Study on the pyrolytic behaviour of xylan-based hemicellulose using TG-FTIR and Py-GC-FTIR

Two sets of experiments, categorized as TG–FTIR and Py–GC–FTIR, are employed to investigate the mechanism of the hemicellulose pyrolysis and the formation of main gaseous and bio-oil products. The “sharp mass loss stage” and the corresponding evolution of the volatile products are examined by the TG–FTIR graphs at the heating rate of 3–80 K/min. A pyrolysis unit, composed of fluidized bed reactor, carbon filter, vapour condensing system and gas storage, is employed to investigate the products of the hemicellulose pyrolysis under different temperatures (400–690 °C) at the feeding flow rate of 600 l/h. The effects of temperature on the condensable products are examined thoroughly. The possible routes for the formation of the products are systematically proposed from the primary decomposition of the three types of unit (xylan, O-acetylxylan and 4-O-methylglucuronic acid) and the secondary reactions of the fragments. It is found that the formation of CO is enhanced with elevated temperature, while slight change is observed for the yield of CO2 which is the predominant products in the gaseous mixture.

Analytic hierarchy process helps evaluate projects in Indian oil pipeline industry

Conventionally, oil pipeline projects are evaluated thoroughly by the owner before investment decision is made using market, technical and financial analysis sequentially. The market analysis determines pipelines throughput and supply and demand points. Subsequent, technical analysis identifies technological options and economic and financial analysis then derives the least cost option among all technically feasible options. The subsequent impact assessment tries to justify the selected option by addressing environmental and social issues. The impact assessment often suggests alternative sites, technologies, and/or implementation methodology, necessitating revision of technical and financial analysis. This study addresses these issues via an integrated project evaluation and selection model. The model uses analytic hierarchy process, a multiple-attribute decision-making technique. The effectiveness of the model has been demonstrated through a case application on cross-country petroleum pipeline project in India.

Multiple attribute decision making approach to petroleum pipeline route selection

Petroleum pipelines are the nervous system of the oil industry, as this transports crude oil from sources to refineries and petroleum products from refineries to demand points. Therefore, the efficient operation of these pipelines determines the effectiveness of the entire business. Pipeline route selection plays a major role when designing an effective pipeline system, as the health of the pipeline depends on its terrain. The present practice of route selection for petroleum pipelines is governed by factors such as the shortest distance, constructability, minimal effects on the environment, and approachability. Although this reduces capital expenditure, it often proves to be uneconomical when life cycle costing is considered. This study presents a route selection model with the application of an Analytic Hierarchy Process (AHP), a multiple attribute decision making technique. AHP considers all the above factors along with the operability and maintainability factors interactively. This system has been demonstrated here through a case study of pipeline route selection, from an Indian perspective. A cost-benefit comparison of the shortest route (conventionally selected) and optimal route establishes the effectiveness of the model.

Managing technology in oil pipelines industry

Operating oil pipelines in an optimum capacity through out its life, effective construction management and failure free operations are considered as critical success factors in oil transportation business. Operating oil pipelines in derated capacity due to deteriorating pipeline health or lack of demand, non-ability of augmenting pipeline capacity despite of demand, non-achievement of time, cost, and quality of pipeline construction projects, and many failures of pipelines despite of huge expenditure in inspection and maintenance are the common phenomena in oil pipelines industry. These not only cause business loss, but also increase stakeholders' concerns for sustainable development. This study addresses the above issues using an analytical framework through stakeholders' involvement. Copyright © 2006 Inderscience Enterprises Ltd.

