Stand-alone groundwater desalination system using reverse osmosis combined with a cooled greenhouse for use in arid and semi-arid zones of India

In many areas of northern India, salinity renders groundwater unsuitable for drinking and even for irrigation. Though membrane treatment can be used to remove the salt, there are some drawbacks to this approach e.g. (1) depletion of the groundwater due to over-abstraction, (2) saline contamination of surface water and soil caused by concentrate disposal and (3) high electricity usage. To address these issues, a system is proposed in which a photovoltaic-powered reverse osmosis (RO) system is used to irrigate a greenhouse (GH) in a stand-alone arrangement. The concentrate from the RO is supplied to an evaporative cooling system, thus reducing the volume of the concentrate so that finally it can be evaporated in a pond to solid for safe disposal. Based on typical meteorological data for Delhi, calculations based on mass and energy balance are presented to assess the sizing and cost of the system. It is shown that solar radiation, freshwater output and evapotranspiration demand are readily matched due to the approximately linear relation among these variables. The demand for concentrate varies independently, however, thus favouring the use of a variable recovery arrangement. Though enough water may be harvested from the GH roof to provide year-round irrigation, this would require considerable storage. Some practical options for storage tanks are discussed. An alternative use of rainwater is in misting to reduce peak temperatures in the summer. An example optimised design provides internal temperatures below 30EC (monthly average daily maxima) for 8 months of the year and costs about €36,000 for the whole system with GH floor area of 1000 m2 . Further work is needed to assess technical risks relating to scale-deposition in the membrane and evaporative pads, and to develop a business model that will allow such a project to succeed in the Indian rural context.

A greenhouse integrating desalination, water saving and rainwater harvesting for use in salt-affected inland regions

This study proposes a new type of greenhouse for water re-use and energy saving for agriculture in arid and semi-arid inland regions affected by groundwater salinity. It combines desalination using reverse osmosis (RO), re-use of saline concentrate rejected by RO for cooling, and rainwater harvesting. Experimental work was carried at GBPUAT, Pantnagar, India. Saline concentrate was fed to evaporative cooling pads of greenhouse and found to evaporate at similar rates as conventional freshwater. Two enhancements to the system are described: i) A jet pump, designed and tested to use pressurized reject stream to re-circulate cooling water and thus maintain uniform wetness in cooling pads, was found capable of multiplying flow of cooling water by a factor of 2.5 to 4 while lifting water to a head of 1.55 m; and ii) Use of solar power to drive ventilation fans of greenhouse, for which an electronic circuit has been produced that uses maximum power-point tracking to maximize energy efficiency. Re-use of RO rejected concentrate for cooling saves water (6 l d-1 m-2) of greenhouse floor area and the improved fan could reduce electricity consumption by a factor 8.

Sustainable agricultural production:an investigation in Brazilian semi-arid livestock farms

This paper investigates the environmental sustainability and competitiveness perceptions of small farmers in a region in northern Brazil. The main data collection instruments included a survey questionnaire and an analysis of the region's strategic plan. In total, ninety-nine goat and sheep breeding farmers were surveyed. Data analysis methods included descriptive statistics, cluster analysis, and chi-squared tests. The main results relate to the impact of education, land size, and location on the farmers' perceptions of competitiveness and environmental issues. Farmers with longer periods of education have higher perception scores about business competitiveness and environmental sustainability than those with less formal education. Farmers who are working larger land areas also have higher scores than those with smaller farms. Lastly, location can yield factors that impact on farmers' perceptions. In our study, farmers located in Angicos and Lajes had higher perception scores than Pedro Avelino and Afonso Bezerra, despite the geographical proximity of these municipalities. On the other hand, three other profile variables did not impact on farmers' perceptions, namely: family income, dairy production volume, and associative condition. The authors believe the results and insights can be extended to livestock farming in other developing countries and contribute generally to fostering effective sustainable development policies, mainly in the agribusiness sector. © 2013 Elsevier Ltd. All rights reserved.

