Stabilisation of isocyanate cross linked polybutadiene binder

Isocyanate cross-linked hydroxy terminated polybutadiene is used as a binder for solid rocket propellant. Rocket motors containing this propellant require a storage life of at least 20 years. During storage it has been found that the important rubbery properties of the binder can be lost due to oxidative cross-linking of the polybutadiene chains. This could cause catastrophic failure when the rocket motor is required. At present the bis-hindered phenol Calco 2246 is used as a thermal oxidative stabiliser, but it's performance is only adequate. This has led to the search for a more efficient stabiliser system. To hasten the evaluation of new antioxidant systems the use of dynamic thermal analysis was investigated. Results showed that a tentative relationship existed between predictions by thermal analysis and the long term oven ageing for simple single antioxidant systems. But for more complex systems containing either autosynergistic or mixed antioxidants no relationship was observed suggesting that results for such an "accelerated" technique cannot be used for the purpose of extrapolation for long term performance. This was attributed to the short time and more aggressive condition used (hjgher temperature and oxygen rich atmosphere in thermal analysis) altering the mechanism of action of the antioxidants and not allowing time for co-operative effect of the combined antioxidant system to form. One potential problem for the binder system is the use of an diisocyanate as a cross-linking agent. This reacts with the hydroxyl hydrogen on the polymer as well as other active hydrogens such as those contained in a number of antioxidants, affecting both cross-linking and antioxidant effectiveness. Studies in this work showed that only antioxidants containing amine moieties have a significant affect on binder preparation, with the phenolic antioxidants not reacting. This is due to the greater nucleophilicity of the amines. Investigation of a range of antioxidant systems, including potentially homo, hetero and autosynergistic systems, has highlighted a number of systems which show considerably greater effectiveness than the currently used antioxidant Calco 2246. The only single antioxidant which showed improvement was the partially unhindered phenol y-Tocopherol. Of the mixed systems combinations of the sulphur containing antioxidants e.g. DLTP with higher levels of chain-breaking antioxidants, especially Calco 2246, were the most promising. Also the homosynergistic mix of an aromatic amine and a phenol was seen to be very effective but the results were inconsistent. This inconsistency could be explained by the method of sample preparation used. It was shown that the efficiency of a number of antioxidant.s could be dramatically improved by the use of ultrasound during the mixing stage of preparation. The reason for this increase in performance is unclear but in the case of the homosynergistic amine/phenol mix both more efficient mixing and/or the production of a novel mechanism of action are suggested

Degradation and stabilisation of diisocyanate cured polybutadiene

Hydroxyl terminated polybutadiene (HTPB) has been used as a rocket propellant binder which is required to be stored for at least twenty years. It is found that the excellent stress-strain characteristics of this propellant can be totally lost, during this long storage, due to the deterioration of the polybutadiene chains. As a result, the propellant can not stand the service loads, which may lead to a catastrophe. The study of the HTPB binder degradation, below 80°C, has been carried out by investigating the environmental factors and the changes which occur along the macromolecular chains. Results have shown that oxygen is the main factor which causes the crosslinking and chain scission reactions. The former is the predominant reaction and proceeds rapidly under oxygen sufficient environment. The unsaturation of polymer chain, which provides the desired physical properties to the binder, was lost with the increase in crosslink density. At the same time hydroperoxides were found to form and decompose along the polymer chains. Therefore, the deterioration of the binder results from the oxidation of polymer chains. Since the oxidation reaction occurred at higher rate than oxygen diffusion rate and oxygen diffusion rate is inversely proportional to the crosslink density, the binder, below the surface layer in a thick section container, could be naturally protected under an oxygen deficient condition for a long time. Investigation of the effectiveness of antioxidants in HTPB binder has shown that the efficiency of an antioxidant depends on its ability to scavenge radicals. Generally, aromatic amines are the most effective binder antioxidants. But when a peroxide decomposer is combined with an aromatic amine at the appropriate ratio, a synergistic effect is obtained, which gives the lowest binder gel increase rate.

Physicochemical characteristics of chlorofluorohydrocarbon based inhalation aerosols

The aim of this work was to gain a better understanding of the physiochemical factors which affect the formulation of suspension inhalation aerosols. This has been attempted by applying the principles of colloid science to aerosol formulation. Both a drug system and a model colloid system have been used. The adsorption of six nonionic and cationic surfactants onto Spherisorb has been investigated. The results were analysed by calculating the area occupied by one adsorbed molecule at the surface and by comparing these values for each surfactant. The amount of each surfactant adsorbed was correlated with the number of sites on that surfactant molecule which could interact with the surface. The stability of suspensions, produced by both the model colloid Spherisorb, and by the drug isoprenaline sulphate, after adsorption of the surfactants, has been assessed by measuring settling times and rising times. The most stable suspensions were found to be those which had the greatest amounts of long chain fatty acid surfactant adsorbed on their surface. A comparison was made between the effective stabilising properties of Span 85 and oleic acid on various drug suspensions. It was found that Span 85 gave the most stable suspensions. Inhalation aerosol suspensions of isoprenaline sulphate were manufactured using the same surfactants used in the adsorption and suspension stability studies and were analysed by measuring the particle size distributions of the suspension and the emitted doses. The results were found to correlate with the adsorption and suspension stability studies and it was concluded that a deflocculated suspension was preferable to a flocculated suspension in inhalation aerosols provided that the drug density was less than the propellant density. The application of this work to preformulation studies was also discussed.

Novel pMDI formulations for pulmonary delivery of proteins

In this paper, we demonstrate that co-spray-drying a model protein with sodium carboxymethylcellulose (NaCMC) protects protein integrity during spray-drying, and that the resultant spray-dried powders can be successfully dispersed in hydrofluoroalkane (HFA) propellant to prepare pressurised metered dose (pMDI) formulations that exhibit high respirable fractions. The spray-dried powders were formulated as HFA-134a pMDI suspensions in the absence of any other excipients (e.g. surfactants) or co-solvents (e.g. ethanol). The in vitro aerosolisation profile of these systems was assessed using the twin stage impinger; fine particle fractions (FPF) ≥50% of the recovered dose were obtained. Following storage for five months, the aerosolisation performance was reassessed; the NaCMC-free formulation demonstrated a significant decrease in FPF, whereas the performance of the NaCMC-modified formulations was statistically equivalent to their initial performance. Thus, formulation of pMDI suspensions using NaCMC-based spray-dried powders is a promising approach for the pulmonary delivery of proteins and peptides. © 2009 Elsevier B.V. All rights reserved.