A study in the application of domestic solar assisted heat pumps for heating and cooling

In the present work, the more important parameters of the heat pump system and of solar assisted heat pump systems were analysed in a quantitative way. Ideal and real Rankine cycles applied to the heat pump, with and without subcooling and superheating were studied using practical recommended values for their thermodynamics parameters. Comparative characteristics of refrigerants here analysed looking for their applicability in heat pumps for domestic heating and their effect in the performance of the system. Curves for the variation of the coefficient of performance as a function of condensing and evaporating temperatures were prepared for R12. Air, water and earth as low-grade heat sources and basic heat pump design factors for integrated heat pumps and thermal stores and for solar assisted heat pump-series, parallel and dual-systems were studied. The analysis of the relative performance of these systems demonstrated that the dual system presents advantages in domestic applications. An account of energy requirements for space and hater heating in the domestic sector in the O.K. is presented. The expected primary energy savings by using heat pumps to provide for the heating demand of the domestic sector was found to be of the order of 7%. The availability of solar energy in the U.K. climatic conditions and the characteristics of the solar radiation here studied. Tables and graphical representations in order to calculate the incident solar radiation over a tilted roof were prepared and are given in this study in section IV. In order to analyse and calculate the heating load for the system, new mathematical and graphical relations were developed in section V. A domestic space and water heating system is described and studied. It comprises three main components: a solar radiation absorber, the normal roof of a house, a split heat pump and a thermal store. A mathematical study of the heat exchange characteristics in the roof structure was done. This permits to evaluate the energy collected by the roof acting as a radiation absorber and its efficiency. An indication of the relative contributions from the three low-grade sources: ambient air, solar boost and heat loss from the house to the roof space during operation is given in section VI, together with the average seasonal performance and the energy saving for a prototype system tested at the University of Aston. The seasonal performance as found to be 2.6 and the energy savings by using the system studied 61%. A new store configuration to reduce wasted heat losses is also discussed in section VI.

Universities Masters World Cup Soccer:integrated sports science research and implementation of an international masters soccer community

Ageing populations with greater wellness and athletic expectations require quality sports and active living experiences in order to increase and sustain participation levels. Responding to the diverse needs and circumstances of Masterslveterans players is a complex and multi-faceted process. While sports science contributions have been very effective at enhancing active living in a variety of youth and adult sports events, very little has been documented regarding their efficacy in events for Masterslveteran players. This paper draws upon action research to examine the growth and development of a unique Masters World Cup 6-0-side Soccer Tournament, involving representative teams from twelve nations. lntegrated sports science concepts and strategies were employed to develop quality soccer experiences. Longitudinal data suggest that fostering a community of practice is critical to the success of Masters soccer programs. In addition to critical leadership contributions, an eclectic range of age-appropriate and responsive soccer experiences are essential to ensure that Masters events meet the diverse needs and circumstances of the players.

Accessibility, deprivation and rural planning policies.

Since the Second World War a range of policies have been implemented by central and local government agencies, with a view to improving accessibility to facilities, housing and employment opportunities within rural areas. It has been suggested that a lack of reasonable access to a range of such facilities and opportunities constitutes a key aspect of deprivation or disadvantage for rural residents. Despite considerable interest, very few attempts have been made to assess the nature and incidence of this disadvantage or the reaction of different sections of the population of rural areas to it. Moreover, almost all previous assessments have relied on so-called 'objective' measures of accessibility and disadvantage and failed to consider the relationship between such measures and 'subjective' measures such as individual perceptions. It is this gap in knowledge that the research described in this thesis has addressed. Following a critical review of relevant literature the thesis describes the way in which data on 'objective' and 'subjective' indicators of accessibility and behavioural responses to accessibility problems was collected, in six case study areas in Shropshire. Analysis of this data indicates that planning and other government policies have failed to significantly improve rural resident's accessibility to their basic requirements, and may in some cases have exacerbated it, and that as a result certain sections of the rural population are relatively disadvantaged. Moreover, analysis shows that .certain aspects of individual subjective' assessments of such accessibility disadvantage are significantly associated with more easily-obtained 'objective' measures. By using discriminant analysis the research demonstrates that it is possible to predict the likely levels of satisfaction with access to facilities from a range of 'objective' measures. The research concludes by highlighting the potential practical applications of such indicators in policy formulation, policy appraisal and policy evaluation.

