Impact of liberalization on efficiency and productivity of sugar industry in Kenya

Purpose – The data used in this study is for the period 1980-2000. Almost midway through this period (in 1992), the Kenyan government liberalized the sugar industry and the role of the market increased, while the government's role with respect to control of prices, imports and other aspects in the sector declined. This exposed the local sugar manufacturers to external competition from other sugar producers, especially from the COMESA region. This study aims to find whether there were any changes in efficiency of production between the two periods (pre and post-liberalization). Design/methodology/approach – The study utilized two methodologies to efficiency estimation: data envelopment analysis (DEA) and the stochastic frontier. DEA uses mathematical programming techniques and does not impose any functional form on the data. However, it attributes all deviation from the mean function to inefficiencies. The stochastic frontier utilizes econometric techniques. Findings – The test for structural differences in the two periods does not show any statistically significant differences between the two periods. However, both methodologies show a decline in efficiency levels from 1992, with the lowest period experienced in 1998. From then on, efficiency levels began to increase. Originality/value – To the best of the authors' knowledge, this is the first paper to use both methodologies in the sugar industry in Kenya. It is shown that in industries where the noise (error) term is minimal (such as manufacturing), the DEA and stochastic frontier give similar results.

Variable impedance bearings for large rotating machinery

This thesis describes an investigation which was carried out under the Interdisciplinary Higher Degres (IHD) Scheme of The University of Aston in Birmingham. The investigation, which involved joint collaboration between the IHD scheme, the Department of Mechanical Engineering, and G.E.C. Turbine Generators Limited, was concerned with hydrostatic bearing characteristics and of how hydrostatic bearings could be used to enable turbine generator rotor support impedances to be controlled to give an improved rotor dynamic response. Turbine generator rotor critical speeds are determined not only by the mass and flexibility of the rotor itself, which are relatively easily predicted, but also by the dynamic characteristics of the bearing oil film, pedestal, and foundations. It is because of the difficulty in accurately predicting the rotor support characteristics that the designer has a problem in ensuring that a rotor's normal running speed is not close to one of its critical speeds. The consequence of this situation is that some rotors do have critical speeds close to their normal running speed and the resulting high levels of vibration cause noise, high rotor stresses, and a shortening of bearing life. A combined theoretical and experimental investigation of the effects of mounting the normal rotor journal bearing in a hydrostatic bearing was carried out. The purpose of the work was to show that by changing the oil flow resistance offered by capillaries connecting accumulators to the hydrostatic bearing, the overall rotor support characteristics could be tuned to enable rotor critical speeds to be moved at will. Testing of a combined journal and hydrostatic bearing has confirmed the theory of its operation and a theoretical study of a full size machine showed that its critical speed could be moved by over 350 rpm and that its rotor vibration at running speed could be reduced by 80%.

The impact of NC machinery upon manufacturing industry

The changing face of industry due to the adoption of `New Technology' is briefly discussed, as are the corresponding structural changes in the workforce. The adoption of NC machinery is identified as one of the major innovations affecting the structure of industry. The development of NC machinery, and of relevant programming techniques are reviewed, and the problems arising from its initial sponsorship by the aerospace industry are highlighted. The process of its subsequent diffusion into industry is reviewed. Skill levels adopted for NC use in Britain and Germany are discussed, and analysed to create a structural pattern. These classifications of skill levels are then used to examine the organisational structures adopted by companies utilising NC machines. The greater use made of higher level shop floor skills by German companies is discussed. The results of two surveys of the use made of NC by companies in the North East of England are presented. Effective company organisation for NC use is described, and lack of foresight is shown to lead to vulnerability problems where skills can become concentrated in a few key people. This led to closure of a company in one instance. It is shown that small sub-contract companies have adopted a highly skilled shop floor workforce, and that they have survived in the present hostile economic environment, whilst companies who have used NC to de-skill the shop floor contracted dramatically in the same period. The lack of awareness of the potential for reviewing the product design in relation to the flexibility of NC, so leading to reductions in work in progress levels, is highlighted. Recommendations for skill structures appropriate to various sized companies and suitable training programs are presented to ensure that the full potential of NC machinery is achieved.

