Pole tip recession in linear tape systems

The tribology of linear tape storage system including Linear Tape Open (LTO) and Travan5 was investigated by combining X-ray Photoelectron Spectroscopy (XPS), Auger Electron Spectroscopy (AES), Optical Microscopy and Atomic Force Microscopy (AFM) technologies. The purpose of this study was to understand the tribology mechanism of linear tape systems then projected recording densities may be achieved in future systems. Water vapour pressure or Normalized Water Content (NWC) rather than the Relative Humidity (RH) values (as are used almost universally in this field) determined the extent of PTR and stain (if produced) in linear heads. Approximately linear dependencies were found for saturated PTR increasing with normalized water content increasing over the range studied using the same tape. Fe Stain (if produced) preferentially formed on the head surfaces at the lower water contents. The stain formation mechanism had been identified. Adhesive bond formation is a chemical process that is governed by temperature. Thus the higher the contact pressure, the higher the contact temperature in the interface of head and tape, was produced higher the probability of adhesive bond formation and the greater the amount of transferred material (stain). Water molecules at the interface saturate the surface bonds and makes adhesive junctions less likely. Tape polymeric binder formulation also has a significant role in stain formation, with the latest generation binders producing less transfer of material. This is almost certainly due to higher cohesive bonds within the body of the magnetic layer. TiC in the two-phase ceramic tape-bearing surface (AlTiC) was found to oxidise to form TiO2.The oxidation rate of TiC increased with water content increasing. The oxide was less dense than the underlying carbide; hence the interface between TiO2 oxide and TiC was stressed. Removals of the oxide phase results in the formation of three-body abrasive particles that were swept across the tape head, and gave rise to three-body abrasive wear, particularly in the pole regions. Hence, PTR and subsequent which signal loss and error growth. The lower contact pressure of the LTO system comparing with the Travan5 system ensures that fewer and smaller three-body abrasive particles were swept across the poles and insulator regions. Hence, lower contact pressure, as well as reducing stain in the same time significantly reduces PTR in the LTO system.

From recession to renewal:the impact of the financial crisis on public services and local government

Book review of From Recession to Renewal: The Impact of the Financial Crisis on Public Services and Local Government, Joanna Richardson (Ed). Bristol, Policy Press, 2010, ISBN 9781847426994

Regional responses to recession:the role of the West Midlands regional taskforce

Bailey D. and Berkeley N. Regional responses to recession: the role of the West Midlands Regional Taskforce, Regional Studies. Regional taskforces were set up across the English regions in late 2008 in response to the most severe recession since the Second World War. This paper examines the role of one such body, the West Midlands Regional Taskforce, as an example of regional response to recession, and offers potential lessons for the future in dealing with such situations. In so doing it reflects on the contested concept of regional 'resilience' and its relevance for policy actions at the regional level. Understanding how the region responded in this way could help in maintaining a 'permanent capacity' to deal with shocks, especially in the context of the abolition of regional development agencies (RDAs) in England from 2012 and their replacement with local enterprise partnerships (LEPs). © 2014 © 2014 The Author(s). Published by Taylor & Francis.

Inward investment and the drivers of post recession recovery in Germany

This paper examines changes in the drivers of productivity in Germany over the period 1997-2012. We start by comparing the performance of German firms and inward investors before and during the recovery from the recent global financial crisis of 2008 across a range of sectors, and subsequently examine the channels through which different firms are able to generate productivity. Our results show that foreign investors are more productive than German MNEs and purely domestic firms, with the gap narrowing in the manufacturing sector, but growing in the service sector during the recovery period. We also contrast those firms for whom productivity growth is related to greater use of intangible assets, compared with those for whom productivity is linked to cash flow. Productivity of inward investors is driven by cash flow rather than intangible assets, these being limited to high-technology investors from the EU and the USA.

Education as a critical practice

Few today doubt that English Higher Education (HE), like the wider world in which it is located, is in crisis. This is, in part, an economic crisis, as the government response to the current recession seems to be that of introducing the kind of neoliberal ‘shock doctrine’ (Klein 2007) or ‘shock therapy’ (Harvey 2005) that previously resulted in swingeing cuts in public services in Southern nations. Our aim in producing this volume is that these contributions help develop a collective response to the seeming limits of these conditions. We view the strength of these contributions in part as providing palpable evidence of how we and our colleagues are acting with critical hope under current conditions so that we might encourage others to work with us to build, together, more progressive formal and informal education systems that address and seek to redress multiple injustices of the world today.

