Single uniform FBG for simultaneous measurement of liquid level and temperature

In this paper, we propose and demonstrate a novel scheme for simultaneous measurement of liquid level and temperature based on a simple uniform fiber Bragg grating (FBG) by monitoring both the short-wavelength-loss peaks and its Bragg resonance. The liquid level can be measured from the amplitude changes of the short-wavelength-loss peaks, while temperature can be measured from the wavelength shift of the Bragg resonance. Both theoretical simulation results and experimental results are presented. Such a scheme has some advantages including robustness, simplicity, flexibility in choosing sensitivity and simultaneous temperature measurement capability.

Evaluation of RF power degradation in microwave photonic systems employing uniform period fibre Bragg gratings

The frequency dependent RF power degradation in direct modulated microwave photonic systems employing uniform period fibre Bragg gratingsFBG.as reflective elements is investigated. The results have implications in terms of the available RF bandwidth and the stability requirements for the fibre Bragg gratings.

Transmission of non-uniform OTDM channels in nonlinearly-guided dispersion-managed fibre system

The effects of channel inequality on nonlinear signal switching in a nonlinear optical fiber loop mirror (NOLM) were investigated. It was found that the channel-to-channel amplitude differences in optical time division multiplexing (OTDM) have strong impact on swiching behavior of individual channels in a 2R regenerator. The optical pulses in different channels face either suppression of the amplitude noise or increase in noise, depending on the inter-channel amplitude difference. It was stated that appropriate control of the channel uniformity in the OTDM transmitters is required to support stable long-haul transmission in 2R regenerated systems.

A theoretical investigation into the ultimate strength in bending and torsion of plain and reinforced concrete members

Presented in this thesis are original theoretical solutions for the determination of the ultimate strength in bending and torsion for: a) Plain concrete members. (b) Concrete members reinforced with longitudinal steel only. (c) Concrete members reinforced with longitudinal and transverse steel at yield. (d) Concrete members reinforced with longitudinal and transverse steel, where partial yielding and non yielding occurs. The theories are compared with available experimental results and show reasonable agreement.

Sparse signal representation by adaptive non-uniform B-spline dictionaries on a compact interval

Non-uniform B-spline dictionaries on a compact interval are discussed in the context of sparse signal representation. For each given partition, dictionaries of B-spline functions for the corresponding spline space are built up by dividing the partition into subpartitions and joining together the bases for the concomitant subspaces. The resulting slightly redundant dictionaries are composed of B-spline functions of broader support than those corresponding to the B-spline basis for the identical space. Such dictionaries are meant to assist in the construction of adaptive sparse signal representation through a combination of stepwise optimal greedy techniques.

On the boundedness of the SORM DEA models with negative data

Emrouznejad et al. (2010) proposed a Semi-Oriented Radial Measure (SORM) model for assessing the efficiency of Decision Making Units (DMUs) by Data Envelopment Analysis (DEA) with negative data. This paper provides a necessary and sufficient condition for boundedness of the input and output oriented SORM models.

The practical ultimate strength design of reinforced concrete frameworks

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Single uniform FBG for simultaneous measurement of liquid level and temperature

In this paper, we propose and demonstrate a novel scheme for simultaneous measurement of liquid level and temperature based on a simple uniform fiber Bragg grating (FBG) by monitoring both the short-wavelength-loss peaks and its Bragg resonance. The liquid level can be measured from the amplitude changes of the short-wavelength-loss peaks, while temperature can be measured from the wavelength shift of the Bragg resonance. Both theoretical simulation results and experimental results are presented. Such a scheme has some advantages including robustness, simplicity, flexibility in choosing sensitivity and simultaneous temperature measurement capability.

Impact of design of sharp non-uniform fibre Bragg gratings on system performance

The impact of design of sharp non-uniform fiber Bragg gratings on system performance was presented. The evolution of the Q-value of the worst channel against the propagation distance was shown. The results suggested that to apply approximated flat-dispersion gratings as inline filters in a periodic system, some post-compensation was included to account for the extra dispersion introduced by the gratings.

Random distributed feedback fiber laser of ultimate efficiency

We demonstrate a random fiber laser of ultimate efficiency. More than 2 Watts are generated from 0.5W of pump excess over the generation threshold. At higher power, an optical efficiency corresponds to the quantum limit.

Evaluation of RF power degradation in microwave photonic systems employing uniform period fibre Bragg gratings

The frequency dependent radio frequency power degradation in direct modulated microwave photonic systems employing uniform period fiber Bragg gratings (FBG) as reflective elements in investigated. Results show implications in terms of the available radio frequency bandwidth and the stability requirements for the FBG.

Cost-reduction using non-uniform traffic in optical networks

Next-generation networks are likely to be non-uniform in all their aspects, including number of lightpaths carried per link, number of wavelengths per link, number of fibres per link, asymmetry of the links, and traffic flows. Routing and wavelength allocation models generally assume that the optical network is uniform and that the number of wavelengths per link is a constant. In practice however, some nodes and links carry heavy traffic and additional wavelengths are needed in those links. We study a wavelength-routed optical network based on the UK JANET topology where traffic demands between nodes are assumed to be non-uniform. We investigate how network capacity can be increased by locating congested links and suggesting cost-effective upgrades. Different traffic demands patterns, hop distances, number of wavelengths per link, and routing algorithms are considered. Numerical results show that a 95% increase in network capacity is possible by overlaying fibre on just 5% of existing links. We conclude that non-uniform traffic allocation can be beneficial to localize traffic in nodes and links deep in the network core and provisioning of additional resources there can efficiently and cost-effectively increase network capacity. © 2013 IEEE.