The steady performance of a porous and compliant aerostatic thrust bearing

Recent developments in aerostatic thrust bearings have included: (a) the porous aerostatic thrust bearing containing a porous pad and (b) the inherently compensated compliant surface aerostatic thrust bearing containing a thin elastomer layer. Both these developments have been reported to improve the bearing load capacity compared to conventional aerostatic thrust bearings with rigid surfaces. This development is carried one stage further in a porous and compliant aerostatic thrust bearing incorporating both a porous pad and an opposing compliant surface. The thin elastomer layer forming the compliant surface is bonded to a rigid backing and is of a soft rubber like material. Such a bearing is studied experimentally and theoretically under steady state operating conditions. A mathematical model is presented to predict the bearing performance. In this model is a simplified solution to the elasticity equations for deflections of the compliant surface. Account is also taken of deflections in the porous pad due to the pressure difference across its thickness. The lubrication equations for flow in the porous pad and bearing clearance are solved by numerical finite difference methods. An iteration procedure is used to couple deflections of the compliant surface and porous pad with solutions to the lubrication equations. Comparisons between experimental results and theoretically predicted bearing performance are in good agreement. However these results show that the porous and compliant aerostatic thrust bearing performance is lower than that of a porous aerostatic thrust bearing with a rigid surface in place of the compliant surface. This discovery is accounted to the recess formed in the bearing clearance by deflections of the compliant surface and its effect on flow through the porous pad.

Effect of fluid contaminant on the behaviour of a hydrostatic thrust bearing

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Splines and vector splines

The thrust of this report concerns spline theory and some of the background to spline theory and follows the development in (Wahba, 1991). We also review methods for determining hyper-parameters, such as the smoothing parameter, by Generalised Cross Validation. Splines have an advantage over Gaussian Process based procedures in that we can readily impose atmospherically sensible smoothness constraints and maintain computational efficiency. Vector splines enable us to penalise gradients of vorticity and divergence in wind fields. Two similar techniques are summarised and improvements based on robust error functions and restricted numbers of basis functions given. A final, brief discussion of the application of vector splines to the problem of scatterometer data assimilation highlights the problems of ambiguous solutions.

The missing ingredient:inter-municipal cooperation and central-local relations in the UK