Novel hydrogel copolymers and semi-interpenetraing polymer networks

Interpenetrating polymer networks (lPN's), have been defined as a combination of two polymers each in network form, at least one of which has been synthesised and / or crosslinked in the presence of the other. A semi-lPN, is formed when only one of the polymers in the system is crosslinked, the other being linear. lPN's have potential advantages over homogeneous materials presently used in biomedical applications, in that their composite nature gives them a useful combination of properties. Such materials have potential uses in the biomedical field, specifically for use in hard tissue replacements, rigid gas permeable contact lenses and dental materials. Work on simply two or three component systems in both low water containing lPN's supplemented by the study of hydrogels (water swollen hydrophilic polymers) can provide information useful in the future development of more complex systems. A range of copolymers have been synthesised using a variety of methacrylates and acrylates. Hydrogels were obtained by the addition of N-vinyl pyrrolidone to these copolymers. A selection of interpenetrants were incorporated into the samples and their effect on the copolymer properties was investigated. By studying glass transition temperatures, mechanical, surface, water binding and oxygen permeability properties samples were assessed for their suitability for use as biomaterials. In addition copolymers containing tris-(trimethylsiloxy)-y-methacryloxypropyl silane, commonly abbreviated to 'TRlS', have been investigated. This material has been shown to enhance oxygen permeability, a desirable property when considering the design of contact lenses. However, 'TRIS' has a low polar component of surface free energy and hence low wettability. Copolymerisation with a range of methacrylates has shown that significant increases in surface wettability can be obtained without a detrimental effect on oxygen permeability. To further enhance to surface wettability 4-methacryloxyethyl trimellitic anhydride was incorporated into a range of promising samples. This study has shown that by careful choice of monomers it is possible to synthesise polymers that possess a range of properties desirable in biomedical applications.

Improving the solubility and dissolution of poorly soluble drugs by salt formation and the consequent effect on mechanical properties

The bioavailability of BCS II compounds may be improved by an enhanced solubility and dissolution rate. Four carboxylic acid drugs were selected, which were flurbiprofen, etodolac, ibuprofen and gemfibrozil. The drugs were chosen because they are weak acids with poor aqueous solubility and should readily form salts. The counterions used for salt formation were: butylamine, pentylamine, hexylamine, octylamine, benzylamine, cyclohexylamine, tert-butylamine, 2-amino-2-methylpropan­2-ol, 2-amino-2-methyl propan-1,3-ol and tromethamine. Solubility was partially controlled by the saturated solution pH with the butylamine counterion increasing the solution pH and solubility and dissolution to the greatest extent. As the chain length increased, solubility was reduced due to the increasing lipophilic nature of the counterion. The benzylamine and cyclohexylamine counterions produced crystalline, stable salts but did not improve solubility and dissolution significantly compared to the parent compound. The substitution of hydroxyl groups to tert-butylamine counterions produced an increase in solubility and dissolution. AMP2 resulted in the most enhanced solubility and dissolution compared to the parent drug but using the tris salt did not further improve solubility due to a very stable crystal lattice structure. The parent drugs were very difficult to compress due to orientation effects and lamination. Compacts were prepared of each parent drug and salt and their modulus of elasticity values were measured using a three-point bend (Young’s modulus, E0) were extrapolated to zero porosity and compared. Compressibility and E0 were improved with the butylamine, tert-butylamine, cyclohexylamine and AMP2 counterions. The most significant improvement in compression and E0 was with the AMP2 salts. Mechanical properties were related to the hydrogen bonding within the crystal lattice structure for the gemfibrozil salt series.

Lithological mapping of Northwest Argentina with remote sensing data using tonal, textural and contextual features

Tonal, textural and contextual properties are used in manual photointerpretation of remotely sensed data. This study has used these three attributes to produce a lithological map of semi arid northwest Argentina by semi automatic computer classification procedures of remotely sensed data. Three different types of satellite data were investigated, these were LANDSAT MSS, TM and SIR-A imagery. Supervised classification procedures using tonal features only produced poor classification results. LANDSAT MSS produced classification accuracies in the range of 40 to 60%, while accuracies of 50 to 70% were achieved using LANDSAT TM data. The addition of SIR-A data produced increases in the classification accuracy. The increased classification accuracy of TM over the MSS is because of the better discrimination of geological materials afforded by the middle infra red bands of the TM sensor. The maximum likelihood classifier consistently produced classification accuracies 10 to 15% higher than either the minimum distance to means or decision tree classifier, this improved accuracy was obtained at the cost of greatly increased processing time. A new type of classifier the spectral shape classifier, which is computationally as fast as a minimum distance to means classifier is described. However, the results for this classifier were disappointing, being lower in most cases than the minimum distance or decision tree procedures. The classification results using only tonal features were felt to be unacceptably poor, therefore textural attributes were investigated. Texture is an important attribute used by photogeologists to discriminate lithology. In the case of TM data, texture measures were found to increase the classification accuracy by up to 15%. However, in the case of the LANDSAT MSS data the use of texture measures did not provide any significant increase in the accuracy of classification. For TM data, it was found that second order texture, especially the SGLDM based measures, produced highest classification accuracy. Contextual post processing was found to increase classification accuracy and improve the visual appearance of classified output by removing isolated misclassified pixels which tend to clutter classified images. Simple contextual features, such as mode filters were found to out perform more complex features such as gravitational filter or minimal area replacement methods. Generally the larger the size of the filter, the greater the increase in the accuracy. Production rules were used to build a knowledge based system which used tonal and textural features to identify sedimentary lithologies in each of the two test sites. The knowledge based system was able to identify six out of ten lithologies correctly.

