regions so as to compute obsolete computer quantities. In order to provide robust results for the forecasted quantities, a selection of forecasting models, namely (i) Bass, (ii) Gompertz, (iii) Logistic, (iv) Trend model, (v) Level model, (vi) AutoRegressive Moving Average (ARMA), and (vii) Exponential Smoothing were applied, depicting for each country that model which would provide better results in terms of minimum error indices (Mean Absolute Error and Mean Square Error) for the in-sample estimation. As new technology does not diffuse in all the regions of the world with the same speed due to different socio-economic factors, the lifespan distribution, which provides the probability of a certain quantity of computers to be considered as obsolete, is not adequately modeled in the literature. The time horizon for the forecasted quantities is 2014-2030, while the results show a very sharp increase in the USA and United Kingdom, due to the fact of decreasing computer lifespan and increasing sales.

Combustion and emission characteristics of a typical biodiesel engine operated on waste cooking oil derived biodiesel

Waste cooking oils can be converted into fuels to provide economical and environmental benefits. One option is to use such fuels in stationary engines for electricity generation, co-generation or tri-generation application. In this study, biodiesel derived from waste cooking oil was tested in an indirect injection type 3-cylinder Lister Petter biodiesel engine. We compared the combustion and emission characteristics with that of fossil diesel operation. The physical and chemical properties of pure biodiesel (B100) and its blends (20% and 60% vol.) were measured and compared with those of diesel. With pure biodiesel fuel, full engine power was achieved and the cylinder gas pressure diagram showed stable operation. At full load, peak cylinder pressure of B100 operation was almost similar to diesel and peak burn rate of combustion was about 13% higher than diesel. For biodiesel operation, occurrences of peak burn rates were delayed compared to diesel. Fuel line injection pressure was increased by 8.5-14.5% at all loads. In comparison to diesel, the start of combustion was delayed and 90% combustion occurred earlier. At full load, the total combustion duration of B100 operation was almost 16% lower than diesel. Biodiesel exhaust gas emissions contained 3% higher CO2 and 4% lower NOx, as compared to diesel. CO emissions were similar at low load condition, but were decreased by 15 times at full load. Oxygen emission decreased by around 1.5%. Exhaust gas temperatures were almost similar for both biodiesel and diesel operation. At full engine load, the brake specific fuel consumption (on a volume basis) and brake thermal efficiency were respectively about 2.5% and 5% higher compared to diesel. Full engine power was achieved with both blends, and little difference in engine performance and emission results were observed between 20% and 60% blends. The study concludes that biodiesel derived from waste cooking oil gave better efficiency and lower NOx emissions than standard diesel. Copyright © 2012 SAE International.

WASAN : the development of a facilitated methodology for structuring a waste minimisation problem

This paper contributes a new methodology called Waste And Source-matter ANalyses (WASAN) which supports a group in building agreeable actions for safely minimising avoidable waste. WASAN integrates influences from the Operational Research (OR) methodologies/philosophies of Problem Structuring Methods, Systems Thinking, simulation modelling and sensitivity analysis as well as industry approaches of Waste Management Hierarchy, Hazard Operability (HAZOP) Studies and As Low As Reasonably Practicable (ALARP). The paper shows how these influences are compiled into facilitative structures that support managers in developing recommendations on how to reduce avoidable waste production. WASAN is being designed as Health and Safety Executive Guidance on what constitutes good decision making practice for the companies that manage nuclear sites. In this paper we report and reflect on its use in two soft OR/problem structuring workshops conducted on radioactive waste in the nuclear industry. Crown Copyright © 2010.