The thrust of the argument presented in this chapter is that inter-municipal cooperation (IMC) in the United Kingdom reflects local government's constitutional position and its exposure to the exigencies of Westminster (elected central government) and Whitehall (centre of the professional civil service that services central government). For the most part councils are without general powers of competence and are restricted in what they can do by Parliament. This suggests that the capacity for locally driven IMC is restricted and operates principally within a framework constructed by central government's policy objectives and legislation and the political expediencies of the governing political party. In practice, however, recent examples of IMC demonstrate that the practices are more complex than this initial analysis suggests. Central government may exert top-down pressures and impose hierarchical directives, but there are important countervailing forces. Constitutional changes in Scotland and Wales have shifted the locus of central- local relations away from Westminster and Whitehall. In England, the seeding of English government regional offices in 1994 has evolved into an important structural arrangement that encourages councils to work together. Within the local government community there is now widespread acknowledgement that to achieve the ambitious targets set by central government, councils are, by necessity, bound to cooperate and work with other agencies. In recent years, the fragmentation of public service delivery has affected the scope of IMC. Elected local government in the UK is now only one piece of a complex jigsaw of agencies that provides services to the public; whether it is with non-elected bodies, such as health authorities, public protection authorities (police and fire), voluntary nonprofit organisations or for-profit bodies, councils are expected to cooperate widely with agencies in their localities. Indeed, for projects such as regeneration and community renewal, councils may act as the coordinating agency but the success of such projects is measured by collaboration and partnership working (Davies 2002). To place these developments in context, IMC is an example of how, in spite of the fragmentation of traditional forms of government, councils work with other public service agencies and other councils through the medium of interagency partnerships, collaboration between organisations and a mixed economy of service providers. Such an analysis suggests that, following changes to the system of local government, contemporary forms of IMC are less dependent on vertical arrangements (top-down direction from central government) as they are replaced by horizontal modes (expansion of networks and partnership arrangements). Evidence suggests, however that central government continues to steer local authorities through the agency of inspectorates and regulatory bodies, and through policy initiatives, such as local strategic partnerships and local area agreements (Kelly 2006), thus questioning whether, in the case of UK local government, the shift from hierarchy to network and market solutions is less differentiated and transformation less complete than some literature suggests. Vertical or horizontal pressures may promote IMC, yet similar drivers may deter collaboration between local authorities. An example of negative vertical pressure was central government's change of the systems of local taxation during the 1980s. The new taxation regime replaced a tax on property with a tax on individual residency. Although the community charge lasted only a few years, it was a highpoint of the then Conservative government policy that encouraged councils to compete with each other on the basis of the level of local taxation. In practice, however, the complexity of local government funding in the UK rendered worthless any meaningful ambition of councils competing with each other, especially as central government granting to local authorities is predicated (however imperfectly) on at least notional equalisation between those areas with lower tax yields and the more prosperous locations. Horizontal pressures comprise factors such as planning decisions. Over the last quarter century, councils have competed on the granting of permission to out-of-town retail and leisure complexes, now recognised as detrimental to neighbouring authorities because economic forces prevail and local, independent shops are unable to compete with multiple companies. These examples illustrate tensions at the core of the UK polity of whether IMC is feasible when competition between local authorities heightened by local differences reduces opportunities for collaboration. An alternative perspective on IMC is to explore whether specific purposes or functions promote or restrict it. Whether in the principle areas of local government responsibilities relating to social welfare, development and maintenance of the local infrastructure or environmental matters, there are examples of IMC. But opportunities have diminished considerably as councils lost responsibility for services provision as a result of privatisation and transfer of powers to new government agencies or to central government. Over the last twenty years councils have lost their role in the provision of further-or higher-education, public transport and water/sewage. Councils have commissioning power but only a limited presence in providing housing needs, social care and waste management. In other words, as a result of central government policy, there are, in practice, currently far fewer opportunities for councils to cooperate. Since 1997, the New Labour government has promoted IMC through vertical drivers and the development; the operation of these policy initiatives is discussed following the framework of the editors. Current examples of IMC are notable for being driven by higher tiers of government, working with subordinate authorities in principal-agent relations. Collaboration between local authorities and intra-interand cross-sectoral partnerships are initiated by central government. In other words, IMC is shaped by hierarchical drivers from higher levels of government but, in practice, is locally varied and determined less by formula than by necessity and function. © 2007 Springer.

Dissociating the spatio-temporal characteristics of cortical neuronal activity associated with human volitional swallowing in the healthy adult brain

Human swallowing represents a complex highly coordinated sensorimotor function whose functional neuroanatomy remains incompletely understood. Specifically, previous studies have failed to delineate the temporo-spatial sequence of those cerebral loci active during the differing phases of swallowing. We therefore sought to define the temporal characteristics of cortical activity associated with human swallowing behaviour using a novel application of magnetoencephalography (MEG). In healthy volunteers (n = 8, aged 28-45), 151-channel whole cortex MEG was recorded during the conditions of oral water infusion, volitional wet swallowing (5 ml bolus), tongue thrust or rest. Each condition lasted for 5 s and was repeated 20 times. Synthetic aperture magnetometry (SAM) analysis was performed on each active epoch and compared to rest. Temporal sequencing of brain activations utilised time-frequency wavelet plots of regions selected using virtual electrodes. Following SAM analysis, water infusion preferentially activated the caudolateral sensorimotor cortex, whereas during volitional swallowing and tongue movement, the superior sensorimotor cortex was more strongly active. Time-frequency wavelet analysis indicated that sensory input from the tongue simultaneously activated caudolateral sensorimotor and primary gustatory cortex, which appeared to prime the superior sensory and motor cortical areas, involved in the volitional phase of swallowing. Our data support the existence of a temporal synchrony across the whole cortical swallowing network, with sensory input from the tongue being critical. Thus, the ability to non-invasively image this network, with intra-individual and high temporal resolution, provides new insights into the brain processing of human swallowing. © 2004 Elsevier Inc. All rights reserved.

Neural network control of a gas turbine

In this paper we explore the practical use of neural networks for controlling complex non-linear systems. The system used to demonstrate this approach is a simulation of a gas turbine engine typical of those used to power commercial aircraft. The novelty of the work lies in the requirement for multiple controllers which are used to maintain system variables in safe operating regions as well as governing the engine thrust.