Effect of a fish oil-enriched nutritional supplement on metabolic mediators in patients with pancreatic cancer cachexia

Weight loss in advanced cancer patients is refractory to conventional nutritional support. This may be due to metabolic changes mediated by proinflammatory cytokines, hormones, and tumor-derived products. We previously showed that a nutritional supplement enriched with fish oil will reverse weight loss in patients with pancreatic cancer cachexia. The present study examines the effect of this supplement on a number of mediators thought to play a role in cancer cachexia. Twenty weight-losing patients with pancreatic cancer were asked to consume a nutritional supplement providing 600 kcal and 2 g of eicosapentaenoic acid per day. At baseline and after 3 wk, patients were weighed and samples were collected to measure serum concentrations of interleukin (IL)-6 and its soluble receptor tumor necrosis factor receptors I and II, cortisol, insulin, and leptin, peripheral blood mononuclear cell production of IL-1 beta, IL-6, and tumor necrosis factor, and urinary excretion of proteolysis inducing factor. After 3 wk of consumption of the fish oil-enriched nutritional supplement, there was a significant fall in production of IL-6 (from median 16.5 to 13.7 ng/ml, P = 0.015), a rise in serum insulin concentration (from 3.3 to 5.0 mU/l, P = 0.0064), a fall in the cortisol-to-insulin ratio (P = 0.0084), and a fall in the proportion of patients excreting proteolysis inducing factor (from 88% to 40%, P = 0.008). These changes occurred in association with weight gain (median 1 kg, P = 0.024). Various mediators of catabolism in cachexia are modulated by administration of a fish oil-enriched nutritional supplement in pancreatic cancer patients. This may account for the reversal of weight loss in patients consuming this supplement.

Introduction: improving manufacturing performance through technology diffusion, implementation and management

The role of technology management in achieving improved manufacturing performance has been receiving increased attention as enterprises are becoming more exposed to competition from around the world. In the modern market for manufactured goods the demand is now for more product variety, better quality, shorter delivery and greater flexibility, while the financial and environmental cost of resources has become an urgent concern to manufacturing managers. This issue of the International Journal of Technology Management addresses the question of how the diffusion, implementation and management of technology can improve the performance of manufacturing industries. The authors come from a large number of different countries and their contributions cover a wide range of topics within this general theme. Some papers are conceptual, others report on research carried out in a range of different industries including steel production, iron founding, electronics, robotics, machinery, precision engineering, metal working and motor manufacture. In some cases they describe situations in specific countries. Several are based on presentations made at the UK Operations Management Association's Sixth International Conference held at Aston University at which the conference theme was 'Achieving Competitive Edge: Getting Ahead Through Technology and People'. The first two papers deal with questions of advanced manufacturing technology implementation and management. Firstly Beatty describes a three year longitudinal field study carried out in ten Canadian manufacturing companies using CADICAM and CIM systems. Her findings relate to speed of implementation, choice of system type, the role of individuals in implementation, organization and job design. This is followed by a paper by Bessant in which he argues that a more a strategic approach should be taken towards the management of technology in the 1990s and beyond. Also considered in this paper are the capabilities necessary in order to deploy advanced manufacturing technology as a strategic resource and the way such capabilities might be developed within the firm. These two papers, which deal largely with the implementation of hardware, are supplemented by Samson and Sohal's contribution in which they argue that a much wider perspective should be adopted based on a new approach to manufacturing strategy formulation. Technology transfer is the topic of the following two papers. Pohlen again takes the case of advanced manufacturing technology and reports on his research which considers the factors contributing to successful realisation of AMT transfer. The paper by Lee then provides a more detailed account of technology transfer in the foundry industry. Using a case study based on a firm which has implemented a number of transferred innovations a model is illustrated in which the 'performance gap' can be identified and closed. The diffusion of technology is addressed in the next two papers. In the first of these, by Lowe and Sim, the managerial technologies of 'Just in Time' and 'Manufacturing Resource Planning' (or MRP 11) are examined. A study is described from which a number of factors are found to influence the adoption process including, rate of diffusion and size. Dahlin then considers the case of a specific item of hardware technology, the industrial robot. Her paper reviews the history of robot diffusion since the early 1960s and then tries to predict how the industry will develop in the future. The following two papers deal with the future of manufacturing in a more general sense. The future implementation of advanced manufacturing technology is the subject explored by de Haan and Peters who describe the results of their Dutch Delphi forecasting study conducted among a panel of experts including scientists, consultants, users and suppliers of AMT. Busby and Fan then consider a type of organisational model, 'the extended manufacturing enterprise', which would represent a distinct alternative pure market-led and command structures by exploiting the shared knowledge of suppliers and customers. The three country-based papers consider some strategic issues relating manufacturing technology. In a paper based on investigations conducted in China He, Liff and Steward report their findings from strategy analyses carried out in the steel and watch industries with a view to assessing technology needs and organizational change requirements. This is followed by Tang and Nam's paper which examines the case of machinery industry in Korea and its emerging importance as a key sector in the Korean economy. In his paper which focuses on Venezuela, Ernst then considers the particular problem of how this country can address the problem of falling oil revenues. He sees manufacturing as being an important contributor to Venezuela's future economy and proposes a means whereby government and private enterprise can co-operate in development of the manufacturing sector. The last six papers all deal with specific topics relating to the management manufacturing. Firstly Youssef looks at the question of manufacturing flexibility, introducing and testing a conceptual model that relates computer based technologies flexibility. Dangerfield's paper which follows is based on research conducted in the steel industry. He considers the question of scale and proposes a modelling approach determining the plant configuration necessary to meet market demand. Engstrom presents the results of a detailed investigation into the need for reorganising material flow where group assembly of products has been adopted. Sherwood, Guerrier and Dale then report the findings of a study into the effectiveness of Quality Circle implementation. Stillwagon and Burns, consider how manufacturing competitiveness can be improved individual firms by describing how the application of 'human performance engineering' can be used to motivate individual performance as well as to integrate organizational goals. Finally Sohal, Lewis and Samson describe, using a case study example, how just-in-time control can be applied within the context of computer numerically controlled flexible machining lines. The papers in this issue of the International Journal of Technology Management cover a wide range of topics relating to the general question of improving manufacturing performance through the dissemination, implementation and management of technology. Although they differ markedly in content and approach, they have the collective aim addressing the concepts, principles and practices which provide a better understanding the technology of manufacturing and assist in achieving and maintaining a competitive edge.

