Power quality improvements for LV networks

In order to increase the capacity of the existing Low Voltage grid, one solution is to increase the nominal residential network voltage from 230 V to 300 V, which is easily accommodated within the voltage rating of existing infrastructure such as cabling. A power electronic AC-AC converter would then be used to step the voltage back down to 230 V at an individual property. Such equipment could also be used to provide power quality improvements on both the utility and customer side of the converter depending on its topology. This paper provides an overview of a project which is looking at the development of such a device. The project is being carried out in collaboration with the local UK, Distribution Network Operator (DNO).

Maximising the economic and social impact of Six Sigma

This paper reports on how Six Sigma training can be made more effective. The research is empirically based. To date it has engaged with over 100 respondents from 60 different organisations around the world. The questionnaire has been derived from leading refereed sources and expert practitioner experience and addresses both success factor and tools issues from three perspectives: (i) academic, (ii) training, and (iii) practice to help maximise economic and social impact of programmes. This topic is important because the popularity of Six Sigma adoption in organisations has grown dramatically over recent years. This is probably because many accounts of great cost savings and quality improvements have been published by major international companies. However, other companies striving to emulate this success are finding that effective implementation needs experienced and well trained individuals. To date, there have been few such surveys and this work-in-progress benchmarking study provides unique insight.

The comparative impact of privatisation and regulation on productivity growth in the English and Welsh water and sewerage industry, 1985-99

After the 10 regional water authorities of England and Wales were privatized in November 1989, the successor WASCs (water and sewerage companies) faced a new regulatory regime that was designed to promote productivity growth while simultaneously improving drinking water and environmental quality. As legally mandated quality improvements necessitated a costly capital investment programme, the industry's economic regulator – the Office of Water Services – implemented a RPI + K pricing system, designed to compensate the WASCs for their capital investment programme while also encouraging faster rates of productivity growth. This paper considers the relative effects of privatization and regulation on productivity growth in the industry using both non-parametric and parametric methods to provide a crosscheck on the robustness of the results. While there is evidence that labour productivity improved after privatization, there is no evidence that privatization led to a growth in TFP (total factor productivity). However, there is some evidence of a small increase in the rate of TFP growth in the aftermath of a substantial tightening of the regulatory regime that took place in 1995. These results, therefore, are consistent with evidence from other research that privatization, in the absence of effective competition and/or regulation, is not necessarily associated with improved economic performance.

Understanding the factors affecting e-business adoption and impact on logistics processes

Purpose: The purpose of this paper is to conceptualize e-business adoption and to generate understanding of the range of factors affecting the adoption process. The paper also aims at exploring the perceived impact of e-business adoption on logistics-related processes. Design/methodology/approach: Case study research, by conducting in-depth interviews in eight companies. Findings: E-business adoption is not exclusively a matter of resources. Increased e-business adoption and impact are caused by increased operational compatibility, as well as increased levels of collaboration. In terms of e-business impact this mainly refers to cycle time reductions and quality improvements, rather than direct cost reductions as reported by other authors. Research limitations/implications: The intrinsic weakness of the research method and the way concepts are operationalized limits the ability to generalize findings. Practical implications: Managers should emphasize developing their relationships with theirsuppliers/customers, in an effort to do common e-business investments, and should aim to increase their partners' commitment to the use of these applications. Originality/value: This paper provides empirical evidence from a sector where limited research efforts have taken place. Explanations can be helpful to other researchers involved in the understanding of the adoption of e-business and its impact. © Emerald Group Publishing Limited.

Organizational change and development in India:a case of strategic organizational change and transformation

Purpose – The purpose of this paper is to examine developments in the field of organizational change (OC) with reference to the context of India. It highlights the need to analyze this topic in the present Indian economic environment and discusses the main developments reported in the Indian literature on the same. Design/methodology/approach – Empirical evidence based on a qualitative analysis of a case study undertaken at a public-private partnership transformation at North Delhi Power Limited (NDPL) in India is presented. Findings – The findings focus on trust building and belongingness for the employees, establishing a high-performance orientation, quality improvements, and the resultant transformations at NDPL. The analysis indicates a number of ways by which NDPL sought to improve its efficiency in order to better adapt to the rapidly changing Indian business environment. Practical implications – Based on the findings, the paper identifies key messages for policy makers and change agents regarding how to transform companies in the rapidly changing business contexts of emerging markets such as India. Originality/value – The paper offers an in-depth analysis of OC practices in a large organization in India.