Why critical pedagogy and popular education matter today

Few today doubt that English Higher Education (HE), like the wider world in which it is located, is in crisis. This is, in part, an economic crisis, as the government response to the current recession seems to be that of introducing the kind of neoliberal ‘shock doctrine’ (Klein 2007) or ‘shock therapy’ (Harvey 2005) that previously resulted in swingeing cuts in public services in Southern nations. Our aim in producing this volume is that these contributions help develop a collective response to the seeming limits of these conditions. We view the strength of these contributions in part as providing palpable evidence of how we and our colleagues are acting with critical hope under current conditions so that we might encourage others to work with us to build, together, more progressive formal and informal education systems that address and seek to redress multiple injustices of the world today.

The tribology of laminated magnetic recording heads

This thesis investigates the mechanisms that lead to pole tip recession (PTR) in laminated magnetic recording heads (also known as "sandwich heads"). These heads provide a platform for the utilisation of advanced soft magnetic thin films in practical recording heads suitable for high frequency helical scan tape recording systems. PTR results from a differential wear of the magnetic pole piece from the tape-bearing surface of the head. It results in a spacing loss of the playback or read signal of 54.6dB per recording wavelength separation of the poles from the tape. PTR depends on the material combination used in the head, on the tape type and the climate - temperature and relative humidity (r.h.). Five head materials were studied: two non-magnetic substrate materials- sintered multi granular CaTi03 and composite CaTi03/ZrTi04/Ti02 and three soft magnetic materials- amorphous CoNbZr, and nanocrystalline FeNbSiN and FeTaN. Single material dummy heads were constructed and their wear rates measured when cycling them in a Hi-8 camcorder against commercially available metal particulate (MP) and metal evaporated (ME) tapes in three different climates: 25°C/20%r.h., 25°C/80%r.h. and 40°C/80%r.h. X-ray photoelectron spectroscopy (XPS) was used to examine changes the head surface chemistry. Atomic force microscopy (AFM) was used to examine changes in head and tape surface topography. PTR versus cycling time of laminated heads of CaTi03/ZrTiO4/Ti02 and FeTaN construction was measured using AFM. The principal wear mechanism observed for all head materials was microabrasion caused by the mating body - the tape surface. The variation in wear rate with climate and tape type was due to a variation in severity in this mechanism, except for tape cycling at 40°C in which gross damage was observed to be occurring to the head surface. Two subsidiary wear mechanisms were found: third body scratching (all materials) and grain pullout (both ceramics and FeNbSiN). No chemical wear was observed, though tribochemical reactions were observed on the metal head surfaces. PTR was found to be caused by two mechanisms - the first differential microabrasion of the metal and substrate materials and which was characterised by a low (~10nm) equilibrium value. The second was by deep ploughing by third body debris particles, thought mainly to be grain pullout particles. This level of PTR caused by this mechanism was often more severe, and of a non-equilibrium nature. It was observed more for ME tape, especially at 40°C/80%r.h. and 25°c/20%r.h. Two other phenomena on the laminated head pole piece were observed and commented upon: staining and ripple texturing.