The effect of blending on selected physical properties of crude oils and their products

A study was made of the effect of blending practice upon selected physical properties of crude oils, and of various base oils and petroleum products, using a range of binary mixtures. The crudes comprised light, medium and heavy Kuwait crude oils. The properties included kinematic viscosity, pour point, boiling point and Reid vapour pressure. The literature related to the prediction of these properties, and the changes reported to occur on blending, was critically reviewed as a preliminary to the study. The kinematic viscosity of petroleum oils in general exhibited non-ideal behaviour upon blending. A mechanism was proposed for this behaviour which took into account the effect of asphaltenes content. A correlation was developed, as a modification of Grunberg's equation, to predict the viscosities of binary mixtures of petroleum oils. A correlation was also developed to predict the viscosities of ternary mixtures. This correlation showed better agreement with experimental data (< 6% deviation for crude oils and 2.0% for base oils) than currently-used methods, i.e. ASTM and Refutas methods. An investigation was made of the effect of temperature on the viscosities of crude oils and petroleum products at atmospheric pressure. The effect of pressure on the viscosity of crude oil was also studied. A correlation was developed to predict the viscosity at high pressures (up to 8000 psi), which gave significantly better agreement with the experimental data than the current method due to Kouzel (5.2% and 6.0% deviation for the binary and ternary mixtures respectively). Eyring's theory of viscous flow was critically investigated, and a modification was proposed which extends its application to petroleum oils. The effect of blending on the pour points of selected petroleum oils was studied together with the effect of wax formation and asphaltenes content. Depression of the pour point was always obtained with crude oil binary mixtures. A mechanism was proposed to explain the pour point behaviour of the different binary mixtures. The effects of blending on the boiling point ranges and Reid vapour pressures of binary mixtures of petroleum oils were investigated. The boiling point range exhibited ideal behaviour but the R.V.P. showed negative deviations from it in all cases. Molecular weights of these mixtures were ideal, but the densities and molar volumes were not. The stability of the various crude oil binary mixtures, in terms of viscosity, was studied over a temperature range of 1oC - 30oC for up to 12 weeks. Good stability was found in most cases.