Melting and solidification of Zinc-Aluminium alloys

Following a scene-setting introduction are detailed reviews of the relevant scientific principles, thermal analysis as a research tool and the development of the zinc-aluminium family of alloys. A recently introduced simultaneous thermal analyser, the STA 1500, its use for differential thermal analysis (DTA) being central to the investigation, is described, together with the sources of support information, chemical analysis, scanning electron microscopy, ingot cooling curves and fluidity spiral castings. The compositions of alloys tested were from the binary zinc-aluminium system, the ternary zinc-aluminium-silicon system at 30%, 50% and 70% aluminium levels, binary and ternary alloys with additions of copper and magnesium to simulate commercial alloys and five widely used commercial alloys. Each alloy was shotted to provide the smaller, 100mg, representative sample required for DTA. The STA 1500 was characterised and calibrated with commercially pure zinc, and an experimental procedure established for the determination of DTA heating curves at 10°C per minute and cooling curves at 2°C per minute. Phase change temperatures were taken from DTA traces, most importantly, liquidus from a cooling curve and solidus from both heating and cooling curves. The accepted zinc-aluminium binary phase diagram was endorsed with the added detail that the eutectic is at 5.2% aluminium rather than 5.0%. The ternary eutectic trough was found to run through the points, 70% Al, 7.1% Si, 545°C; 50% Al, 3.9% Si, 520°C; 30% Al, 1.4% Si, 482°C. The dendrite arm spacing in samples after DTA increased with increasing aluminium content from 130m at 30% to 220m at 70%. The smallest dendrite arm spacing of 60m was in the 30% aluminium 2% silicon alloy. A 1kg ingot of the 10% aluminium binary alloy, insulated with Kaowool, solidified at the same 2°C per minute rate as the DTA samples. A similar sized sand casting was solidified at 3°C per minute and a chill casting at 27°C per minute. During metallographic examination the following features were observed: heavily cored phase which decomposed into ' and '' on cooling; needles of the intermetallic phase FeAl4; copper containing ternary eutectic and copper rich T phase.

Sustainable development, shock and awe? London 2012 and Civil Society

There is a disconnection between the top-down, elite, nature of sports mega-events and the ostensible redistributive and participatory sustainable development agendas staked out by BINGOs (Business-based International Non-Governmental Organizations) such as the contemporary International Olympic Committee (IOC). Focusing specifically on the London 2012 Summer Olympic and Paralympic Games, we argue that, for all the environmental technology advances offered by sports mega-events, their dominant model remains one of a hollowed-out form of sustainable development. Despite significant technical and methodological innovations in environmental stewardship, the development model of the London Olympics remains predicated on the satisfaction of transnational investment flows. We discuss what this means for claims about the staging of a ‘green’ Olympic Games.

A micro industry with closed energy and water cycles for sustainable rural development

Sustainable development requires combining economic viability with energy and environment conservation and ensuring social benefits. It is conceptualized that for designing a micro industry for sustainable rural industrialization, all these aspects should be integrated right up front. The concept includes; (a) utilization of local produce for value addition in a cluster of villages and enhancing income of the target population; (b) use of renewable energy and total utilization of energy generated by co and trigeneration (combining electric power production with heat utilization for heating and cooling); (c) conservation of water and complete recycling of effluents; (d) total utilization of all wastes for achieving closure towards a zero waste system. Enhanced economic viability and sustainability is achieved by integration of appropriate technologies into the industrial complex. To prove the concept, a model Micro Industrial Complex (MIC) has been set up in a semi arid desert region in Rajasthan, India at village Malunga in Jodhpur district. A biomass powered boiler and steam turbine system is used to generate 100-200 KVA of electric power and high energy steam for heating and cooling processes downstream. The unique feature of the equipment is a 100-150 kW back-pressure steam turbine, utilizing 3-4 tph (tonnes per hour) steam, developed by M/s IB Turbo. The biomass boiler raises steam at about 20 barg 3 tph, which is passed through a turbine to yield about 150 kW of electrical power. The steam let out at a back pressure of 1-3 barg has high exergy and this is passed on as thermal energy (about 2 MW), for use in various applications depending on the local produce and resources. The biomass fuel requirement for the boiler is 0.5-0.75 tph depending on its calorific value. In the current model, the electricity produced is used for running an oil expeller to extract castor oil and the castor cake is used as fuel in the boiler. The steam is used in a Multi Effect Distillation (MED) unit for drinking water production and in a Vapour Absorption Machine (VAM) for cooling, for banana ripening application. Additional steam is available for extraction of herbs such as mint and processing local vegetables. In this paper, we discuss the financial and economic viability of the system and show how the energy, water and materials are completely recycled and how the benefits are directed to the weaker sections of the community.

Do intelligent heating controls out-smart ordinary users?

Nearly a third of UK gas and electricity is used in homes, of which 80% is for space heating and hot water provision. Rising consumer bills, concerns about climate change and the surge in personal digital technology use has provoked the development of intelligent domestic heating controls. Whilst the need for having suitable control of the home heating system is essential for reducing domestic energy use, these heating controls rely on appropriate user interaction to achieve a saving and it is unclear whether these ‘smart’ heating controls enhance the use of domestic heating or reduce energy demand. This paper describes qualitative research undertaken with a small sample of UK householders to understand how people use new heating controls installed in their homes and what the requirements are for improved smart heating control design. The paper identifies, against Nielsen’s usability heuristics, the divergence between the householder’s use, understanding and expectations of the heating system and the actual design of the system. Digital and smart heating control systems should be designed to maximise usability so that they can be effectively used for efficient heating control by all users. The research highlights the need for development of new systems to readdress the needs of users and redefine the system requirements.