A solar powered liquid-desiccant cooling system for greenhouses

Liquid desiccant systems are of potential interest as a means of cooling greenhouses to temperatures below those achieved by conventional means. However, only very little work has been done on this technology with previous workers focussing on the cooling of human dwellings using expensive desiccants such as lithium salts. In this study we are designing a system for greenhouse cooling based on magnesium chloride desiccant which is an abundant and non-toxic substance. Magnesium chloride is found in seawater, for example, and is a by-product from solar salt works. We have carried out a detailed experimental study of the relevant properties of magnesium rich solutions. In addition we have constructed a test rig that includes the main components of the cooling system, namely a dehumidifier and solar regenerator. The dehumidifier is a cross-flow device that consists of a structured packing made of corrugated cellulose paper sheets with different flute angles and embedded cooling tubes. The regenerator is of the open type with insulated backing and fabric covering to spread the flow of desiccant solution. Alongside these experiments we are developing a mathematical model in gPROMS® that combines and simulates the heat and mass transfer processes in these components. The model can be applied to various geographical locations. Here we report predictions for Havana (Cuba) and Manila (Philippines), where we find that average wet-bulb temperatures can be lowered by 2.2 and 3°C, respectively, during the month of May.

Energy saving and solar electricity in fan-ventilated greenhouses

Greenhouse cultivation is an energy intensive process therefore it is worthwhile to introduce energy saving measures and alternative energy sources. Here we show that there is scope for energy saving in fan ventilated greenhouses. Measurements of electricity usage as a function of fan speed have been performed for two models of 1.25 m diameter greenhouse fans and compared to theoretical values. Reducing the speed can cut the energy usage per volume of air moved by more than 70%. To minimize the capital cost of low-speed operation, a cooled greenhouse has been built in which the fan speed responds to sunlight such that full speed is reached only around noon. The energy saving is about 40% compared to constant speed operation. Direct operation of fans from solar-photovoltaic modules is also viable as shown from experiments with a fan driven by a brushless DC motor. On comparing the Net Present Value costs of the different systems over a 10 year amortization period (with and without a carbon tax to represent environmental costs) we find that sunlight-controlled system saves money under all assumptions about taxation and discount rates. The solar-powered system, however, is only profitable for very low discount rates, due to the high initial capital costs. Nonetheless this system could be of interest for its reliability in developing countries where mains electricity is intermittent. We recommend that greenhouse fan manufacturers improve the availability of energy-saving designs such as those described here.