The analysis of organic matter in oil-shales

The organic matter in five oil shales (three from the Kimmeridge Clay sequence, one from the Oxford Clay sequence and one from the Julia Creek deposits in Australia) has been isolated by acid demineralisation, separated into kerogens and bitumens by solvent extraction and then characterised in some detail by chromatographic, spectroscopic and degradative techniques. Kerogens cannot be characterised as easily as bitumens because of their insolubility, and hence before any detailed molecular information can be obtained from them they must be degraded into lower molecular weight, more soluble components. Unfortunately, the determination of kerogen structures has all too often involved degradations that were far too harsh and which lead to destruction of much of the structural information. For this reason a number of milder more selective degradative procedures have been tested and used to probe the structure of kerogens. These are: 1. Lithium aluminium hydride reduction. - This procedure is commonly used to remove pyrite from kerogens and it may also increase their solubility by reduction of labile functional groups. Although reduction of the kerogens was confirmed, increases in solubility were correlated with pyrite content and not kerogen reduction. 2. O-methylation in the presence of a phase transfer catalyst. - By the removal of hydrogen bond interactions via O-methylation, it was possible to determine the contribution of such secondary interactions to the insolubility of the kerogens. Problems were encountered with the use of the phase transfer catalyst. 3. Stepwise alkaline potassium permanganate oxidation. - Significant kerogen dissolution was achieved using this procedure but uncontrolled oxidation of initial oxidation products proved to be a problem. A comparison with the peroxytrifluoroaceticacid oxidation of these kerogens was made. 4. Peroxytrifluoroacetic acid oxidation. - This was used because it preferentially degrades aromatic rings whilst leaving any benzylic positions intact. Considerable conversion of the kerogens into soluble products was achieved with this procedure. At all stages of degradation the products were fully characterised where possible using a variety of techniques including elemental analysis, solution state 1H and 13C nuclear magnetic resonance, solid state 13C nuclear magnetic resonance, gel-permeationchromatography, gas chromatography-mass spectroscopy, fourier transform infra-red spectroscopy and some ultra violet-visible spectroscopy.

Prediction of Klason lignin and lignin thermal degradation products by Py-GC/MS in a collection of Lolium and Festuca grasses

A rapid method for the analysis of biomass feedstocks was established to identify the quality of the pyrolysis products likely to impact on bio-oil production. A total of 15 Lolium and Festuca grasses known to exhibit a range of Klason lignin contents were analysed by pyroprobe-GC/MS (Py-GC/MS) to determine the composition of the thermal degradation products of lignin. The identification of key marker compounds which are the derivatives of the three major lignin subunits (G, H, and S) allowed pyroprobe-GC/MS to be statistically correlated to the Klason lignin content of the biomass using the partial least-square method to produce a calibration model. Data from this multivariate modelling procedure was then applied to identify likely "key marker" ions representative of the lignin subunits from the mass spectral data. The combined total abundance of the identified key markers for the lignin subunits exhibited a linear relationship with the Klason lignin content. In addition the effect of alkali metal concentration on optimum pyrolysis characteristics was also examined. Washing of the grass samples removed approximately 70% of the metals and changed the characteristics of the thermal degradation process and products. Overall the data indicate that both the organic and inorganic specification of the biofuel impacts on the pyrolysis process and that pyroprobe-GC/MS is a suitable analytical technique to asses lignin composition. © 2007 Elsevier B.V. All rights reserved.

Design of a stock control methodology for use within an oil blending company

The thesis deals with the background, development and description of a mathematical stock control methodology for use within an oil and chemical blending company, where demand and replenishment lead-times are generally non-stationary. The stock control model proper relies on, as input, adaptive forecasts of demand determined for an economical forecast/replenishment period precalculated on an individual stock-item basis. The control procedure is principally that of the continuous review, reorder level type, where the reorder level and reorder quantity 'float', that is, each changes in accordance with changes in demand. Two versions of the Methodology are presented; a cost minimisation version and a service level version. Realising the importance of demand forecasts, four recognised variations of the Trigg and Leach adaptive forecasting routine are examined. A fifth variation, developed, is proposed as part of the stock control methodology. The results of testing the cost minimisation version of the Methodology with historical data, by means of a computerised simulation, are presented together with a description of the simulation used. The performance of the Methodology is in addition compared favourably to a rule-of-thumb approach considered by the Company as an interim solution for reducing stack levels. The contribution of the work to the field of scientific stock control is felt to be significant for the following reasons:- (I) The Methodology is designed specifically for use with non-stationary demand and for this reason alone appears to be unique. (2) The Methodology is unique in its approach and the cost-minimisation version is shown to work successfully with the demand data presented. (3) The Methodology and the thesis as a whole fill an important gap between complex mathematical stock control theory and practical application. A brief description of a computerised order processing/stock monitoring system, designed and implemented as a pre-requisite for the Methodology's practical operation, is presented as an appendix.