The impact of privatisation and regulation on the water and sewerage industry in England and Wales:a translog cost function approach

After the ten Regional Water Authorities (RWAs) of England and Wales were privatized in November 1989, the successor Water and Sewerage Companies (WASCs) faced a new regulatory regime that was designed to promote economic efficiency while simultaneously improving drinking water and environmental quality. As legally mandated quality improvements necessitated a costly capital investment programme, the industry's economic regulator, the Office of Water Services (Ofwat), implemented a retail price index (RPI)+K pricing system, which was designed to compensate the WASCs for their capital investment programme while also encouraging gains in economic efficiency. In order to analyse jointly the impact of privatization, as well as the impact of increasingly stringent economic and environmental regulation on the WASCs' economic performance, this paper estimates a translog multiple output cost function model for the period 1985–1999. Given the significant costs associated with water quality improvements, the model is augmented to include the impact of drinking water quality and environmental quality on total costs. The model is then employed to determine the extent of scale and scope economies in the water and sewerage industry, as well as the impact of privatization and economic regulation on economic efficiency.

Evaluation of integration technology approaches in the healthcare supply chain

Healthcare organisations are increasingly being challenged to look at their operations and find opportunities to improve the quality, efficiency and effectiveness of their supply chain services. In light of this situation, there is an apparent need for healthcare organisations to invest in integration technologies and to achieve the integration of supply chain processes, in order to break up the historical structure characterised by numerous interfaces and the segregation of responsibilities. The aim of this paper is to take an independent look at the healthcare supply chain and identify at different levels the core entities, processes, information flows, and system integration challenges which impede supply chain quality improvements to be realised. Moreover, this paper proposes, from an information systems perspective, a framework for the evaluation of different integration technology approaches, which can be used as a potential guideline tool for assessing integration technology alternatives, in order to add value to a healthcare-supply-chain management system. Copyright © 2007 Inderscience Enterprises Ltd.

Power electronic interfaces for low voltage residential networks

A proposal to increase the existing residential LV grid voltage from 230 V to 300 V has been made in order to increase existing network capacity. A power-electronic AC-AC converter is then used to provide 230 V at each property. The equipment can also provide power-quality improvements to the network and load. Several constraints such as temperature rise at the converter location lead to a converter design requiring very high efficiency. In this paper different AC/AC converter topologies are presented which compares the power quality benefits, size and efficiency of each converter. The design and the control technique of the most suitable topology are verified using simulation and preliminary experimentally results of prototype hardware are also included. © 2013 IEEE.

Market quality changes in the London Stock Market

This paper examines the impact that the introduction of a closing call auction had on market quality at the London Stock Exchange. Using estimates from the partial adjustment with noise model of Amihud and Mendelson [Amihud, Y., Mendelson, H., 1987. Trading mechanisms and stock returns: An empirical investigation. Journal of Finance 42, 533–553] we show that opening and closing market quality improved for participating stocks. When we stratify our sample securities into five groups based on trading activity we find that the least active securities experience the greatest improvements to market quality. A control sample of stocks are not characterized by discernable changes to market quality.

Internal service quality and its impact on external service quality:a study of the role of internal customer types and the dimensions which are used to assess internal suppliers within an organisation and how this affects external service quality