The tribology of linear tape recording systems

This thesis is devoted to the tribology at the head~to~tape interface of linear tape recording systems, OnStream ADRTM system being used as an experimental platform, Combining experimental characterisation with computer modelling, a comprehensive picture of the mechanisms involved in a tape recording system is drawn. The work is designed to isolate the mechanisms responsible for the physical spacing between head and tape with the aim of minimising spacing losses and errors and optimising signal output. Standard heads-used in ADR current products-and prototype heads- DLC and SPL coated and dummy heads built from a AI203-TiC and alternative single-phase ceramics intended to constitute the head tape-bearing surface-are tested in controlled environment for up to 500 hours (exceptionally 1000 hours), Evidences of wear on the standard head are mainly observable as a preferential wear of the TiC phase of the AI203-TiC ceramic, The TiC grains are believed to delaminate due to a fatigue wear mechanism, a hypothesis further confirmed via modelling, locating the maximum von Mises equivalent stress at a depth equivalent to the TiC recession (20 to 30 nm). Debris of TiC delaminated residues is moreover found trapped within the pole-tip recession, assumed therefore to provide three~body abrasive particles, thus increasing the pole-tip recession. Iron rich stain is found over the cycled standard head surface (preferentially over the pole-tip and to a lesser extent over the TiC grains) at any environment condition except high temperature/humidity, where mainly organic stain was apparent, Temperature (locally or globally) affects staining rate and aspect; stain transfer is generally promoted at high temperature. Humidity affects transfer rate and quantity; low humidity produces, thinner stains at higher rate. Stain generally targets preferentially head materials with high electrical conductivity, i.e. Permalloy and TiC. Stains are found to decrease the friction at the head-to-tape interface, delay the TiC recession hollow-out and act as a protective soft coating reducing the pole-tip recession. This is obviously at the expense of an additional spacing at the head-to-tape interface of the order of 20 nm. Two kinds of wear resistant coating are tested: diamond like carbon (DLC) and superprotective layer (SPL), 10 nm and 20 to 40 nm thick, respectively. DLC coating disappears within 100 hours due possibly to abrasive and fatigue wear. SPL coatings are generally more resistant, particularly at high temperature and low humidity, possibly in relation with stain transfer. 20 nm coatings are found to rely on the substrate wear behaviour whereas 40 nm coatings are found to rely on the adhesive strength at the coating/substrate interface. These observations seem to locate the wear-driving forces 40 nm below the surface, hence indicate that for coatings in the 10 nm thickness range-· i,e. compatible with high-density recording-the substrate resistance must be taken into account. Single-phase ceramic as candidate for wear-resistant tape-bearing surface are tested in form of full-contour dummy-heads. The absence of a second phase eliminates the preferential wear observed at the AI203-TiC surface; very low wear rates and no evidence of brittle fracture are observed.

Critical pedagogy/popular education group

Few today doubt that English Higher Education (HE), like the wider world in which it is located, is in crisis. This is, in part, an economic crisis, as the government response to the current recession seems to be that of introducing the kind of neoliberal ‘shock doctrine’ (Klein 2007) or ‘shock therapy’ (Harvey 2005) that previously resulted in swingeing cuts in public services in Southern nations. Our aim in producing this volume is that these contributions help develop a collective response to the seeming limits of these conditions. We view the strength of these contributions in part as providing palpable evidence of how we and our colleagues are acting with critical hope under current conditions so that we might encourage others to work with us to build, together, more progressive formal and informal education systems that address and seek to redress multiple injustices of the world today.

Neo-Nazism in West Germany

The oharaoter of right-wing extremism in the Federal Republic has undergone extensive transformations in the seventies. As electoral support for the extreme Right declined, a whole range of new groupings emerged pursuing a militant extra-parliamentary strategy. Essential charaoteristics are an increasing tendency to use violence and a close ideological affinity to the NSDAP. They attract a growing number of young people. The increasing susceptibility of young people to rightist ideologies coincides with an economic recession of which young people especially are the victims. Widespread ignorance about Nazism and the prevalence of anti-democratic political attitudes constitute important contributary factors and point to a considerable potential for right-extremism in the Federal Republic., This potential can be attributed. to the negative effects of much of the material dealing with the NS past, to serious deficiencies in the area of historical-political education in schools and, above all, to the absence of any :real process of "coming to terms with the past" in the postwar period. Neo-Nazism is not completely isolated from other trends in West German society. Rightist elements within the established party system and broad sections of the population hold similar views and attitudes. This similarity, linked with an over-exaggerated concern with a perceived threat from the extreme Left may explain the absence of any concerted effort to deal with nee-Nazi tendencies. The response of the courts exemplifies a widespread tendency to under-estimate the significance of the extreme Right. Opposition to the Right is restricted primarily to those circles which suffered most under the Nazi regime. The analysis suggests that one must reject the simplistic view that at the present time the Right does not constitute a serious threat to West German democracy. The study evaluates the wide range of views to be found in secondary sources on the subject of neo-Nazism and is :intended, to contribute to the ongoing discussion conceming the potential for right-extremism in West Germany.