The structure and dynamics of saxicolous lichen communities

The saxicolous lichen vegetation on Ordovician slate rock at the mouth of the River Dovey, South Merionethshire, Wales was described in relation to several environmental variables which include aspect, slope angle, light intensity, rock porosity, rock microtopography and rock stability. Each of the measured environmental variables was shown to influence the lichen vegetation. A number of groups of species which were characteristic of certain environments were described. The data from the saxicolous lichen communities were analysed using multivariate analysis. Qualitative and quantitative data were ordinated, the qualitative data being easier to interpret ecologically, and site number (which reflects distance from the sea and altitude), rock porosity and light intensity were shown to be important environmental variables. A classification of the data was also carried out. The results of the ordination and classification were combined together and a model constructed which describes saxicolous lichen vegetation. A method which uses the model as an aid to the design and interpretation of field experiments is described. The model is applied to an experiment which investigates the effect on growth of transplanting four saxicolous lichens to different aspects. Growth was inhibited in Physcia orbicularis and Parmelia conspersa on rock surfaces of northwest aspect compared with growth on rock surfaces of southeast aspect. Growth was inhibited in Parmelia glabratula ssp. fuliginosa on rock surfaces of southeast aspect compared with rock surfaces of northwesr aspect. The growth of Parmelia saxatilis was similar at both southeast and northwesr aspects. Growth inhibition or stimulation in thalli of Physcia orbicularis, Parmelia conspersa and Parmelia glabratula ssp. fuliginosa after transplantation was consistent with the predictions of the model while the results for Parmelia saxatilis were not as expected. There was evidence that the frequency of Parmelia conspersa and Parmelia glabratula at a site is related to an effect of the environment on the growth of the thalli. There was also evidence that the frequency of Physcia orbicularis at a site is related to an effect of the environment on the establishment phase of the thalli and for the competitive exclusion of Parmelia saxatilis thalli from southeast facing rock surfaces. The distribution of lichens in relation to height on nine rock surfaces was investigated. It was suggested that the distribution of the lichens was influenced by microclimatic factors which are related to height on the rock, environmental variables which are associated with the rock substratum (e.g. rock porosity and rock microtopography) and by historical factors. The pattern of one crustose and one foliose lichen on four rock surfaces of different aspect and slope was investigated. On the vertically inclined surface the density of small thalli of Buellia aethalea and Parmelia glabratula ssp fuliginosa was correlated with the microtopography of the surface in transects horizontally across the rock surface but not in transects vertically down the rock surface. there were consitent differences in the scale and intensity of pattern horizontally and vertically and also a decrease in the intensity of pattern vertically as the slope of the rock surface decreased. These results were consistent with the suggestion of a gradient of microclimatic factors up the rock. The differences in the scale and intensity of pattern in different size classes in the population were consistent with the changes in pattern with time which have been shown to occur during succession in sand dune and salt marsh vegetation. The relationship between thallus size and height on a rock surface and between the radial growth rate and location of a thallus on a rock surface were investigated. Thalli of Parmelia glabratula ssp. fuliginosa were larger at the top of the rock surface than at the bottom and the data were consistent with the suggestion that the colonisation of the rock surface began at the top and, in time, spread downwards. The radial growth rate of the thalli could not be related to variation in slope, porosity, microtopography or directly to height on the rock but could be related to the horizontal location of the thalli on the rock. These results were consistent with the suggestion that here is a gradient of microclimatic factors across the rock surface which is also modified by height on the rock surface. The succession of lichen communities was described by relating the vegetation to rock porosity, rock microtopography, species diversity and rock stability. An initial stage dominated by crustose lichens leads to communities dominated by crustose, foliose and fruticose species. In the late stages of the succession on some rock surfaces crustose species again become dominant. The occurrence of the climax state and cyclic vegetation change in lichen communities are discussed. A mthod of estimating the age structure of a lichen population by relating thallus size to growth rate is described. The sources of error in the method are discussed in some detail and several refinements suggested to increase the accuracy of the method. The population dynamics of Parmelia glabratula ssp. fuliginosa was investigated by applying life tables to the age structures of eight different populations. The data were consistent with a period of relatively constant recruitment of thalli into the populations. Mortality in lichen populations was divided into deaths which occur after fragmentation of the thallus and deaths which occur after catastrophic environmental events. THe data suggest that the rate of fragmenting death is dependent on the age of the thallus while the rate of catastrophic death is dependent on the number of thalli established in an age class. A comparison of the numbers of thalli in each age class in the eight populations suggested that population density is controlled firstly, by climate and secondly, by variables related to the local rock surface environment. The rate of fragmenting death is related to the diversity of the community and the influence of diversity together with environmental variables in fluctuating or cyclic changes in population number.

A micro industry with closed energy and water cycles for sustainable rural development

Sustainable development requires combining economic viability with energy and environment conservation and ensuring social benefits. It is conceptualized that for designing a micro industry for sustainable rural industrialization, all these aspects should be integrated right up front. The concept includes; (a) utilization of local produce for value addition in a cluster of villages and enhancing income of the target population; (b) use of renewable energy and total utilization of energy generated by co and trigeneration (combining electric power production with heat utilization for heating and cooling); (c) conservation of water and complete recycling of effluents; (d) total utilization of all wastes for achieving closure towards a zero waste system. Enhanced economic viability and sustainability is achieved by integration of appropriate technologies into the industrial complex. To prove the concept, a model Micro Industrial Complex (MIC) has been set up in a semi arid desert region in Rajasthan, India at village Malunga in Jodhpur district. A biomass powered boiler and steam turbine system is used to generate 100-200 KVA of electric power and high energy steam for heating and cooling processes downstream. The unique feature of the equipment is a 100-150 kW back-pressure steam turbine, utilizing 3-4 tph (tonnes per hour) steam, developed by M/s IB Turbo. The biomass boiler raises steam at about 20 barg 3 tph, which is passed through a turbine to yield about 150 kW of electrical power. The steam let out at a back pressure of 1-3 barg has high exergy and this is passed on as thermal energy (about 2 MW), for use in various applications depending on the local produce and resources. The biomass fuel requirement for the boiler is 0.5-0.75 tph depending on its calorific value. In the current model, the electricity produced is used for running an oil expeller to extract castor oil and the castor cake is used as fuel in the boiler. The steam is used in a Multi Effect Distillation (MED) unit for drinking water production and in a Vapour Absorption Machine (VAM) for cooling, for banana ripening application. Additional steam is available for extraction of herbs such as mint and processing local vegetables. In this paper, we discuss the financial and economic viability of the system and show how the energy, water and materials are completely recycled and how the benefits are directed to the weaker sections of the community.