This research explores the role of internal customers in the delivery of external service quality. It will consider any potentially different internal customer types that may exist within the organisation. Additionally, it will explore any potential differences in the dimensions that are used to measure service quality internally and externally. If there are different internal customer types then there may be different dimensions which are used to measure service quality between these types and this will be considered also. The approach adopted given the depth and breadth of understanding required, was an action research case based approach. The research objectives were:(i) To determine the dimensions of internal service quality between internal customer supplier cells. (ii) To determine what variation, if any, there is in the dimension sets between internal customer supplier cells. (iii) To determine any ranking in the dimensions that could exist by internal customer supplier cell type. (iv) To investigate the impact of internal service quality on external service quality over time. The research findings were: (i) The majority of the dimensions used in measuring external service quality were also used internally. There were additions of new dimensions however and some dimensions which were used externally, for internal use, had to be redefined. (ii) Variation in dimension sets were revealed during the research. Four different dimension sets were identified and these were matched with four different types of internal service interaction. (iii) Differences in the ranking of dimensions within each dimension set for each internal customer supplier cell type were confirmed. (iv) Internal service quality was seen to influence external service quality but at a cellular level rather than company level. At the company level, the average internal service quality at the start and finish of the research showed no improvement but external service quality had improved. Further investigation at the cellular level showed that improvements in internal service quality had occurred. Those improvements were found to be with the cells that were closest to the customer.The research implications were found to be: (i) some cells may not be necessary in the delivery of external service quality. (ii) The immediacy of the cell to the external customer and number of interactions into and out of that cell has the greatest effect on external customer satisfaction. (iii) Internal service quality may be driven by the customer affecting those cells at the front end of the business first. This then cascades back to those cells which are less immediate until ultimately the whole organisation shows improvements in internal service quality.

Introduction : the role of quality, production and technological innovation in improving competitive performance

Quality, production and technological innovation management rank among the most important matters of concern to modern manufacturing organisations. They can provide companies with the decisive means of gaining a competitive advantage, especially within industries where there is an increasing similarity in product design and manufacturing processes. The papers in this special issue of International Journal of Technology Management have all been selected as examples of how aspects of quality, production and technological innovation can help to improve competitive performance. Most are based on presentations made at the UK Operations Management Association's Sixth International Conference held at Aston University at which the theme was 'Getting Ahead Through Technology and People'. At the conference itself over 80 papers were presented by authors from 15 countries around the world. Among the many topics addressed within the conference theme, technological innovation, quality and production management emerged as attracting the greatest concern and interest of delegates, particularly those from industry. For any new initiative to be implemented successfully, it should be led from the top of the organization. Achieving the desired level of commitment from top management can, however, be a difficulty. In the first paper of this issue, Mackness investigates this question by explaining how systems thinking can help. In the systems approach, properties such as 'emergence', 'hierarchy', 'commnication' and 'control' are used to assist top managers in preparing for change. Mackness's paper is then complemented by Iijima and Hasegawa's contribution in which they investigate the development of Quality Information Management (QIM) in Japan. They present the idea of a Design Review and demonstrate how it can be used to trace and reduce quality-related losses. The next paper on the subject of quality is by Whittle and colleagues. It relates to total quality and the process of culture change within organisations. Using the findings of investigations carried out in a number of case study companies, they describe four generic models which have been identified as characterising methods of implementing total quality within existing organisation cultures. Boaden and Dale's paper also relates to the management of quality, but looks specifically at the construction industry where it has been found there is still some confusion over the role of Quality Assurance (QA) and Total Quality Management (TQM). They describe the results of a questionnaire survey of forty companies in the industry and compare them to similar work carried out in other industries. Szakonyi's contribution then completes this group of papers which all relate specifically to the question of quality. His concern is with the two ways in which R&D or engineering managers can work on improving quality. The first is by improving it in the laboratory, while the second is by working with other functions to improve quality in the company. The next group of papers in this issue all address aspects of production management. Umeda's paper proposes a new manufacturing-oriented simulation package for production management which provides important information for both design and operation of manufacturing systems. A simulation for production strategy in a Computer Integrated Manufacturing (CIM) environment is also discussed. This paper is then followed by a contribution by Tanaka and colleagues in which they consider loading schedules for manufacturing orders in a Material Requirements Planning (MRP) environment. They compare mathematical programming with a knowledge-based approach, and comment on their relative effectiveness for different practical situations. Engstrom and Medbo's paper then looks at a particular aspect of production system design, namely the question of devising group working arrangements for assembly with new product structures. Using the case of a Swedish vehicle assembly plant where long cycle assembly work has been adopted, they advocate the use of a generally applicable product structure which can be adapted to suit individual local conditions. In the last paper of this particular group, Tay considers how automation has affected the production efficiency in Singapore. Using data from ten major industries he identifies several factors which are positively correlated with efficiency, with capital intensity being of greatest interest to policy makers. The two following papers examine the case of electronic data interchange (EDI) as a means of improving the efficiency and quality of trading relationships. Banerjee and Banerjee consider a particular approach to material provisioning for production systems using orderless inventory replenishment. Using the example of a single supplier and multiple buyers they develop an analytical model which is applicable for the exchange of information between trading partners using EDI. They conclude that EDI-based inventory control can be attractive from economic as well as other standpoints and that the approach is consistent with and can be instrumental in moving towards just-in-time (JIT) inventory management. Slacker's complementary viewpoint on EDI is from the perspective of the quality relation-ship between the customer and supplier. Based on the experience of Lucas, a supplier within the automotive industry, he concludes that both banks and trading companies must take responsibility for the development of payment mechanisms which satisfy the requirements of quality trading. The three final papers of this issue relate to technological innovation and are all country based. Berman and Khalil report on a survey of US technological effectiveness in the global economy. The importance of education is supported in their conclusions, although it remains unclear to what extent the US government can play a wider role in promoting technological innovation and new industries. The role of technology in national development is taken up by Martinsons and Valdemars who examine the case of the former Soviet Union. The failure to successfully infuse technology into Soviet enterprises is seen as a factor in that country's demise, and it is anticipated that the newly liberalised economies will be able to encourage greater technological creativity. This point is then taken up in Perminov's concluding paper which looks in detail at Russia. Here a similar analysis is made of the concluding paper which looks in detail at Russia. Here a similar analysis is made of the Soviet Union's technological decline, but a development strategy is also presented within the context of the change from a centralised to a free market economy. The papers included in this special issue of the International Journal of Technology Management each represent a unique and particular contribution to their own specific area of concern. Together, however, they also argue or demonstrate the general improvements in competitive performance that can be achieved through the application of modern principles and practice to the management of quality, production and technological innovation.