Exporting and productivity in business services:evidence from the United States

Does exporting make firms more productive, or do more productive firms choose to become exporters? Given the amount of resources devoted by governments to supporting exporters, this is an important question. There are reasons to expect exporting to boost productivity, both through the exposure to foreign competition which exporting brings, and through ‘learning by exporting’. However, the broad thrust of previous research is that more productive firms self-select into export markets, with relatively little evidence that exporting leads to higher productivity thereafter. This paper considers the link between exporting and productivity for a sample of firms in US business services. We find that larger, more productive firms are more likely to become exporters, but that these factors do not necessarily influence the extent of exporting. This conforms with previous literature that there is a self-selection effect into exporting. We then test for the effect of exporting on productivity levels after allowing for this selection effect. We model both the relationship between exporting and productivity, and a simultaneous relationship between export intensity and productivity after allowing for selection bias. In both cases we find a clear association, indicating that productivity is positively linked both to exporting and to increased exposure to international markets.

The influence of tool geometry on the performance of drilling tools

The main objective of the work presented in this thesis is to investigate the two sides of the flute, the face and the heel of a twist drill. The flute face was designed to yield straight diametral lips which could be extended to eliminate the chisel edge, and consequently a single cutting edge will be obtained. Since drill rigidity and space for chip conveyance have to be a compromise a theoretical expression is deduced which enables optimum chip disposal capacity to be described in terms of drill parameters. This expression is used to describe the flute heel side. Another main objective is to study the effect on drill performance of changing the conventional drill flute. Drills were manufactured according to the new flute design. Tests were run in order to compare the performance of a conventional flute drill and non conventional design put forward. The results showed that 50% reduction in thrust force and approximately 18% reduction in torque were attained for the new design. The flank wear was measured at the outer corner and found to be less for the new design drill than for the conventional one in the majority of cases. Hole quality, roundness, size and roughness were also considered as a further aspect of drill performance. Improvement in hole quality is shown to arise under certain cutting conditions. Accordingly it might be possible to use a hole which is produced in one pass of the new drill which previously would have required a drilled and reamed hole. A subsidiary objective is to design the form milling cutter that should be employed for milling the foregoing special flute from drill blank allowing for the interference effect. A mathematical analysis in conjunction with computing technique and computers is used. To control the grinding parameter, a prototype drill grinder was designed and built upon the framework of an existing cincinnati cutter grinder. The design and build of the new grinder is based on a computer aided drill point geometry analysis. In addition to the conical grinding concept, the new grinder is also used to produce spherical point utilizing a computer aided drill point geometry analysis.

Some aspects of drill performance

High speed twist drills are probably the most common of all metal cutting tools and also the least efficient. In this study, detailed research was undertaken into aspects of drill performance and ways in which drilling could be improved in short hole depths of up to two diameters. The work included an evaluation of twist drill geometry and grinding parameters. It was established that errors in point grinding lead to increased hole oversize and reduced drill life. A fundamental analysis was made to establish predictive equations for the drill torque and thrust using modified orthogonal cutting equations and empirical data. A good correlation was obtained between actual and predicted results. Two new techniques for extending twist drill life by the use of coolant feeding holes and also the application of titanium nitride coatings were evaluated. Both methods were found to have potential for improving drill performance. A completely new design of carbide tipped drill was designed and developed. The new design was tested and it compared favourably with two commercially available carbide tipped drills. In further work an entirely different type of drill point geometry was developed for the drill screw. A new design was produced which enabled the drilling time to be minimised for the low thrust forces that were likely to be used with hand held power tools.

Deep hole drilling with twist drills: aspects of the CNC process and its real time monitoring and adaptive control