Flexible high speed machinery

The thesis describes an investigation into methods for the design of flexible high-speed product processing machinery, consisting of independent electromechanically actuated machine functions which operate under software coordination and control. An analysis is made of the elements of traditionally designed cam-actuated, mechanically coupled machinery, so that the operational functions and principal performance limitations of the separate machine elements may be identified. These are then used to define the requirements for independent actuators machinery, with a discussion of how this type of design approach is more suited to modern manufacturing trends. A distributed machine controller topology is developed which is a hybrid of hierarchical and pipeline control. An analysis is made, with the aid of dynamic simulation modelling, which confirms the suitability of the controller for flexible machinery control. The simulations include complex models of multiple independent actuators systems, which enable product flow and failure analyses to be performed. An analysis is made of high performance brushless d.c. servomotors and their suitability for actuating machine motions is assessed. Procedures are developed for the selection of brushless servomotors for intermittent machine motions. An experimental rig is described which has enabled the actuation and control methods developed to be implemented. With reference to this, an evaluation is made of the suitability of the machine design method and a discussion is given of the developments which are necessary for operational independent actuators machinery to be attained.

Ordered mixing of drugs with particulate excipients

A novel direct compression tableting excipient has been made by recrystallisation of lactose. The particles produced had high porosity, high specific surface area and high surface roughness. The resistance to segregation of ordered mixes formed between a model drug; potassium chloride and the excipients recrystallised lactose, spray crystallised maltose-dextrose (Emdexl and a direct compacting sugar (Dipac) was studied using a vibrational segregation model. The highly porous excipients, Emdex and recrystallised lactose formed ordered mixes which did not segregate even at high accelerations and low frequencies whereas the relatively smooth excipient, Dipac, displayed marked segregation in most vibration conditions. The vibrations were related to practical conditions measured in pharmaceutical process machinery. The time required to form an ordered mix was inversely related to the stability of the mix when subjected to vibration. An ultracentrifuge technique was developed to determine the interparticle adhesion forces holding drug and excipient particles together as ordered units. Excipient powders such as Emdex and recrystallised lactose, which formed non-segregating ordered mixes, had high interparticle adhesion forces. Other ordered mixes that segregated when subjected to different vibration conditions were found to have large quantities of weekly-bound drug particles; such mixes included those with Dipac as the carrier excipient as well as those containing a high concentration of drug. The electrostatic properties of different drug and excipient powders were studied using a Faraday well and an electrometer. Excipient powders such as Emdex and recrystallised lactose which formed stable ordered mixes also had a widely different surface charge in comparison with drug particles, whereas Dipac had a similar surface charge to the drug particles and formed unstable ordered mixes. A specially constructed triboelectric charging apparatus based on an air cyclone was developed to increase the affinity of drug particles for different excipient particles. Using triboelectrification to increase the interparticle adhesion forces, the segregation tendencies of unstable ordered mixes were greatly reduced. The stability of ordered mixes is shown to be related to both the surface physical characteristics and the surface electrical properties of the constituent carrier (excipientl particles.

Design methodology for the servo control of high speed multi-axis machinery (BL): decoupling and synchronisation of a generic machine by blockwise decentralised MIMO control