The effects of the changing energy situation on demand for industrial heat exchangers

The Project arose during a period in which the World was still coming to terms with the effects and implications of the so called 'energy crisis' of 1973/74. Serck Heat Transfer is a manufacturer of heat exchangers which transfer heat between fluids of various sorts. As such the company felt that past and possible future changes in the energy situation could have an impact upon the demand for its products. The thesis represents the first attempt to examine the impact of changes in the energy situation (a major economic variable) on the long term demand for heat exchangers. The scope of the work was limited to the United Kingdom, this being the largest single market for Serek's products. The thesis analyses industrial heat exchanger markets and identifies those trends which are related to both the changing energy situation and the usage of heat exchangers. These trends have been interpreted In terms of projected values of heat exchanger demand. The projections cover the period 197S to the year 2000. Also examined in the thesis is the future energy situation both internationally and nationally and it is found that in the long term there will be increasing pressure on consumers to conserve energy through rising real prices. The possibility of a connection between energy consumption and heat exchanger demand is investigated and no significant correlation found. This appears to be because there are a number of determinants of demand besides energy related factors and also there is a wide diversity of individual markets for heat exchangers. Conclusions are that in all markets, bar one, the changing energy situation should lead to a higher level of heat exchanger demand than would otherwise be the case had the energy situation not changed. It is also pointed out that it is misleading to look at changes in one influence on the demand for a product and ignore others.

The characterisation and optimisation of modified herbaceous grasses for identifying pyrolisis-oil quality traits

The primary objective of this work is to relate the biomass fuel quality to fast pyrolysis-oil quality in order to identify key biomass traits which affect pyrolysis-oil stability. During storage the pyrolysis-oil becomes more viscous due to chemical and physical changes, as reactions and volatile losses occur due to aging. The reason for oil instability begins within the pyrolysis reactor during pyrolysis in which the biomass is rapidly heated in the absence of oxygen, producing free radical volatiles which are then quickly condensed to form the oil. The products formed do not reach thermodynamic equilibrium and in tum the products react with each other to try to achieve product stability. The first aim of this research was to develop and validate a rapid screening method for determining biomass lignin content in comparison to traditional, time consuming and hence costly wet chemical methods such as Klason. Lolium and Festuca grasses were selected to validate the screening method, as these grass genotypes exhibit a low range of Klason /Acid Digestible Fibre lignin contents. The screening methodology was based on the relationship between the lignin derived products from pyrolysis and the lignin content as determined by wet chemistry. The second aim of the research was to determine whether metals have an affect on fast pyrolysis products, and if any clear relationships can be deduced to aid research in feedstock selection for fast pyrolysis processing. It was found that alkali metals, particularly Na and K influence the rate and yield of degradation as well the char content. Pre-washing biomass with water can remove 70% of the total metals, and improve the pyrolysis product characteristics by increasing the organic yield, the temperature in which maximum liquid yield occurs and the proportion of higher molecular weight compounds within the pyrolysis-oil. The third aim identified these feedstock traits and relates them to the pyrolysis-oil quality and stability. It was found that the mineral matter was a key determinant on pyrolysis-oil yield compared to the proportion of lignin. However the higher molecular weight compounds present in the pyrolysis-oil are due to the lignin, and can cause instability within the pyrolysis-oil. The final aim was to investigate if energy crops can be enhanced by agronomical practices to produce a biomass quality which is attractive to the biomass conversion community, as well as giving a good yield to the farmers. It was found that the nitrogen/potassium chloride fertiliser treatments enhances Miscanthus qualities, by producing low ash, high volatiles yields with acceptable yields for farmers. The progress of senescence was measured in terms of biomass characteristics and fast pyrolysis product characteristics. The results obtained from this research are in strong agreement with published literature, and provides new information on quality traits for biomass which affects pyrolysis and pyrolysis-oils.