Deep hole drilling is one of the most complicated metal cutting processes and one of the most difficult to perform on CNC machine-tools or machining centres under conditions of limited manpower or unmanned operation. This research work investigates aspects of the deep hole drilling process with small diameter twist drills and presents a prototype system for real time process monitoring and adaptive control; two main research objectives are fulfilled in particular : First objective is the experimental investigation of the mechanics of the deep hole drilling process, using twist drills without internal coolant supply, in the range of diarneters Ø 2.4 to Ø4.5 mm and working length up to 40 diameters. The definition of the problems associated with the low strength of these tools and the study of mechanisms of catastrophic failure which manifest themselves well before and along with the classic mechanism of tool wear. The relationships between drilling thrust and torque with the depth of penetration and the various machining conditions are also investigated and the experimental evidence suggests that the process is inherently unstable at depths beyond a few diameters. Second objective is the design and implementation of a system for intelligent CNC deep hole drilling, the main task of which is to ensure integrity of the process and the safety of the tool and the workpiece. This task is achieved by means of interfacing the CNC system of the machine tool to an external computer which performs the following functions: On-line monitoring of the drilling thrust and torque, adaptive control of feed rate, spindle speed and tool penetration (Z-axis), indirect monitoring of tool wear by pattern recognition of variations of the drilling thrust with cumulative cutting time and drilled depth, operation as a data base for tools and workpieces and finally issuing of alarms and diagnostic messages.

The effect of elevated temperature on the wear of stainless steel in contact with tungsten carbide

The bearings in the air motors of modern jet aircraft engines must operate dry in hostile conditions at temperatures up to 500° C, where the thrust races in the actuators operate at temperatures up to 300° C. One of the few metallurgical combinations which can function efficiently under these conditions is martensitic stainless steel on tungsten carbide. The work described was initiated to isolate the wear mechanisms of two such steels in contact with tungsten carbide at temperatures up to 500° C. Experiments were carried out on angular contact bearings similar to these used in service, where both rolling and sliding is present and also for pure sliding conditions using a pin-on-disc apparatus. Wear measurements of the bearings were obtained with wear rates, friction and surface temperatures from the pin-on-disc machine for a series of loads and speeds. Extensive X-ray diffraction analysis was carried out on the wear debris, with also S.E.M. analysis and hardness tests on the worn surfaces along with profilometry measurements of the disc. The oxidational parameters of the steel were obtained from measurements of oxide growth rates by ellipsometry. Three distinct mechanisms of wear were established and the latter two were found to be present in both configurations. These involve an oxidational-abrasive mechanism at loads below 40 N with pin surface temperatures up to about 300 °C, with the mechanism changing to severe wear for higher loads. As the temperature increases a third wear mechanism appears due to transfer of relatively soft oxide films to the steel surface reducing the wear rate. Theoretical K factors were derived and compared with experimental values which were found to be in good agreement for the severe wear mechanism. The pin-on-disc experiments may be useful as a screening test for material selection, without the considerable cost of producing the angular contact bearings.

Mesozoic to recent evolution of the Andean forearc of northern Chile (22-24 s)

The Andean forearc of northern Chile comprises four morphotectonic units, which include from east to west: 1) The Cordillera de la Costa: composed of Jurassic granites and andesites, thought to represent a volcanic arc, the Mejillones terrane, an accreted allochthonous terrane, and the Lower Cretaceous Coloso basin, which formed through forearc extension along the suture between the Mejillones terrane and the Jurassic arc. Palaeomagnetic studies of the above units have identified approximately 29+/-11 degrees of clockwise rotation. Rotation is due to extension (caused by subduction roll back and slab pull), at an angle to the direction of absolute motion of the South American Plate. 2) The Central Depression: a large arid basin containing isolated fault-bounded blocks of pre-Mesozoic metamorphosed igneous rocks, Triassic sediments and volcanics, and Jurassic carbonates, deposited in a. back-arc basin setting. The isolated blocks formed through extension along previous thrust faults, these originated through compression of the back-arc basin due to accretion of the Jurassic volcanic arc. 3) The Precordillera.: composed of Permian-Triassic rift-related sediments and volcanics, Jurassic continental sediments synchronous with back-arc basin sedimentation, and Cretaceous and Oligo-Miocene continental sediments deposited in foreland basins. Palaeomagnetism has identified clockwise rotation in rocks ranging in age from Jurassic-Miocene. Rotation in the Precordillera. affected larger structural blocks than in the Cordillera de la Costa. 4) The Salar Depression: a. series of arid continental basins developed on continental crust. These basins nay have originated in the Triassic, when rifting of the South American craton is thought to have taken place. In conclusion, palaeomagnetic and geological evidence is consistent with the view that the north Chilean forearc was largely under an extensional stress regime. However, the presence of extensive compressional structures in Palaeocene and older rocks in the forearc together with the currently active foreland thrust belt of Argentina. indicate that throughout the evolution of the Andean Orogen, a delicate balance between compressional and extensional tectonic regimes has existed.