Traditional machinery for manufacturing processes are characterised by actuators powered and co-ordinated by mechanical linkages driven from a central drive. Increasingly, these linkages are replaced by independent electrical drives, each performs a different task and follows a different motion profile, co-ordinated by computers. A design methodology for the servo control of high speed multi-axis machinery is proposed, based on the concept of a highly adaptable generic machine model. In addition to the dynamics of the drives and the loads, the model includes the inherent interactions between the motion axes and thus provides a Multi-Input Multi-Output (MIMO) description. In general, inherent interactions such as structural couplings between groups of motion axes are undesirable and needed to be compensated. On the other hand, imposed interactions such as the synchronisation of different groups of axes are often required. It is recognised that a suitable MIMO controller can simultaneously achieve these objectives and reconciles their potential conflicts. Both analytical and numerical methods for the design of MIMO controllers are investigated. At present, it is not possible to implement high order MIMO controllers for practical reasons. Based on simulations of the generic machine model under full MIMO control, however, it is possible to determine a suitable topology for a blockwise decentralised control scheme. The Block Relative Gain array (BRG) is used to compare the relative strength of closed loop interactions between sub-systems. A number of approaches to the design of the smaller decentralised MIMO controllers for these sub-systems has been investigated. For the purpose of illustration, a benchmark problem based on a 3 axes test rig has been carried through the design cycle to demonstrate the working of the design methodology.

Solid-supported boronic acid conjugates for sugar and glycopeptide recognition

The Fmoc synthetic strategy was employed to synthesise two identical combinatorial peptide libraries on a hydrophilic PEG-PS resin. One library was appended with boronic acid moieties at two positionally-fixed locations. Successful inclusion of the boronic acid units was confirmed using a novel UV fluorescent colorimetric assay employing carminic acid as the dye compound. A study of the effect had by the resin-bound peptides bearing boronic acid groups on the binding characteristics of vancomycin, a medically relevant antibiotic glycoprotein, was conducted. In all, 132 library compounds were tested for their binding affinity with vancomycin, via immobilisation of the glycopeptide onto the solid support through hydrogen bonding or complexation with the boronic acid moieties. Subsequent cleavage via acidolysis afforded vancomycin containing solutions which were quantified by growth inhibition of methicillin susceptible Staphylococcus aureus. Comparison of the diameters of the resultant zones of inhibition and those produced by vancomycin of known concentrations afforded a means of calculating the vancomycin concentration of the cleavage solutions, and thereby determining the binding affinity of vancomycin to each peptide sequence. Five peptide sequences and twenty one of the peptidyl-boronic acid sequences showed zones of inhibition, demonstrating their reversible affinity for vancomycin. Three peptide sequences showed zones of inhibition in both libraries. The presence of boronic acid was therefore shown to impart, enhance, detract and remove the affinity of vancomycin to a range of resin-bound peptide sequences.

Active vibration control at machinery feet

The unmitigated transmission of undesirable vibration can result in problems by way of causing human discomfort, machinery and equipment failure, and affecting the quality of a manufacturing process. When identifiable transmission paths are discernible, vibrations from the source can be isolated from the rest of the system and this prevents or minimises the problems. The approach proposed here for vibration isolation is active force cancellation at points close to the vibration source. It uses force feedback for multiple-input and multiple-output control at the mounting locations. This is particularly attractive for rigid mounting of machine on relative flexible base where machine alignment and motions are to be restricted. The force transfer function matrix is used as a disturbance rejection performance specification for the design of MIMO controllers. For machine soft-mounted via flexible isolators, a model for this matrix has been derived. Under certain conditions, a simple multiplicative uncertainty model is obtained that shows the amount of perturbation a flexible base has on the machine-isolator-rigid base transmissibility matrix. Such a model is very suitable for use with robust control design paradigm. A different model is derived for the machine on hard-mounts without the flexible isolators. With this model, the level of force transmitted from a machine to a final mounting structure using the measurements for the machine running on another mounting structure can be determined. The two mounting structures have dissimilar dynamic characteristics. Experiments have verified the usefulness of the expression. The model compares well with other methods in the literature. The disadvantage lies with the large amount of data that has to be collected. Active force cancellation is demonstrated on an experimental rig using an AC industrial motor hard-mounted onto a relative flexible structure. The force transfer function matrix, determined from measurements, is used to design H and Static Output Feedback controllers. Both types of controllers are stable and robust to modelling errors within the identified frequency range. They reduce the RMS of transmitted force by between 30?80% at all mounting locations for machine running at 1340 rpm. At the rated speed of 1440 rpm only the static gain controller is able to provide 30?55% reduction at all locations. The H controllers on the other hand could only give a small reduction at one mount location. This is due in part to the deficient of the model used in the design. Higher frequency dynamics has been ignored in the model. This can be resolved by the use of a higher order model that can result in a high order controller. A low order static gain controller, with some tuning, performs better. But it lacks the analytical framework for analysis and design.