Effect of contact surfaces on the thermal and photoxidation of dehydrated castor oil

The effect of stainless steel, glass, zirconium and titanium enamel surfaces on the thermal and photooxidative toughening mechanism of dehydrated castor oil films deposited on these surfaces was investigated using different analytical and spectroscopic methods. The conjugated and non-conjugated double bonds were identified and quantified using both Raman spectroscopy and 1D and 2D NMR spectroscopy. The disappearance of the double bonds in thermally oxidised oil-on-surface films was shown to be concomitant with the formation of hydroperoxides (determined by iodometric titration). The type of the surface had a major effect on the rate of thermal oxidation of the oil, but all of the surfaces examined had resulted in a significantly higher rate of oxidation compared to that of the neat oil. The highest effect was exhibited by the stainless steel surface followed by zirconium enamel, titanium enamel and glass. The rate of thermal oxidation of the oil-on-steel surface (at 100 °C, based on peroxide values) was more than five times faster than that of oil-on-glass and more than 21 times faster than the neat oil when compared under similar thermal oxidative conditions. The rate of photooxidation at 60 °C of oil-on-steel films was found to be about one and half times faster than their rate of thermal oxidation at the same temperature. Results from absorbance reflectance infrared microscopy with line scans taken across the depth of thermally oxidised oil-on-steel films suggest that the thermal oxidative toughening mechanism of the oil occurs by two different reaction pathways with the film outermost layers, i.e. furthest away from the steel surface, oxidising through a traditional free radical oxidation process involving the formation of various oxygenated products formed from the decomposition of allylic hydroperoxides, whereas, in the deeper layers closer to the steel surface, crosslinking reactions predominate.

Developing and evaluating a methodology for business process improvement

Purpose – There appears to be an ever-insatiable demand from markets for organisations to improve their products and services. To meet this, there is a need to provide business process improvement (BPI) methodologies that are holistic, structured and procedural. Therefore, this paper describes research that has formed and tested a generic and practical methodology termed model-based and integrated process improvement (MIPI) to support the implementation of BPI; and to validate its effectiveness in organisations. This methodology has been created as an aid for practitioners within organisations. Design/methodology/approach – The research objectives were achieved by: reviewing and analysing current methodologies, and selecting a few frameworks against key performance indicators. Using a refined Delphi approach and semi-structured interview with the “experts” in the field. Intervention, case study and process research approach to evaluating a methodology. Findings – The BPI methodology was successfully formed and applied by the researcher and directly by the companies involved against the criteria of feasibility, usability and usefulness. Research limitations/implications – The paper has demonstrated a new knowledge on how to systematically assess a BPI methodology in practice. Practical implications – Model-based and integrated process improvement methodology (MIPI) methodology offers the practitioner (experienced and novice) a set of step-by-step aids necessary to make informed, consistent and efficient changes to business processes. Originality/value – The novelty of this research work is the creation of a holistic workbook-based methodology with relevant tools and techniques. It extends the capabilities of existing methodologies.

Personal selling of high-technology products:the solutions-selling imperative

Traditional focus on the study of high-technology firms and products has practically ignored the importance and potential contributions of the sales force, especially in business-to-business marketing. This article suggests that traditional sales force strategies associated with high-technology products have been supply driven (i.e., driven by the strategies of the marketing firm). We suggest that in order to enhance the success of high-technology products and services, firms need to be more demand driven in their sales structures (i.e., driven by the strategies of the buying firm). We suggest that it is imperative that high-technology firms adopt “solution selling” to enhance high-technology adoption as well as enhance competitiveness. We describe this change in focus and draw out its various managerial and academic implications.