Poly(methyl methacrylate) model study of optical surface quality after excimer laser photorefractive keratectomy

Purpose: To evaluate lenses produced by excimer laser ablation of poly(methyl methacrylate) (PMMA) plates. Setting: University research laboratory. Methods: Two Nidek EC-5000 scanning-slit excimer laser systems were used to ablate plane-parallel plates of PMMA. The ablated lenses were examined by focimetry, interferometry, and mechanical surface profiling. Results: The spherical optical powers of the lenses matched the expected values, but the cylindrical powers were generally lower than intended. Interferometry revealed marked irregularity in the surface of negative corrections, which often had a positive “island” at their center. Positive corrections were generally smoother. These findings were supported by the results of mechanical profiling. Contrast sensitivity measurements carried out when observing through ablated lenses whose power had been neutralized with a suitable spectacle lens of opposite sign confirmed that the surface irregularities of the ablated lenses markedly reduced contrast sensitivity over a range of spatial frequencies. Conclusion: Improvements in beam delivery systems seem desirable.

Optical quality for keratoconic eyes with conventional RGP lens and simulated, customised contact lens corrections:a comparison

Purpose: To compare monochromatic aberrations of keratoconic eyes when uncorrected, corrected with spherically-powered RGP (rigid gas-permeable) contact lenses and corrected using simulations of customised soft contact lenses for different magnitudes of rotation (up to 15°) and translation (up to 1mm) from their ideal position. Methods: The ocular aberrations of examples of mild, moderate and severe keratoconic eyes were measured when uncorrected and when wearing their habitual RGP lenses. Residual aberrations and point-spread functions of each eye were simulated using an ideal, customised soft contact lens (designed to neutralise higher-order aberrations, HOA) were calculated as a function of the angle of rotation of the lens from its ideal orientation, and its horizontal and vertical translation. Results: In agreement with the results of other authors, the RGP lenses markedly reduced both lower-order aberrations and HOA for all three patients. When compared with the RGP lens corrections, the customised lens simulations only provided optical improvements if their movements were constrained within limits which appear to be difficult to achieve with current technologies. Conclusions: At the present time, customised contact lens corrections appear likely to offer, at best, only minor optical improvements over RGP lenses for patients with keratoconus. If made in soft materials, however, these lenses may be preferred by patients in term of comfort. © 2012 The College of Optometrists.