An investigation into vibration criteria for rotating machinery

Concern had been expressed by engineers of the Shell Chemical Company regarding the validity of existing vibration criteria for rotating machinery. A survey showed that existing criteria were based solely on the amplitude of vibration, normally of the bearing housings, with no allowance being made for the dynamic properties of the support1ng structure. The feasibility of measuring the mechanical impedance of bearing supports in order to assess the severity of vibration generated by a machine has been investigated. It is suggested that in many cases the oscillatory bearing force levels obtained for these measurements will provide a quantitative indication of severity. Theoretical and experimental work has been conducted on a model rig, comprising a flexible shaft running in journal bearings housed in flexible, asymmetric supports. The accuracy with which the system behaviour could be predicted using measured support impedances is discussed together with the extraction of uncoupled support impedances from measurements on the complete rotating system. Access was available to several industrial centrifugal compressors. To enable the bearing support impedances of these machines to be measured on site considerable attention has been paid to the evolution of a technique involving the use of transient excitation. To develop this technique the model rig and a large rotary converter have been used as test structures. Methods have also been devised and developed for the analysis of the transient impedance data.

Biodeterioration of harvested sugar cane in Jamaica

The microbiological, physical and chemical changes which occur instored, harvested sugarcane were studied in Jamaica and the United Kingdom.The degree of deterioration was proportional to time of storage, and wasrevealed by a statistically significant reduction in sucrose content.Other symptoms included a fall in pH, and increases in reducing sugars,dextran, viscosity, and microbial count. Cut cane was universally infectedwith Leuconostoc mesenteroides, which reached a maximum count of 107 to 108organisms per ml. juice within. 3 to 4 days of harvest. Counts of othermicroorganisms were generally insignificant, except for occasional lactobacilli.A new dextran-forming species was named Lactobacillus confusus.Microorganisms isolated from deteriorated cane were screened for theirability to cause deterioration of a sterile, synthetic cane juice. L. mesenteroides strains were the most deteriogenic, but attempts toreproduce the symptoms of "sour" cane by inoculation of this organism intocut cane were only partially successful. L. mesenteroides was present in the soil and the epiphytic flora of the stalk. The principal vector of infection appeared to be the cutters' machete, especially in wet weather. Cane harvested by a chopper machine deteriorated more rapidly than hand-cut whole-stalks. Economic losses due to deterioration of harvested cane were estimated to be 9.2% of the initial recoverable sugar for the 1969 crop at Frome Estate, Jamaica. Dextran content was a useful indicator of cane biodeterioration. The dextran content of mill juices was correlated with rainfall, and significant correlations were obtained between dextran content and viscosity of mill syrups and the amount of sugar lost in final molasses; it also caused the formation of elongated crystals. Attempts to control sour cane by chemical and physical methods were unsuccessful, and it was concluded that the only solution is to mill cane within 24 hours of harvest. A novel method for removal of dextran from mill juices by enzymic treatment with dextranase was developed and patented.

Dynamic response of spring mounted flexible platforms carring rotating machinery

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Analysis of the degree of compliance with the EU Machinery Directive.

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Aggregation and caking processes of granular materials:continuum model and simulation with application to sugar

Aggregation and caking of particles are common severe problems in many operations and processing of granular materials, where granulated sugar is an important example. Prevention of aggregation and caking of granular materials requires a good understanding of moisture migration and caking mechanisms. In this paper, the modeling of solid bridge formation between particles is introduced, based on moisture migration of atmospheric moisture into containers packed with granular materials through vapor evaporation and condensation. A model for the caking process is then developed, based on the growth of liquid bridges (during condensation), and their hardening and subsequent creation of solid bridges (during evaporation). The predicted caking strengths agree well with some available experimental data on granulated sugar under storage conditions.