Employability management needs analysis and the ICT sector in Europe:the case of small and medium-sized enterprises

The purpose of this paper is to deal with the outcomes of a so-called “employability management needs analysis” that is meant to provide more insight into current employability management activities and its possible benefits for Information and Communication Technology (ICT) professionals working in Small- and Medium-sized enterprises (SMEs) throughout Europe. A considerable series of interviews (N=107) were conducted with managers in SMEs in seven European countries, including Germany, Greece, Italy, the Netherlands, Norway, Poland, and the UK. A semi-structured interview protocol was used during the interviews to cover three issues: employability (13 items), ageing (8 items), and future developments and requirements (13 items). Analysis of all final interview transcriptions was at a national level using an elaborate common coding scheme. Although an interest in employability emerged, actual policy and action lagged behind. The recession in the ICT sector at the time of the investigation and the developmental stage of the sector in each participating country appeared connected. Ageing was not seen as a major issue in the ICT sector because managers considered ICT to be a relatively young sector. There appeared to be a serious lack of investment in the development of expertise of ICT professionals. Generalization of the results to large organizations in the ICT sector should be made with caution. The interview protocol developed is of value for further research and complements survey research undertaken within the employability field of study. It can be concluded that proactive HRM (Human Resource Management) policies and strategies are essential, even in times of economic downturn. Employability management activities are especially important in the light of current career issues. The study advances knowledge regarding HRM practices adopted by SMEs in the ICT sector, especially as there is a gap in knowledge about career development issues in that particular sector.

Self-regulation of health and safety in a Local Authority with particular reference to safety representatives, supervisors and safety committees

The Report of the Robens Committee (1972), the Health and Safety at Work Act (1974) and the Safety Representatives and Safety Committees Regulations (1977) provide the framework within which this study of certain aspects of health and safety is carried out. The philosophy of self-regulation is considered and its development is set within an historical and an industrial relations perspective. The research uses a case study approach to examine the effectiveness of self-regulation in health and safety in a public sector organisation. Within this approach, methodological triangulation employs the techniques of interviews, questionnaires, observation and documentary analysis. The work is based in four departments of a Scottish Local Authority and particular attention is given to three of the main 'agents' of self-regulation - safety representatives, supervisors and safety committees and their interactions, strategies and effectiveness. A behavioural approach is taken in considering the attitudes, values, motives and interactions of safety representatives and management. Major internal and external factors, which interact and which influence the effectiveness of joint self-regulation of health and safety, are identified. It is emphasised that an organisation cannot be studied without consideration of the context within which it operates both locally and in the wider environment. One of these factors, organisational structure, is described as bureaucratic and the model of a Representative Bureaucracy described by Gouldner (1954) is compared with findings from the present study. An attempt is made to ascertain how closely the Local Authority fits Gouldner's model. This research contributes both to knowledge and to theory in the subject area by providing an in-depth study of self-regulation in a public sector organisation, which when compared with such studies as those of Beaumont (1980, 1981, 1982) highlights some of the differences between the public and private sectors. Both empirical data and hypothetical models are used to provide description and explanation of the operation of the health and safety system in the Local Authority. As data were collected during a dynamic period in economic, political and social terms, the research discusses some of the effects of the current economic recession upon safety organisation.

Strategies for agricultural change and the UK balance of payments

The world food crisis, Britain's reliance on imported food and feedstuffs and balance of payments difficulties were some of the factors which lent weight to the call for increased self-sufficiency in Britain's agriculture in the 1970s. This project considers two main areas: an investigation of the impact of radical agricultural change, designed to increase self-sufficiency, on the balance of payments; and, an appraisal of the potential role of the food industry within a radically different food system. The study proceeded by: an examination of the principles of agricultural policy and its development in Britain; an overview of the mechanism and meaning of the balance of payments; a consideration of the debate on agricultural import saving; the construction of radical agricultural strategies; the estimation of effects of the strategies, particularly to the balance of. payments; the role of the food industry and possible innovations within the strategies; a case study of textured vegetable proteins; and, the wider implications of implementation of radical agricultural alternatives. Two strategies were considered: a vegan system, involving no livestock; and, an intermediate system, including some livestock and dairy cattle. The study concludes that although agricultural change could in principle make a contribution to the balance of payments, implementation of agricultural change cannot be justified for this purpose alone. First, balance of payments problems can be solved by more appropriate methods. Second, the UK' s balance of payments problem has disappeared for the time being owing to North Sea oil and economic recession. Third, the political and social consequences of the changes investigated would be unacceptable. Progress in UK food policy is likely to be in the form of an integrated food and health policy.